Davide Uglietti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Davide Uglietti has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Seyong Choi
2 shared publicationsHitoshi Kitaguchi
1 shared publicationKyoji Zaitsu
1 shared publicationMamoru Hamada
1 shared publication- S. Matsumoto
National Institute for Materials Science
1 shared publication T. Kiyoshi
NIMS, Superconducting Mat Ctr, Magnet Dev Grp, Tsukuba, Ibaraki, Japan
1 shared publication
Latest Publications
- 30 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 2889-2892
The Electrical and Mechanical Characterization of Metal-Reinforced Bi-2223/Ag Conductors for High Field Insert Coil
In this study, we investigated in field properties of high-Tc superconductor (HTS) tapes electrically as well as mechanically. Metallic reinforced Bi-2223/Ag superconductor tapes were used in this work. The critical current (Ic), which is highly dependent on the magnetic field, was measured using fields applied parallel and perpendicular to the tape surface. The conductor was exposed to fields of up to 28 T at 4.2 K. In order to confirm the performance of tapes in practical NMR operation, Ic was also measured around 2 K. The conductor was wound on a large diameter bobbin and mechanical properties were then measured as the coil current was increased. Finally, we verified the conductor properties from coil Ic and maximum stress/strain of it.
- 30 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 2889-2892
The Electrical and Mechanical Characterization of Metal-Reinforced Bi-2223/Ag Conductors for High Field Insert Coil
In this study, we investigated in field properties of high-Tc superconductor (HTS) tapes electrically as well as mechanically. Metallic reinforced Bi-2223/Ag superconductor tapes were used in this work. The critical current (Ic), which is highly dependent on the magnetic field, was measured using fields applied parallel and perpendicular to the tape surface. The conductor was exposed to fields of up to 28 T at 4.2 K. In order to confirm the performance of tapes in practical NMR operation, Ic was also measured around 2 K. The conductor was wound on a large diameter bobbin and mechanical properties were then measured as the coil current was increased. Finally, we verified the conductor properties from coil Ic and maximum stress/strain of it.
- 30 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 1262-1265
Optimization of the Superconducting and Mechanical Properties of Conductors for High Field Solenoid Magnets
Superconductors for high field magnets should have high mechanical strength, high Young modulus as well as high critical current density. The optimization of these properties is very important in the design of a magnet and its conductors. In case of high field solenoids, the main factor limiting the coil current is the mechanical properties of the conductors. A new optimization procedure for conductors is introduced, starting from the competition between the transport properties and the mechanical properties. The balance between mechanical and transport properties are calculated depending on the coil diameter and on the applied magnetic field, and examples of applications to Bi2223 tapes are presented.
- 30 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 1262-1265
Optimization of the Superconducting and Mechanical Properties of Conductors for High Field Solenoid Magnets
Superconductors for high field magnets should have high mechanical strength, high Young modulus as well as high critical current density. The optimization of these properties is very important in the design of a magnet and its conductors. In case of high field solenoids, the main factor limiting the coil current is the mechanical properties of the conductors. A new optimization procedure for conductors is introduced, starting from the competition between the transport properties and the mechanical properties. The balance between mechanical and transport properties are calculated depending on the coil diameter and on the applied magnetic field, and examples of applications to Bi2223 tapes are presented.
- 30 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 2909-2912
Angular Dependence of Critical Current in Coated Conductors at 4.2 K and Magnet Design
Coated conductor tapes are promising materials for the construction of high field inserts (> 20 T). In a magnet, the magnetic field at the coil ends is not parallel to the wide face of the tape, and the angle can reach values larger than 10 degrees. Coated conductors have very anisotropic transport properties, thus it is very important to measure the angular dependence of the critical current. The critical current of commercial YBCO coated conductors made by SuperPower has been measured at 12 T, 4.2 K as a function of the angle between the magnetic field and the wide face of the tape, with a precision of less than 0.2 degree. The experimental results have been used for designing insert coils for high field magnets: depending on the coil parameters and current, the high sensitivity to the magnetic field angle of YBCO tape can affect the performances of the coil.
- 30 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 19 (3) , 2909-2912
Angular Dependence of Critical Current in Coated Conductors at 4.2 K and Magnet Design
Coated conductor tapes are promising materials for the construction of high field inserts (> 20 T). In a magnet, the magnetic field at the coil ends is not parallel to the wide face of the tape, and the angle can reach values larger than 10 degrees. Coated conductors have very anisotropic transport properties, thus it is very important to measure the angular dependence of the critical current. The critical current of commercial YBCO coated conductors made by SuperPower has been measured at 12 T, 4.2 K as a function of the angle between the magnetic field and the wide face of the tape, with a precision of less than 0.2 degree. The experimental results have been used for designing insert coils for high field magnets: depending on the coil parameters and current, the high sensitivity to the magnetic field angle of YBCO tape can affect the performances of the coil.