YXYuan Xia

Yuan Xia

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yuan Xia has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Study on Discharge Characteristics and Microstructural Evolution of PEO Coatings Based on an Al/Ti Tracer Substrate

    by Guodong Li, Guang Li, Yuan Xia

    In this study, samples underwent plasma electrolytic oxidation (PEO) treatment using Al/Ti tracer substrates for 5, 10, 20, 35, and 55 min. The ionization states were determined using Optical Emission Spectroscopy (OES). Microstructural and elemental analyses were conducted using scanning electron microscopy equipped with energy dispersive spectrometry (SEM-EDS). The structural organization and phase composition of the coatings were characterized using X-ray diffraction (XRD) and Raman spectroscopy, respectively. The research findings indicate that the early discharge stage is dominated by discharge within the pre-deposited Al layer, which undergoes gradual oxidation along the thickness direction, while Ti (0.25 wt%) is found on the coating surface. The power increase was 56% of the total increase from min 5 to min 10 of discharge. As discharge time increased, the spectral peaks corresponding to Ti gradually became stronger and were accompanied by gradual enhancement of the crystallinity of the anatase and rutile phases within the coating. The coating surface displayed closed and semi-closed pores in the middle of the discharge. After 55 min of discharge, amorphous SiO2 was observed and Ti content on the coating surface increased to 4.59 wt%.


  • Open Access

    Influence of Applied Frequency on Thermal Physical Properties of Coatings Prepared on Al and AlSi Alloys by Plasma Electrolytic Oxidation

    by Guodong Li, Fei Ma, Zhijie Li, Yi Xu, Fangyuan Gao, Lingyan Guo, Jianwei Zhu, Guang Li, Yuan Xia

    In this study, plasma electrolytic oxidation (PEO) was performed on Al and AlSi substrates using a pulsed direct current (DC) power source. The coating process was carried out in a Na2SiO3 electrolyte with the systematic change of pulse frequency (50–1400 Hz). The surface characteristics of the coatings were examined using scanning electron microscopy (SEM). The phase structure was characterized using X-ray diffraction (XRD). A differential scanning calorimeter (DSC) and a laser flash apparatus (LFA) were employed to test heat capacity and heat conductivity, respectively. Results showed that as the discharge frequency increased, the thermal physical properties of Al-PEO and AlSi-PEO coatings changed in different ways. At a high frequency, Al-PEO coatings had low porosity and were closed-pore structured whereas AlSi-PEO coatings had high porosity and large-size open-pore structures could be observed on their surfaces due to concentrated discharges. Based on these findings, it was found that the thermal productivity of coatings is closely correlated with the open-/closed-pore structure instead of porosity. PEO coatings with low heat capacity or low heat conductivity could be obtained with a controlled frequency.


  • Open Access

    Effect of Cr Atom Plasma Emission Intensity on the Characteristics of Cr-DLC Films Deposited by Pulsed-DC Magnetron Sputtering

    by Guang Li, Yi Xu, Yuan Xia

    A pulsed-dc (direct current) magnetron sputtering with a plasma emission monitor (PEM) system was applied to synthesize Cr-containing hydrogenated amorphous diamond-like carbon (Cr-DLC) films using a large-size industrial Cr target. The plasma emission intensity of a Cr atom at 358 nm wavelength was characterized by optical emission spectrometer (OES). C2H2 gas flow rate was precisely adjusted to obtain a stable plasma emission intensity. The relationships between Cr atom plasma emission intensity and the element concentration, cross-sectional morphology, deposition rate, microstructure, mechanical properties, and tribological properties of Cr-DLC films were investigated. Scanning electron microscope and Raman spectra were employed to analyze the chemical composition and microstructure, respectively. The mechanical and tribological behaviors were characterized and analyzed by using the nano-indentation, scratch test instrument, and ball-on-disk reciprocating friction/wear tester. The results indicate that the PEM system was successfully used in magnetron sputtering for a more stable Cr-DLC deposition process.