HIHironori Iwai

Hironori Iwai

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hironori Iwai has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A 355-nm Direct-Detection Doppler Wind Lidar for Vertical Atmospheric Motion

    by Shoken Ishii, Hideki Takenaka, Kodai Kishibuchi, Yoshitaka Jin, Tomoaki Nishizawa, Nobuo Sugimoto, Hironari Iwai, Makoto Aoki, Seiji Kawamura, Hajime Okamoto

  • Open Access

    Validation of Aeolus Level 2B wind products using wind profilers, ground-based Doppler wind lidars, and radiosondes in Japan

    by Hironori Iwai, Makoto Aoki, Mitsuru Oshiro, Shoken Ishii

    The first space-based Doppler wind lidar (DWL) on board the Aeolus satellite was launched by the European Space Agency (ESA) on 22 August 2018 to obtain global profiles of horizontal line-of-sight (HLOS) wind speed. In this study, the Raleigh-clear and Mie-cloudy winds for periods of baseline 2B02 (from 1 October to 18 December 2018) and 2B10 (from 28 June to 31 December 2019 and from 20 April to 8 October 2020) were validated using 33 wind profilers (WPRs) installed all over Japan, two ground-based coherent Doppler wind lidars (CDWLs), and 18 GPS radiosondes (GPS-RSs). In particular, vertical and seasonal analyses were performed and discussed using WPR data. During the baseline 2B02 period, a positive bias was found to be in the ranges of 0.5 to 1.7 m s−1 for Rayleigh-clear winds and 1.6 to 2.4 m s−1 for Mie-cloudy winds using the three independent reference instruments. The statistical comparisons for the baseline 2B10 period showed smaller biases, −0.8 to 0.5 m s−1 for the Rayleigh-clear and −0.7 to 0.2 m s−1 for the Mie-cloudy winds. The vertical analysis using WPR data showed that the systematic error was slightly positive in all altitude ranges up to 11 km during the baseline 2B02 period. During the baseline 2B10 period, the systematic errors of Rayleigh-clear and Mie-cloudy winds were improved in all altitude ranges up to 11 km as compared with the baseline 2B02. Immediately after the launch of Aeolus, both Rayleigh-clear and Mie-cloudy biases were small. Within the baseline 2B02, the Rayleigh-clear and Mie-cloudy biases showed a positive trend. For the baseline 2B10, the Rayleigh-clear wind bias was generally negative for all months except August 2020, and Mie-cloudy wind bias gradually fluctuated. Both Rayleigh-clear and Mie-cloudy biases did not show a marked seasonal trend and approached zero towards September 2020. The dependence of the Rayleigh-clear wind bias on the scattering ratio was investigated, showing that there was no significant bias dependence on the scattering ratio during the baseline 2B02 and 2B10 periods. Without the estimated representativeness error associated with the comparisons using WPR observations, the Aeolus random error was determined to be 6.7 (5.1) and 6.4 (4.8) m s−1 for Rayleigh-clear (Mie-cloudy) winds during the baseline 2B02 and 2B10 periods, respectively. The main reason for the large Aeolus random errors is the lower laser energy compared to the anticipated 80 mJ. Additionally, the large representativeness error of the WPRs is probably related to the larger Aeolus random error. Using the CDWLs, the Aeolus random error estimates were in the range of 4.5 to 5.3 (2.9 to 3.2) and 4.8 to 5.2 (3.3 to 3.4) m s−1 for Rayleigh-clear (Mie-cloudy) winds during the baseline 2B02 and 2B10 periods, respectively. By taking the GPS-RS representativeness error into account, the Aeolus random error was determined to be 4.0 (3.2) and 3.0 (2.9) m s−1 for Rayleigh-clear (Mie-cloudy) winds during the baseline 2B02 and 2B10 periods, respectively.


