Takashi Ueda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Takashi Ueda has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Akira Hosokawa
Faculty of Production Systems Engineering and Sciences, Komatsu University
9 shared publications - Tatsuaki Furumoto
Advanced Manufacturing Technology Institute (AMTI), Kanazawa University, Kakuma-machi, Kanazawa, Ishikawa 920-1192, Japan
7 shared publications - Ryutaro Tanaka
Graduate School of Advanced Science and Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8527, Japan
4 shared publications - Keiji Yamada
Graduate School of Advanced Science and Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8527, Japan
3 shared publications Akira Hosokawa
Kanazawa Univ, Adv Mfg Technol Inst, Kanazawa, Ishikawa, Japan
2 shared publicationsA. Hosokawa
Faculty of Mechanical Engineering, Institute of Science and Engineering, Kanazawa University, Kakuma-machi, Kanazawa, Ishikawa 920-1192, Japan
1 shared publication
Latest Publications
- Open Access
- 19 May 2022
- Published by Elsevier in CIRP Annals
- Vol. 71 (1) , 81-84
Turning characteristics of titanium alloy Ti-6Al-4V with high-pressure cutting fluid
- 19 May 2022
- Published by Elsevier in CIRP Annals
- Vol. 71 (1) , 81-84
Open AccessTurning characteristics of titanium alloy Ti-6Al-4V with high-pressure cutting fluid
- 1 January 2020
- Published by Elsevier in CIRP Annals
- Vol. 69 (1) , 49-52
Milling characteristics of VN/AlCrN-multilayer PVD coated tools with lubricity and heat resistance
- 1 January 2020
- Published by Elsevier in CIRP Annals
- Vol. 69 (1) , 49-52
Milling characteristics of VN/AlCrN-multilayer PVD coated tools with lubricity and heat resistance
- Open Access
- 1 January 2013
- Published by Japan Society of Mechanical Engineers in Journal of Advanced Mechanical Design, Systems, and Manufacturing
- Vol. 7 (2) , 244-256
Residual Stress and Deformation of Consolidated Structure Obtained by Layered Manufacturing Process
- 1 January 2013
- Published by Japan Society of Mechanical Engineers in Journal of Advanced Mechanical Design, Systems, and Manufacturing
- Vol. 7 (2) , 244-256
Open AccessResidual Stress and Deformation of Consolidated Structure Obtained by Layered Manufacturing Process
- Open Access
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2012, _S131022-1
S131022 Study on Air Vent Structure in Injection Mold Manufactured by Rapid Tooling System
Recently, the complicated shape molds can be manufactured at a shorter production time and lower cost by rapid tooling (RT) technology. Additionally, in injection molding, the air vent system using porous material is known as effective way to exhaust gas pressed into mold and improve the burning and short shot of molded components. Thereat, applying that air vent system to injection molds manufactured by RT technique is now expected. In this report, the fabrication of air vent structure which is obtained by an additive manufacturing system is proposed. The influence of laser conditions on the porosity and the permeability of the consolidated structure are investigated experimentally. As a result, the porosity and permeability are increased relative to laser scan speed. The porous part of sintered structure becomes permeable over 25% of the porosity.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2012, _S131022-1
Open AccessS131022 Study on Air Vent Structure in Injection Mold Manufactured by Rapid Tooling System
Recently, the complicated shape molds can be manufactured at a shorter production time and lower cost by rapid tooling (RT) technology. Additionally, in injection molding, the air vent system using porous material is known as effective way to exhaust gas pressed into mold and improve the burning and short shot of molded components. Thereat, applying that air vent system to injection molds manufactured by RT technique is now expected. In this report, the fabrication of air vent structure which is obtained by an additive manufacturing system is proposed. The influence of laser conditions on the porosity and the permeability of the consolidated structure are investigated experimentally. As a result, the porosity and permeability are increased relative to laser scan speed. The porous part of sintered structure becomes permeable over 25% of the porosity.
- Open Access
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Hokuriku-Shinetsu Branch
- Vol. 2012.49, 101801-101802
1018 Cutting Performance of Ceramic Tools in Turning of Mild Carbon Steel : Evaluation of Applicability for BN Added Steel
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Hokuriku-Shinetsu Branch
- Vol. 2012.49, 101801-101802
Open Access1018 Cutting Performance of Ceramic Tools in Turning of Mild Carbon Steel : Evaluation of Applicability for BN Added Steel
- Open Access
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Hokuriku-Shinetsu Branch
- Vol. 2012.49, 101901-101902
1019 Influence of tool edge temperature on surface quality in turning of sintered steel
Influence of tool edge temperature
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Hokuriku-Shinetsu Branch
- Vol. 2012.49, 101901-101902
Open Access1019 Influence of tool edge temperature on surface quality in turning of sintered steel
Influence of tool edge temperature
- 31 December 2011
- Published by Elsevier in CIRP Annals
- Vol. 60 (1) , 555-558
Surface temperature during cavity preparation on human tooth by Er:YAG laser irradiation
- 31 December 2011
- Published by Elsevier in CIRP Annals
- Vol. 60 (1) , 555-558
Surface temperature during cavity preparation on human tooth by Er:YAG laser irradiation
- 1 January 2010
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 24 (1) , 77-80
Study on tool wear mechanisms in milling laser sintered material
- 1 January 2010
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 24 (1) , 77-80
Study on tool wear mechanisms in milling laser sintered material
- 1 January 2009
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 407-409, 690-693
Influence of On-the-Machine Laser Hardening on Machinability of Carbon Steel in Turning
- 1 January 2009
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 407-409, 690-693
Influence of On-the-Machine Laser Hardening on Machinability of Carbon Steel in Turning