Svetlana Nestorovic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Svetlana Nestorovic has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Desimir Markovic
Tehnički fakultet, Bor
2 shared publications- Ivana Marković
University of Belgrade, Technical Faculty in Bor, VJ 12, 19210 Bor, Serbia
2 shared publications Desimir Marković
University of Belgrade, Technical Faculty in Bor, Serbia
1 shared publicationIvana Rangelov
Tehnički fakultet, Bor
1 shared publicationLj. Ivanic
Technical Faculty Bor, University of Belgrade
1 shared publication- Mirjana Rajcic-Vujasinovic
Tehnički fakultet, Bor
1 shared publication
Latest Publications
- Open Access
- 1 January 2013
- Published by National Library of Serbia in Journal of the Serbian Chemical Society
- Vol. 78 (10) , 1583-1594
Comparison of electrochemical behavior of cast and sintered CuAg4at.% alloy during thermomechanical treatment
The paper presents comparison of electrochemical behavior of samples of CuAg4at.% alloy obtained by powder metallurgy method and the same alloy obtained by melting and casting during oxidation in an alkaline medium. Investigated alloy exhibits anneal hardening effect, so it was examined in each stage of thermomechanical treatment resulting in this effect. Cyclic voltammetry investigations show that both sintered and cast samples after cold rolling to final reduction of 60 % behave as completely homogenous phases. In that stage of thermomechanical treatment peaks corresponding to reactions on silver do not appear and currents on cyclic voltammograms are lowest. After annealing below the recrystallization temperature both samples exhibit anneal hardening; in this stage sintered alloy retains its corrosion stability, whereas current densities for the cast alloy increase and the peaks characteristic for silver appear again. Further annealing above the recrystallization temperature leads to the increasing of current density on voltammograms for samples obtained by both methods and all characteristic current peaks for silver reappear
- 1 January 2013
- Published by National Library of Serbia in Journal of the Serbian Chemical Society
- Vol. 78 (10) , 1583-1594
Open AccessComparison of electrochemical behavior of cast and sintered CuAg4at.% alloy during thermomechanical treatment
The paper presents comparison of electrochemical behavior of samples of CuAg4at.% alloy obtained by powder metallurgy method and the same alloy obtained by melting and casting during oxidation in an alkaline medium. Investigated alloy exhibits anneal hardening effect, so it was examined in each stage of thermomechanical treatment resulting in this effect. Cyclic voltammetry investigations show that both sintered and cast samples after cold rolling to final reduction of 60 % behave as completely homogenous phases. In that stage of thermomechanical treatment peaks corresponding to reactions on silver do not appear and currents on cyclic voltammograms are lowest. After annealing below the recrystallization temperature both samples exhibit anneal hardening; in this stage sintered alloy retains its corrosion stability, whereas current densities for the cast alloy increase and the peaks characteristic for silver appear again. Further annealing above the recrystallization temperature leads to the increasing of current density on voltammograms for samples obtained by both methods and all characteristic current peaks for silver reappear
- 20 August 2009
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 31 (3) , 1644-1649
Influence of thermomechanical treatment on the hardening mechanisms and structural changes of a cast Cu–6.6wt.%Ag alloy
- 20 August 2009
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 31 (3) , 1644-1649
Influence of thermomechanical treatment on the hardening mechanisms and structural changes of a cast Cu–6.6wt.%Ag alloy
- Open Access
- 1 January 2008
- Published by National Library of Serbia in Hemijska industrija
- Vol. 62 (2) , 78-84
Correlation between mechanical properties and structural changes of the sintered Cu-4 at% Ag alloy during thermomechanical treatment
Influence of thermomechanical treatment on micro structure and strength (hardness and microhardness) of the sintered copper based Cu-4 at% Ag alloy was investigated using Vickers hardness and microhardness measurements, and optical microscopy. After sintering at 790?C, samples of Cu-4 at% Ag alloy were subjected to thermomechanical treatment by cold rolling with 20, 40 and 60% deformation degrees, and annealing below and over the recrystallization temperature. It was shown that microstructure of Cu-4 at% Ag alloy changed with thermomechanical treatment, which directly causes changes of mechanical properties. Optical microphotograph of the sintered Cu-4 at% Ag alloy shows relatively homogeneous structure with spherical pores presented. The strength (hardness and microhardness) of the sintered Cu-4 at% Ag alloy during cold rolling increases with deformation degree due to deformation strengthening. Maximum values of hardness and microhardness were for 60% deformation. The porosity still exists in spite of the fact that compacting was carried out during the cold rolling. The hardness and microhardness continue to increase after annealing at temperature bellow recrystallization temperature due to anneal hardening effect which occurs in a temperature range of 160-350?C. It was concluded that solute segregation to dislocations, analogous to the formation of Cottrel atmosphere in interstitial solid solutions, is primarily responsible for anneal hardening phenomenon. Annealing at higher temperatures (higher than 400?C) results in strength decrease due to beginning of alloy recrystallization.