  • Open Access

    Validation of Aeolus Level 2B wind products using wind profilers, ground-based Doppler wind lidars, and radiosondes in Japan

    by Hironori Iwai, Makoto Aoki, Mitsuru Oshiro, Shoken Ishii

    The first space-based Doppler wind lidar (DWL) onboard the Aeolus satellite was launched by the European Space Agency (ESA) on 22 August 2018 to obtain global profiles of horizontal line-of-sight (HLOS) wind speed. In this study, the Raleigh-clear and Mie-cloudy winds for periods of baseline 2B02 (from 1 October to 18 December 2018) and 2B10 (from 28 June to 31 December 2019 and from 20 April to 8 October 2020) were validated using 33 wind profilers (WPRs) installed all over Japan, two ground-based coherent Doppler wind lidars (CDWLs), and 18 GPS-radiosondes (GPS-RSs). In particular, vertical and seasonal analyses were performed and discussed using WPR data. During the baseline 2B02 period, a positive bias was found to be in the ranges of 0.46–1.69 m s−1 for Rayleigh-clear winds and 1.63–2.42 m s−1 for Mie-cloudy winds using the three independent reference instruments. The biases of Rayleigh-clear and Mie-cloudy winds were in the ranges of −0.82−+0.45 m s−1 and −0.71−+0.16 m s−1 during the baseline 2B10 period, respectively. The systematic error for the baseline 2B10 was improved as compared with that for the baseline 2B02. The vertical analysis using WPR data showed that the systematic error was slightly positive in all altitude ranges up to 11 km during the baseline 2B02 period. During the baseline 2B10 period, the systematic errors of Rayleigh-clear and Mie-cloudy winds were improved in all altitude ranges up to 11 km as compared with the baseline 2B02. Immediately after the launch of Aeolus, both Rayleigh-clear and Mie-cloudy biases were small. Within the baseline 2B02, the Rayleigh-clear and Mie-cloudy biases showed a positive trend. For the baseline 2B10, the Rayleigh-clear wind bias was generally negative at all months except August 2020, and Mie-cloudy wind bias gradually fluctuated. The systematic error was close to zero with time in 2020 and did not show a marked seasonal trend. The dependence of the Rayleigh-clear wind bias on the scattering ratio was investigated, showing that the scattering ratio had a minimal effect on the systematic error of the Rayleigh-clear winds during the baseline 2B02 period. On the other hand, during the baseline 2B10 period, there was no significant bias dependence on the scattering ratio. Without the estimated representativeness error associated with the comparisons using WPR observations, the Aeolus random error was determined to be 6.71 (5.12) and 6.42 (4.80) m s−1 for Rayleigh-clear (Mie-cloudy) winds during the baseline 2B02 and 2B10 periods, respectively. The main reason for the large random errors is probably related to the large representativeness error due to the large sampling volume of the WPRs. Using the CDWLs, the Aeolus random error estimates were in the range of 4.49–5.31 (2.93–3.19) and 4.81–5.21 (3.30–3.37) m s−1 for Rayleigh-clear (Mie-cloudy) winds during the baseline 2B02 and 2B10 periods, respectively. By taking the GPS-RS representativeness error into account, the Aeolus random error was determined to be 4.01 (3.24) and 3.02 (2.89) m s−1 for Rayleigh-clear (Mie-cloudy) winds during the baseline 2B02 and 2B10 periods, respectively.


  • Open Access

    Study of Thermal Activity in The Mixing Layer During First Generated Single Cloud by Using Combined Observation From Boundary Layer Radar, Doppler Lidar and Time Lapse Camera 

    by Ginaldi Ari Nugroho, Kosei Yamaguchi, Eiichi Nakakita, Masayuki K. Yamamoto, Seiji Kawamura, Hironori Iwai

    Detailed observation of small scale perturbation in the atmospheric boundary layer during the first generated cumulus cloud are conducted. Our target is to study this small scale perturbation, especially related to the thermal activity at the first generated cumulus cloud. The observation is performed during the daytime on August 17, 2018, and September 03, 2018. Location is focused in the urban area of Kobe, Japan. High-resolution instruments such as Boundary Layer Radar, Doppler Lidar, and Time Lapse camera are used in this observation. Boundary Layer Radar, and Doppler Lidar are used for clear air observation. Meanwhile Time Lapse Camera are used for cloud existence observation. The atmospheric boundary layer structure is analyzed based on vertical velocity profile, variance, skewness, and estimated atmospheric boundary layer height. Wavelet are used to observe more of the period of the thermal activity. Furthermore, time correlation between vertical velocity time series from height 0.3 to 2 km and image pixel of generated cloud time series are also discussed in this study.

