Yasuo Terasawa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yasuo Terasawa has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Hiroyuki Tashiro
Division of Medical Technology, Department of Health Sciences, Faculty of Medical Sciences, Kyushu University
4 shared publications- Jun Ohta
Nara Institute of Science and Technology
3 shared publications Jun Ohta
Division of Materials Science, Nara Institute of Science and Technology
2 shared publicationsYukari Nakano
Nidek Co Ltd, Artificial Vis Inst, R&D Div, 13-2 Hama Cho, Gamagori, Aichi 4430036, Japan
2 shared publicationsAkihiro Uehara
Nidek Co, Ltd
1 shared publication- Kiyotaka Sasagawa
Division of Materials Science, Graduate School of Science and Technology, Nara Institute of Science and Technology, 8916-5 Takayama, Ikoma 630-0192, Nara, Japan
1 shared publication
Latest Publications
- Open Access
- 15 May 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (5) , 580
Development and Evaluation of Multi-Module Retinal Devices for Artificial Vision Applications
Artificial retinal devices require a high-density electrode array and mechanical flexibility to effectively stimulate retinal cells. However, designing such devices presents significant challenges, including the need to conform to the curvature of the eyeball and cover a large area using a single platform. To address these issues, we developed a parylene-based multi-module retinal device (MMRD) integrating a complementary metal-oxide semiconductor (CMOS) system. The proposed device is designed for suprachoroidal transretinal stimulation, with each module comprising a parylene-C thin-film substrate, a CMOS chip, and a ceramic substrate housing seven platinum electrodes. The smart CMOS system significantly reduces wiring complexity, enhancing the device’s practicality. To improve fabrication reliability, we optimized the encapsulation process, introduced multiple silane coupling modifications, and utilized polyvinyl alcohol (PVA) for easier detachment in flip-chip bonding. This study demonstrates the fabrication and evaluation of the MMRD through in vitro and in vivo experiments. The device successfully generated the expected current stimulation waveforms in both settings, highlighting its potential as a promising candidate for future artificial vision applications.
- 15 May 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (5) , 580
Open AccessDevelopment and Evaluation of Multi-Module Retinal Devices for Artificial Vision Applications
Artificial retinal devices require a high-density electrode array and mechanical flexibility to effectively stimulate retinal cells. However, designing such devices presents significant challenges, including the need to conform to the curvature of the eyeball and cover a large area using a single platform. To address these issues, we developed a parylene-based multi-module retinal device (MMRD) integrating a complementary metal-oxide semiconductor (CMOS) system. The proposed device is designed for suprachoroidal transretinal stimulation, with each module comprising a parylene-C thin-film substrate, a CMOS chip, and a ceramic substrate housing seven platinum electrodes. The smart CMOS system significantly reduces wiring complexity, enhancing the device’s practicality. To improve fabrication reliability, we optimized the encapsulation process, introduced multiple silane coupling modifications, and utilized polyvinyl alcohol (PVA) for easier detachment in flip-chip bonding. This study demonstrates the fabrication and evaluation of the MMRD through in vitro and in vivo experiments. The device successfully generated the expected current stimulation waveforms in both settings, highlighting its potential as a promising candidate for future artificial vision applications.
- Open Access
- 1 January 2024
- Published by Japanese Society for Medical and Biological Engineering in Advanced Biomedical Engineering
- Vol. 13, 108-115
Development of Flexible Multilayer Circuit Board Fabrication Technology by Combining Laser Micromachining with Platinum Foil and Microwelding for Biomedical Applications
Implantable devices utilize flexible substrates due to their ability to conform to the complex shapes and movements of living organisms. However, these devices have a limit to the available power and necessitate low-resistance wiring to handle the extra power consumed on the substrate side. Moreover, complex wiring technology with multilayer wiring is essential to enhance the functionality of implantable devices. Previous studies primarily employed sputtering and printing methods for the fabrication of flexible substrate wiring. However, the wiring resistance is tens to hundreds Ω, causing large power loss. In this study, we aimed to create flexible, low-resistance multilayer circuit boards with resistance less than 1 Ω for implantable devices. Polydimethylsiloxane was used as the substrate material, while platinum was used as the wiring material. The wiring pattern was formed by laser micromachining using an ultrashort pulse laser, and interlayer connections were achieved using Pt Vias fabricated by microwelding. The multilayer circuit board fabricated low impedance wires of 0.25 Ω or less. Furthermore, the wiring demonstrated excellent insulation between wires, even after a 3-hour exposure test in a simulated biological environment, with no short-circuiting issues. Regarding mechanical properties, no significant changes were observed after subjecting the circuit boards to 500 cycles of repeated bending in a bending test with a 6-mm radius. In conclusion, these results indicate that the flexible multilayer circuit boards are well suited for various implantable devices that require low resistance.