- 1 January 2008
- Published by National Library of Serbia in Hemijska industrija
- Vol. 62 (2) , 78-84
Open AccessCorrelation between mechanical properties and structural changes of the sintered Cu-4 at% Ag alloy during thermomechanical treatment
Influence of thermomechanical treatment on micro structure and strength (hardness and microhardness) of the sintered copper based Cu-4 at% Ag alloy was investigated using Vickers hardness and microhardness measurements, and optical microscopy. After sintering at 790?C, samples of Cu-4 at% Ag alloy were subjected to thermomechanical treatment by cold rolling with 20, 40 and 60% deformation degrees, and annealing below and over the recrystallization temperature. It was shown that microstructure of Cu-4 at% Ag alloy changed with thermomechanical treatment, which directly causes changes of mechanical properties. Optical microphotograph of the sintered Cu-4 at% Ag alloy shows relatively homogeneous structure with spherical pores presented. The strength (hardness and microhardness) of the sintered Cu-4 at% Ag alloy during cold rolling increases with deformation degree due to deformation strengthening. Maximum values of hardness and microhardness were for 60% deformation. The porosity still exists in spite of the fact that compacting was carried out during the cold rolling. The hardness and microhardness continue to increase after annealing at temperature bellow recrystallization temperature due to anneal hardening effect which occurs in a temperature range of 160-350?C. It was concluded that solute segregation to dislocations, analogous to the formation of Cottrel atmosphere in interstitial solid solutions, is primarily responsible for anneal hardening phenomenon. Annealing at higher temperatures (higher than 400?C) results in strength decrease due to beginning of alloy recrystallization.
- Open Access
- 1 January 2003
- Published by National Library of Serbia in Journal of Mining and Metallurgy, Section B: Metallurgy
- Vol. 39 (3-4) , 489-497
Influence of time of annealing on anneal hardening effect of a cast CuZn alloy
Investigated cast copper alloy containing 8at%Zn of a solute. For comparison parallel specimens made from cast pure copper. Copper and copper alloy were subjected to cold rolling with different a final reduction of 30,50 and 70%. The cold rolled copper and copper alloy samples were isochronally and isothermally annealed up to recrystallization temperature. After that the values of hardness, strength and electrical conductivity were measured and X-ray analysis was performed. These investigations show that anneal hardening effect at alloys was attained under recrystallization temperature in the temperature range of 180-3000C, followed with an increase in hardness. The amount of strengthening increase with increasing degree of prior cold work. Also the X-ray analysis show the change of lattice parameter during annealing when anneal hardening effect was attained.
- 1 January 2003
- Published by National Library of Serbia in Journal of Mining and Metallurgy, Section B: Metallurgy
- Vol. 39 (3-4) , 489-497
Open AccessInfluence of time of annealing on anneal hardening effect of a cast CuZn alloy
Investigated cast copper alloy containing 8at%Zn of a solute. For comparison parallel specimens made from cast pure copper. Copper and copper alloy were subjected to cold rolling with different a final reduction of 30,50 and 70%. The cold rolled copper and copper alloy samples were isochronally and isothermally annealed up to recrystallization temperature. After that the values of hardness, strength and electrical conductivity were measured and X-ray analysis was performed. These investigations show that anneal hardening effect at alloys was attained under recrystallization temperature in the temperature range of 180-3000C, followed with an increase in hardness. The amount of strengthening increase with increasing degree of prior cold work. Also the X-ray analysis show the change of lattice parameter during annealing when anneal hardening effect was attained.