  • Open Access

    Case Study on Convection Initiation Associated with an Isolated Convective Storm Developed over Flat Terrain during TOMACS

    by Hironori Iwai, Shoken Ishii, Seiji Kawamura, Eiichi Sato, Kenichi Kusunoki

    Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies


  • Open Access

    Performance and Technique of Coherent 2-μm Differential Absorption and Wind Lidar for Wind Measurement

    by Hironori Iwai, Shoken Ishii, Ryoko Oda, Kohei Mizutani, Shinya Sekizawa, Yasuhiro Murayama

    A coherent 2-μm differential absorption and wind lidar (Co2DiaWiL) has been built with a high-power Q-switched Tm,Hm:YLF laser to measure CO2 concentration and radial wind speed. The performance of the Co2DiaWiL is described and analyzed, with a view to demonstrating system capabilities for remote measurements of wind velocities in the atmospheric boundary layer and free troposphere. Bias in the velocity measurements was estimated at −0.0069 m s−1 using measurements from a stationary hard target. The Co2DiaWiL achieved a velocity precision of 0.12 m s−1, derived from the magnitude of random error in radial wind velocity measurements. These measurements were made for ranges out to 20–25 km by using a horizontally fixed beam mode for average times of 1 min. Quantitative intercomparisons of 1-min averages between the Co2DiaWiL and a sonic anemometer revealed a correlation coefficient of 0.99. This study demonstrated measurements of horizontal wind profiles, by making radial wind velocity measurements with the Co2DiaWiL using conical scanning. Profile differences at higher levels could be attributed to probable large horizontal separations of the radiosondes and the low signal-to-noise ratio of the Co2DiaWiL. A pseudo-dual-Doppler technique was developed to retrieve horizontal wind components with a single-Doppler lidar and a steering mirror. Intercomparisons of the 1-min-averaged u and υ components from the pseudo-dual-Doppler lidar measurements with those from the sonic anemometer revealed correlation coefficients of 0.84 and 0.83, respectively.


  • Partial CO2 Column-Averaged Dry-Air Mixing Ratio from Measurements by Coherent 2-μm Differential Absorption and Wind Lidar with Laser Frequency Offset Locking

    by Shoken Ishii, Kohei Mizutani, Philippe Baron, Hironori Iwai, Ryoko Oda, Toshikazu Itabe, Hirotake Fukuoka, Takayoshi Ishikawa, Mizuki Koyama, Tomoaki Tanaka, et al.

    A coherent 2-μm differential absorption and wind lidar (Co2DiaWiL) with a 2-μm single-frequency Q-switched laser with laser frequency offset locking was used for long-range CO2 measurement. The frequency stabilization of the single-frequency λ on pulsed laser was 1.0 MHz. Experimental horizontal CO2 measurement over a column range of 2.6–5.6 km and 900 shot pairs (1-min integration time) was conducted on 22 October 2009 to examine the detection sensitivity of the Co2DiaWiL. The achieved precision was less than 2.1%. The root-mean-square of the differences between the 30-min CO2 averages measured by the Co2DiaWiL and a ground-based in situ instrument was 0.9% (3.5 ppm). Experimental vertical CO2 measurements were conducted in February 2010 and January and February 2011. The partial CO2 column-averaged dry-air mixing ratios (XCO2) for an altitude between 0.4 and 1.0 km in 2010 and 2011 were 403.2 ± 4.2 and 405.6 ± 3.4 ppm, respectively. In the paper, the Co2DiaWiL results were well validated carefully against those of the airborne in situ instrument; they agreed well within the margin of error. The values of XCO2 measured in presence of cirrus clouds near the tropopause (hard target cases) show a difference of less than 4.1 ppm with the airborne measurements performed on 14 February 2010. This result demonstrates the capability of the Co2DiaWiL to measure XCO2 within a precision better than 1%.


  • Dual‐Doppler lidar observation of horizontal convective rolls and near‐surface streaks

    by Hironori Iwai, Shoken Ishii, Nobumitsu Tsunematsu, Kohei Mizutani, Yasuhiro Murayama, Toshikazu Itabe, Izumi Yamada, Naoki Matayoshi, Dai Matsushima, Sha Weiming, et al.

    Dual‐Doppler lidar and heliborne sensors were used to investigate the three‐dimensional (3D) structure of the wind field over Sendai Airport in June 2007. The 3D structures of several‐hundred‐meter‐scale horizontal convective rolls (HCRs) in the sea‐breeze layer were observed by the dual‐Doppler lidar. The scale of the HCRs determined by the heliborne sensors roughly agreed with that determined by the dual‐Doppler lidar. Analysis of the dual‐Doppler lidar data showed that the region of upward flow in the HCRs originated in near‐surface low‐speed streaks. This structure is consistent with the results of large‐eddy simulations of the atmospheric boundary layer. The aspect ratios of the HCRs were close to those predicted by linear theories.