- 1 January 2024
- Published by Japanese Society for Medical and Biological Engineering in Advanced Biomedical Engineering
- Vol. 13, 108-115
Open AccessDevelopment of Flexible Multilayer Circuit Board Fabrication Technology by Combining Laser Micromachining with Platinum Foil and Microwelding for Biomedical Applications
Implantable devices utilize flexible substrates due to their ability to conform to the complex shapes and movements of living organisms. However, these devices have a limit to the available power and necessitate low-resistance wiring to handle the extra power consumed on the substrate side. Moreover, complex wiring technology with multilayer wiring is essential to enhance the functionality of implantable devices. Previous studies primarily employed sputtering and printing methods for the fabrication of flexible substrate wiring. However, the wiring resistance is tens to hundreds Ω, causing large power loss. In this study, we aimed to create flexible, low-resistance multilayer circuit boards with resistance less than 1 Ω for implantable devices. Polydimethylsiloxane was used as the substrate material, while platinum was used as the wiring material. The wiring pattern was formed by laser micromachining using an ultrashort pulse laser, and interlayer connections were achieved using Pt Vias fabricated by microwelding. The multilayer circuit board fabricated low impedance wires of 0.25 Ω or less. Furthermore, the wiring demonstrated excellent insulation between wires, even after a 3-hour exposure test in a simulated biological environment, with no short-circuiting issues. Regarding mechanical properties, no significant changes were observed after subjecting the circuit boards to 500 cycles of repeated bending in a bending test with a 6-mm radius. In conclusion, these results indicate that the flexible multilayer circuit boards are well suited for various implantable devices that require low resistance.
- Open Access
- 18 June 2019
- Published by MYU K.K. in Sensors and Materials
- Vol. 31 (6) , 1957-1971
Porosification of Surface of Platinum Electrode by Anisotropic Etching
- 18 June 2019
- Published by MYU K.K. in Sensors and Materials
- Vol. 31 (6) , 1957-1971
Open AccessPorosification of Surface of Platinum Electrode by Anisotropic Etching
- Open Access
- 1 January 2018
- Published by MYU K.K. in Sensors and Materials
- Vol. 30 (2) , 235-249
Safety and Efficacy of Semichronic Suprachoroidal Transretinal Stimulation with Femtosecond Laser-induced Porosity and Smooth-surface Electrodes
- 1 January 2018
- Published by MYU K.K. in Sensors and Materials
- Vol. 30 (2) , 235-249
Open AccessSafety and Efficacy of Semichronic Suprachoroidal Transretinal Stimulation with Femtosecond Laser-induced Porosity and Smooth-surface Electrodes
- 21 December 2006
- Published by Springer Nature in Journal of Artificial Organs
- Vol. 9 (4) , 263-266
The development of a multichannel electrode array for retinal prostheses
The development of a multielectrode array is the key issue for retinal prostheses. We developed a 10 × 10 platinum electrode array that consists of an 8-µm polyimide layer sandwiched between 5-µm polymonochloro-para-xylylene (parylene-C) layers. Each electrode was formed as a 30-µm-high bump by Pt/Au double-layer electroplating. We estimated the charge delivery capability (CDC) of the electrode by measuring the CDCs of two-channel electrode arrays. The dimensions of each electrode of the two-channel array were the same as those of each electrode formed on the 10 × 10 array. The results suggest that for cathodic-first (CF) pulses, 80% of electrodes surpassed our development target of 318 µC/cm2, which corresponds to the charge density of pulses of 500 µs duration and 200 µA amplitude for a 200-µm-diameter planar electrode.
- 21 December 2006
- Published by Springer Nature in Journal of Artificial Organs
- Vol. 9 (4) , 263-266
The development of a multichannel electrode array for retinal prostheses
The development of a multielectrode array is the key issue for retinal prostheses. We developed a 10 × 10 platinum electrode array that consists of an 8-µm polyimide layer sandwiched between 5-µm polymonochloro-para-xylylene (parylene-C) layers. Each electrode was formed as a 30-µm-high bump by Pt/Au double-layer electroplating. We estimated the charge delivery capability (CDC) of the electrode by measuring the CDCs of two-channel electrode arrays. The dimensions of each electrode of the two-channel array were the same as those of each electrode formed on the 10 × 10 array. The results suggest that for cathodic-first (CF) pulses, 80% of electrodes surpassed our development target of 318 µC/cm2, which corresponds to the charge density of pulses of 500 µs duration and 200 µA amplitude for a 200-µm-diameter planar electrode.