Julie Diani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Julie Diani has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
A. M. Ortega
Deparment of Mechanical Engineering, University of Colorado, Boulder, Colorado 80309
1 shared publicationA. R. Greenberg
Deparment of Mechanical Engineering, University of Colorado, Boulder, Colorado 80309
1 shared publicationB. Fayolle
Laboratoire d'Ingénierie des Matériaux , CNRS, Arts et Métiers ParisTech, Paris, France
1 shared publicationK. Gall
School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332
1 shared publicationKen Gall
School of Materials Science and Engineering and George Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332
1 shared publicationP. Gilormini
Laboratoire d'Ingénierie des Matériaux , CNRS, Arts et Métiers ParisTech, Paris, France
1 shared publication
Latest Publications
- 1 March 2017
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 173, 32-40
Some features of the PPR cohesive-zone model combined with a linear unloading/reloading relationship
- 1 March 2017
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 173, 32-40
Some features of the PPR cohesive-zone model combined with a linear unloading/reloading relationship
- 1 September 2008
- Published by Taylor & Francis in Molecular Simulation
- Vol. 34 (10-15) , 1143-1148
Study on the temperature dependence of the bulk modulus of polyisoprene by molecular dynamics simulations
The temperature dependence of the bulk modulus of polyisoprene has been studied using molecular dynamics simulations. Virtual polyisoprenes have been submitted to volume contractions above and below the glass transition. Bulk modulus has been observed to be linearly dependent on temperature both above and below the glass transition respectively, and it dropped by a factor of about 2 while temperature was raised above the glass transition. By monitoring the energy changes during volume contractions, it was observed that the bulk modulus arises mainly from the Van der Waals interactions. Nevertheless, the entropy contribution to the bulk modulus becomes significant above the glass transition. At a first order, the entropy part of the bulk modulus can be considered as independent of the temperature.
- 1 September 2008
- Published by Taylor & Francis in Molecular Simulation
- Vol. 34 (10-15) , 1143-1148
Study on the temperature dependence of the bulk modulus of polyisoprene by molecular dynamics simulations
The temperature dependence of the bulk modulus of polyisoprene has been studied using molecular dynamics simulations. Virtual polyisoprenes have been submitted to volume contractions above and below the glass transition. Bulk modulus has been observed to be linearly dependent on temperature both above and below the glass transition respectively, and it dropped by a factor of about 2 while temperature was raised above the glass transition. By monitoring the energy changes during volume contractions, it was observed that the bulk modulus arises mainly from the Van der Waals interactions. Nevertheless, the entropy contribution to the bulk modulus becomes significant above the glass transition. At a first order, the entropy part of the bulk modulus can be considered as independent of the temperature.
- 8 May 2008
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 46 (12) , 1226-1234
On the relevance of the 8‐chain model and the full‐network model for the deformation and failure of networks formed through photopolymerization of multifunctional monomers
Crosslinked networks were synthesized by copolymerization of mono‐functional tert‐butyl acrylate (tBA) with diethyleneglycol dimethacrylate (DEGDMA) or polyethylene glycol dimethacrylates (PEGDMA). By varying the chain length and concentration of the difunctional PEGDMA, we obtained tBA‐PEGDMA copolymer networks while by varying the concentration of difunctional DEGDMA, we obtained tBA‐DEGDMA crosslinked networks. The various materials were submitted to large deformations through uniaxial tension tests. For moderate weight percent of crosslinking agent, up to 20%, the networks showed standard S‐shape stress–strain curves, characteristic of rubber‐like elasticity. Two macromolecular models, the 8‐chain model and the full‐network model, were applied to fit the uniaxial tensile response of the materials. Both models provide good representations of the overall uniaxial stress–strain response of each material. After fitting to stress–strain data, the network models were employed to predict the shear modulus and the elongation at break. Neither the 8‐chain nor the full network model were capable of predicting the failure strain or shear modulus, indicating these models are best used to describe stress–strain relations rather than predict mechanical properties for the network polymers considered here. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1226–1234, 2008
- 8 May 2008
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 46 (12) , 1226-1234
On the relevance of the 8‐chain model and the full‐network model for the deformation and failure of networks formed through photopolymerization of multifunctional monomers
Crosslinked networks were synthesized by copolymerization of mono‐functional tert‐butyl acrylate (tBA) with diethyleneglycol dimethacrylate (DEGDMA) or polyethylene glycol dimethacrylates (PEGDMA). By varying the chain length and concentration of the difunctional PEGDMA, we obtained tBA‐PEGDMA copolymer networks while by varying the concentration of difunctional DEGDMA, we obtained tBA‐DEGDMA crosslinked networks. The various materials were submitted to large deformations through uniaxial tension tests. For moderate weight percent of crosslinking agent, up to 20%, the networks showed standard S‐shape stress–strain curves, characteristic of rubber‐like elasticity. Two macromolecular models, the 8‐chain model and the full‐network model, were applied to fit the uniaxial tensile response of the materials. Both models provide good representations of the overall uniaxial stress–strain response of each material. After fitting to stress–strain data, the network models were employed to predict the shear modulus and the elongation at break. Neither the 8‐chain nor the full network model were capable of predicting the failure strain or shear modulus, indicating these models are best used to describe stress–strain relations rather than predict mechanical properties for the network polymers considered here. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1226–1234, 2008
- 22 February 2006
- Published by Wiley in Polymer Engineering & Science
- Vol. 46 (4) , 486-492
Finite strain 3D thermoviscoelastic constitutive model for shape memory polymers
A 3D thermoviscoelastic model is proposed to represent the thermomechanical behavior of shape memory polymers. The model is based on a physical understanding of the material behavior and a mechanical interpretation of the stress–strain–temperature changes observed during thermomechanical loading. The model is thermodynamically motivated and is formulated in a finite strain framework in order to account for large strain deformations. Model predictions capture critical features of shape memory polymer deformation and, in some cases, provide very favorable comparisons with experimental results. POLYM. ENG. SCI. 46:486–492, 2006. © 2006 Society of Plastics Engineers.
- 22 February 2006
- Published by Wiley in Polymer Engineering & Science
- Vol. 46 (4) , 486-492
Finite strain 3D thermoviscoelastic constitutive model for shape memory polymers
A 3D thermoviscoelastic model is proposed to represent the thermomechanical behavior of shape memory polymers. The model is based on a physical understanding of the material behavior and a mechanical interpretation of the stress–strain–temperature changes observed during thermomechanical loading. The model is thermodynamically motivated and is formulated in a finite strain framework in order to account for large strain deformations. Model predictions capture critical features of shape memory polymer deformation and, in some cases, provide very favorable comparisons with experimental results. POLYM. ENG. SCI. 46:486–492, 2006. © 2006 Society of Plastics Engineers.
- 30 November 2005
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 53 (11) , 2579-2596
Combining the logarithmic strain and the full-network model for a better understanding of the hyperelastic behavior of rubber-like materials
- 30 November 2005
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 53 (11) , 2579-2596
Combining the logarithmic strain and the full-network model for a better understanding of the hyperelastic behavior of rubber-like materials