VMV. A. Maroni

V. A. Maroni

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


V. A. Maroni has a total of 71 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • On-Line Characterization of YBCO Coated Conductors Using Raman Spectroscopy Methods

    by V. A. Maroni, J. L. Reeves, G. Schwab

    The use of Raman spectroscopy for on-line monitoring of the production of superconducting YBa2Cu3O6+x (YBCO) thin films on long-length metal tapes coated with textured buffer layers is reported for the first time. A methodology is described for obtaining Raman spectra of YBCO on moving tape exiting a metal-organic-chemical-vapor-deposition (MOCVD) enclosure. After baseline correction, the spectra recorded in this way show the expected phonons of the specific YBCO crystal orientation required for high supercurrent transport, as well as phonons of non-superconducting second-phase impurities when present. It is also possible to distinguish YBCO films that are properly textured from films having domains of misoriented YBCO grains. An investigation of the need for focus control on moving tape indicated that focusing of the laser on the surface of the highly reflective YBCO films exiting the MOCVD enclosure tends to produce aberrant photon bursts that swamp the Raman spectrum. These photon bursts are very likely a consequence of optical speckle effects induced by a combination of surface roughness, crystallographic texture, and/or local strain within the small grain microstructure of the YBCO film. Maintaining a slightly out-of-focus condition provides the best signal-to-noise ratio in terms of the obtained Raman spectra. In addition to examining moving tape at the post-MOCVD stage, Raman spectra of the film surface can also be recorded after the oxygen anneal performed to bring the YBCO to the optimum superconducting state. Consideration is given to data processing methods that could be adapted to the on-line Raman spectra to allow the tagging of out-of-specification tape segments and, at a more advanced level, feedback control to the MOCVD process.


  • Practical superconductor development for electrical power applications annual report for FY 2005.

    by U Balachandran, C Cheon, H Claus, S E Dorris, J M Hiller, K E Gray, R E Koritala, Y Lei, B Ma, S H Majumdar, et al.

  • Practical superconductor development for electrical power applications - annual report for FY 2003.

    by U Balachandran, R Baurceanu, H Clauss, S E Dorris, J E Emerson, R A Erck, B L Fisher, K E Gray, J R Hull, R E Koritala, et al.

    Most large-scale applications of high-critical-temperature superconductors will require conductors that can carry large currents in the presence of applied magnetic fields. This report describes progress at Argonne National Laboratory (ANL) in the research and development of practical superconducting components and devices. These efforts primarily focus on the use of Y-Ba-Cu-O system in second-generation conductors, but they also include investigations of Bi-Pb-Sr-Ca-Cu-O systems for use in first-generation conductors. Results are presented in the areas of processing first-generation superconductors and second-generation (2G) superconductors with several different architectures, applying Raman microscopy to the characterization of 2G conductors, studying the role of oxygen doping in the grain boundary transport of 2G conductors, and evaluating the mechanical properties of 2G conductors.

  • Practical superconductor development for electrical power applications: annual report for FY 2002.

    by R Baurceanu, Y S Cha, S E Dorris, J E Emerson, R A Erck, B L Fisher, K E Gray, H Claus, J R Hull, Y Jee, et al.

    Most large-scale applications of high-critical-temperature superconductors will require conductors that can carry large currents in the presence of applied magnetic fields. This report describes progress at Argonne National Laboratory (ANL) in the research and development of practical superconducting components and devices using the Y-Ba-Cu-O and Bi-Pb-Sr-Ca-Cu-O systems. Results are presented in the areas of fabrication of second- and first-generation composite conductors, characterization of their structures and superconducting properties, investigation of grain-boundary current transport and factors that influence it, testing and modeling of the components of a superconducting fault current limiter, and the measurement and modeling of a superconductor's response to a transient such as that in a fault current limiter after a fault.

