Harold Krikke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Harold Krikke has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
Erwin van der Laan
Department of Decision and Information Sciences , RSM Erasmus University , PO Box 1738, 3000 DR, Rotterdam, The Netherlands
2 shared publications- Hein Fleuren
Tilburg University
2 shared publications - Ieke le Blanc
CentER Applied Research, Tilburg University, Tilburg, The Netherlands
2 shared publications H. M.
1 shared publication- Maaike van Krieken
CentER Applied Research, Tilburg University, Tilburg, The Netherlands
1 shared publication
Latest Publications
- 1 September 2011
- Published by Taylor & Francis in International Journal of Production Research
- Vol. 49 (17) , 5183-5206
Last Time Buy and control policies with phase-out returns: a case study in plant control systems
This research involves the combination of spare parts management and reverse logistics. At the end of the product life cycle, products in the field (so called installed base) can usually be serviced by either new parts, obtained from a Last Time Buy, or by repaired failed parts. This article, however, introduces a third source: the phase-out returns obtained from customers that replace systems. These returned parts may serve other customers that do not replace the systems yet. Phase-out return flows represent higher volumes and higher repair yields than failed parts and are cheaper to get than new ones. This new phenomenon has been ignored in the literature thus far, but due to increased product replacements rates its relevance will grow. We present a generic model, applied in a case study with real-life data from ConRepair, a third-party service provider in plant control systems (mainframes). Volumes of demand for spares, defect returns and phase-out returns are interrelated, because the same installed base is involved. In contrast with the existing literature, this article explicitly models the operational control of both failed- and phase-out returns, which proves far from trivial given the non-stationary nature of the problem. We have to consider subintervals within the total planning interval to optimise both Last Time Buy and control policies well. Given the novelty of the problem, we limit ourselves to a single customer, single-item approach. Our heuristic solution methods prove to be efficient and close to optimal when validated. The resulting control policies in the case study are also counter-intuitive. Contrary to (management) expectations, exogenous variables prove to be more important to the repair firm (which we show by sensitivity analysis) and optimising the endogenous control policy benefits the customers. Last Time Buy volume does not make the decisive difference; far more important is the disposal versus repair policy. PUSH control policy is outperformed by PULL, which exploits demand information and waits longer to decide between repair and disposal. The article concludes by mapping a number of extensions for future research, as it represents a larger class of problems.
- 1 September 2011
- Published by Taylor & Francis in International Journal of Production Research
- Vol. 49 (17) , 5183-5206
Last Time Buy and control policies with phase-out returns: a case study in plant control systems
This research involves the combination of spare parts management and reverse logistics. At the end of the product life cycle, products in the field (so called installed base) can usually be serviced by either new parts, obtained from a Last Time Buy, or by repaired failed parts. This article, however, introduces a third source: the phase-out returns obtained from customers that replace systems. These returned parts may serve other customers that do not replace the systems yet. Phase-out return flows represent higher volumes and higher repair yields than failed parts and are cheaper to get than new ones. This new phenomenon has been ignored in the literature thus far, but due to increased product replacements rates its relevance will grow. We present a generic model, applied in a case study with real-life data from ConRepair, a third-party service provider in plant control systems (mainframes). Volumes of demand for spares, defect returns and phase-out returns are interrelated, because the same installed base is involved. In contrast with the existing literature, this article explicitly models the operational control of both failed- and phase-out returns, which proves far from trivial given the non-stationary nature of the problem. We have to consider subintervals within the total planning interval to optimise both Last Time Buy and control policies well. Given the novelty of the problem, we limit ourselves to a single customer, single-item approach. Our heuristic solution methods prove to be efficient and close to optimal when validated. The resulting control policies in the case study are also counter-intuitive. Contrary to (management) expectations, exogenous variables prove to be more important to the repair firm (which we show by sensitivity analysis) and optimising the endogenous control policy benefits the customers. Last Time Buy volume does not make the decisive difference; far more important is the disposal versus repair policy. PUSH control policy is outperformed by PULL, which exploits demand information and waits longer to decide between repair and disposal. The article concludes by mapping a number of extensions for future research, as it represents a larger class of problems.
- Open Access
- 9 July 2010
- Published by Springer Nature in The International Journal of Life Cycle Assessment
- Vol. 15 (8) , 757-768
Opportunistic versus life-cycle-oriented decision making in multi-loop recovery: an eco-eco study on disposed vehicles
- 9 July 2010
- Published by Springer Nature in The International Journal of Life Cycle Assessment
- Vol. 15 (8) , 757-768
Open AccessOpportunistic versus life-cycle-oriented decision making in multi-loop recovery: an eco-eco study on disposed vehicles
- 29 January 2010
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 47 (5-8) , 413-414
International journal of advanced manufacturing technology introduction to the special issue
- 29 January 2010
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 47 (5-8) , 413-414
International journal of advanced manufacturing technology introduction to the special issue
- 17 November 2005
- Published by Springer Nature in OR Spectrum
- Vol. 28 (1) , 53-71
Vehicle routing concepts in the closed-loop container network of ARN—a case study
- 17 November 2005
- Published by Springer Nature in OR Spectrum
- Vol. 28 (1) , 53-71
Vehicle routing concepts in the closed-loop container network of ARN—a case study
- 1 March 2004
- Published by Springer Nature in OR Spectrum
- Vol. 26 (2) , 283-304
Redesign of a recycling system for LPG-tanks
- 1 March 2004
- Published by Springer Nature in OR Spectrum
- Vol. 26 (2) , 283-304
Redesign of a recycling system for LPG-tanks