  • Improved microstructure in Ag/Bi-2223 composite tapes by systematic variation of heat treatment parameters

    by Y L Tang, D J Miller, R M Baurceanu, V A Maroni, R D Parrella

    Multifilament-type, silver-sheathed (Bi, Pb)2Sr2Ca2Cu3Ox (Ag/Bi-2223) composite tapes produced by the powder-in-tube (PIT) method were given a first heat treatment that employed either a standard (STD) single oxygen pressure/temperature (pO2/T) set point or a novel variable pO2/T treatment referred to as thermal sliding heat treatment (TSHT). X-ray diffraction, scanning electron microscopy, energy dispersive x-ray spectroscopy and transmission electron microscopy were employed to provide a comparative analysis of the Bi-2223 grain colony microstructure and connectivity, nonsuperconducting second phase (NSP) composition and distribution, and grain boundary character in the STD- and TSHT-type post-first-heat-treatment Ag/Bi-2223 tape specimens. The dominant NSPs in STD and TSHT specimens were (Ca, Sr)2CuO3, (Ca, Sr)14Cu24O41, and amorphous phases that were randomly distributed in the filaments. The number and size of the NSPs in the STD specimens were sufficient to cause substantial misalignment of Bi-2223 grain colonies throughout the filament cores. However, the TSHT specimens (when compared to the STD specimens) expressed an improved microstructure with fewer/smaller NSPs that were localized mainly in the interior regions of the filaments. Also, the Bi-2223 grain colonies in TSHT specimens were more robust and better aligned from the silver-sheath/Bi-2223 interface to the mid-core region of each filament.


  • Practical superconductor development for electrical power applications : annual report for FY 2001.

    by Y S Cha, S E Dorris, J T Dusek, J E Emerson, R A Erck, B L Fisher, K C Goretta, K E Gray, J R Hull, Y Jee, et al.

    Most large-scale applications of high-critical-temperature superconductors will require wires or tapes that can carry large current in applied magnetic fields. This report describes research and development efforts at Argonne National Laboratory (ANL) aimed at producing practical superconducting components and devices using the Y-Ba-Cu-O and Bi-(Pb)-Sr-Ca-Cu-O systems. Topics discussed include various methods of forming second- and first-generation composite conductors, characterization of their structures and superconducting and mechanical properties, modeling of grain-boundary current transport, and the testing and modeling of a superconducting fault current limiter.

  • Practical superconductor development for electrical power applications - annual report for FY 2000.

    by U Balachandran, Y S Cha, S E Dorris, J T Dusek, J E Emerson, B L Fisher, K C Goretta, K E Gray, J R Hull, Y Jee, et al.

    Most large-scale high-critical-temperature superconductor applications require wires or tapes that an carry high currents in applied magnetic fields. This report describes technical progress of research and development efforts aimed at producing superconducting components and devices in the Y-Ba-Cu-O and Bi-(Pb)-Sr-Ca-Cu-O systems. Topics discussed are formation of first- and second-generation composite conductors, characterization of structures and superconducting and mechanical properties, modeling of grain-boundary current transport, and fabrication and analysis of prototype components.

  • Practical superconductor development for electrical power applications annual report for FY 1998.

    by T.R. Askew, U. Balachandran, Y.S. Cha, S.E. Dorris, J.T. Dusek, J.E. Emerson, B.L. Fisher, K.C. Goretta, K.E. Gray, J.R. Hull, et al.

    Development of useful high-T{sub c} superconductors requires synthesis of superconducting compounds; fabrication of wires, tapes, and films from these compounds; production of composite structures that incorporate stabilizers or insulators; and design and testing of efficient components. This report describes FY 1998 technical progress of research and development efforts aimed at producing superconducting components in the Bi-(Pb)-Sr-Ca-Cu and Y-Ba-Cu oxide systems. Topics discussed are synthesis and heat treatment of high-T{sub c} superconductors, formation of monolithic and composite conductors, characterization of structures and superconducting and mechanical properties, and fabrication and testing of prototype components. Collaborations with industry and academia are documented.