Ulf Jansson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ulf Jansson has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Chin Shen Ong
Uppsala University
2 shared publications - Erik Lewin
Uppsala University
2 shared publications - Johan Cedervall
Department of Chemistry, Ångström Laboratory, Uppsala University, Box 523, Uppsala, S-75120, Sweden
2 shared publications Lars Norin
Department of Inorganic Chemistry, Ångström Laboratory, Uppsala University, S-751 21, Uppsala, Sweden
2 shared publications- Olivier Donzel-Gargand
Uppsala University
2 shared publications - Pedro Berastegui
Department of Chemistry, Ångström Laboratory, Uppsala University, Box 523, Uppsala, S-75120, Sweden
2 shared publications
Latest Publications
- Open Access
- 22 April 2026
- Published by International Union of Crystallography (IUCr) in Acta crystallographica Section B, Structural science, crystal engineering and materials
- Vol. 82 (3) , 299-309
Unraveling the symmetry of Al 5 C 3 N
High-temperature ceramic compound Al 5 C 3 N belongs to the scarcely studied Al–C–N system. It was originally reported as an ordered compound in noncentrosymmetric space group P 6 3 mc and described as a nanolaminate with an –Al 2 C–AlN–Al 2 C 2 – stacking sequence. The recently reported structural disorder in the related compound Al 4 SiC 4 led us to question this proposed structure for Al 5 C 3 N and investigate the possibility of a disordered structure in the centrosymmetric space group P 6 3 / mmc . In the present work, we employed different synthesis routes to maximize the yield and quality of the desired phase, and applied a variety of techniques to probe the Al 5 C 3 N crystal structure. Our single-crystal X-ray diffraction analysis clearly indicates that noncentrosymmetric space group P 6 3 mc must be rejected. From a joint refinement of single-crystal X-ray and neutron powder diffraction data, the occupancies of C and N were refined at two sites in P 6 3 / mmc resulting in the stacking sequence –Al 2 C–Al(C/N)–Al 2 (C/N) 2 –. Furthermore, DFT calculations show that a centrosymmetric disordered structure described in a supercell has the lowest energy, 0.2 eV per formula unit, relative to the previously reported P 6 3 mc structure. The calculated band structure shows both direct and indirect bandgaps, which leads to implications for the physical properties. Finally, STEM analysis provides additional evidence that the crystal structure of Al 5 C 3 N is better described in centrosymmetric space group P 6 3 / mmc .
- 22 April 2026
- Published by International Union of Crystallography (IUCr) in Acta crystallographica Section B, Structural science, crystal engineering and materials
- Vol. 82 (3) , 299-309
Open AccessUnraveling the symmetry of Al 5 C 3 N
High-temperature ceramic compound Al 5 C 3 N belongs to the scarcely studied Al–C–N system. It was originally reported as an ordered compound in noncentrosymmetric space group P 6 3 mc and described as a nanolaminate with an –Al 2 C–AlN–Al 2 C 2 – stacking sequence. The recently reported structural disorder in the related compound Al 4 SiC 4 led us to question this proposed structure for Al 5 C 3 N and investigate the possibility of a disordered structure in the centrosymmetric space group P 6 3 / mmc . In the present work, we employed different synthesis routes to maximize the yield and quality of the desired phase, and applied a variety of techniques to probe the Al 5 C 3 N crystal structure. Our single-crystal X-ray diffraction analysis clearly indicates that noncentrosymmetric space group P 6 3 mc must be rejected. From a joint refinement of single-crystal X-ray and neutron powder diffraction data, the occupancies of C and N were refined at two sites in P 6 3 / mmc resulting in the stacking sequence –Al 2 C–Al(C/N)–Al 2 (C/N) 2 –. Furthermore, DFT calculations show that a centrosymmetric disordered structure described in a supercell has the lowest energy, 0.2 eV per formula unit, relative to the previously reported P 6 3 mc structure. The calculated band structure shows both direct and indirect bandgaps, which leads to implications for the physical properties. Finally, STEM analysis provides additional evidence that the crystal structure of Al 5 C 3 N is better described in centrosymmetric space group P 6 3 / mmc .
- Open Access
- 27 May 2024
- Published by American Chemical Society (ACS) in Inorganic Chemistry
- Vol. 63 (23) , 10490-10499
The Crystal Structure of Al4SiC4 Revisited
Al4SiC4 is a ternary wide-band-gap semiconductor with a high strength-to-weight ratio and excellent oxidation resistance. It consists of slabs of Al4C3 separated by SiC layers with the space group of P6(3)mc. The space group allows Si to occupy two different 2a Wykoff sites, with previous studies reporting that Si occupies only one of the two sites, giving it an ordered structure. Another hitherto unexplored possibility is that Si can be randomly distributed on both 2a sites. In this work, we revisit the published ordered crystal structure using experimental methods and density functional theory (DFT). Al4SiC4 was synthesized by high-temperature sintering at 1800 degrees C from a powder mixture of Al4C3 and SiC. Neutron diffraction confirmed that Al4SiC4 crystallized with the space group of P6(3)mc, with diffraction patterns that could be fitted to both the ordered and the disordered structures. Scanning transmission electron microscopy, however, provided clear evidence supporting the latter, with DFT calculations further confirming that it is 0.16 eV lower in energy per Al4SiC4 formula unit than the former. TEM analysis revealed Al vacancies in some of the atomic layers that can introduce p-type doping and direct band gaps of 0.7 and 1.2 eV, agreeing with our optical measurements. Finally, we propose that although the calculated formation energy of the Al vacancies is high, the vacancies are stabilized by entropy effects at the high synthesis temperature. This indicates that the cooling procedure after high-temperature synthesis can be important in determining the vacancy content and the electronic properties of Al4SiC4.
- 27 May 2024
- Published by American Chemical Society (ACS) in Inorganic Chemistry
- Vol. 63 (23) , 10490-10499
Open AccessThe Crystal Structure of Al4SiC4 Revisited
Al4SiC4 is a ternary wide-band-gap semiconductor with a high strength-to-weight ratio and excellent oxidation resistance. It consists of slabs of Al4C3 separated by SiC layers with the space group of P6(3)mc. The space group allows Si to occupy two different 2a Wykoff sites, with previous studies reporting that Si occupies only one of the two sites, giving it an ordered structure. Another hitherto unexplored possibility is that Si can be randomly distributed on both 2a sites. In this work, we revisit the published ordered crystal structure using experimental methods and density functional theory (DFT). Al4SiC4 was synthesized by high-temperature sintering at 1800 degrees C from a powder mixture of Al4C3 and SiC. Neutron diffraction confirmed that Al4SiC4 crystallized with the space group of P6(3)mc, with diffraction patterns that could be fitted to both the ordered and the disordered structures. Scanning transmission electron microscopy, however, provided clear evidence supporting the latter, with DFT calculations further confirming that it is 0.16 eV lower in energy per Al4SiC4 formula unit than the former. TEM analysis revealed Al vacancies in some of the atomic layers that can introduce p-type doping and direct band gaps of 0.7 and 1.2 eV, agreeing with our optical measurements. Finally, we propose that although the calculated formation energy of the Al vacancies is high, the vacancies are stabilized by entropy effects at the high synthesis temperature. This indicates that the cooling procedure after high-temperature synthesis can be important in determining the vacancy content and the electronic properties of Al4SiC4.
- Open Access
Additive Manufacturing of Cu Using Graphene-Oxide-Treated Powder
Additive manufacturing of Cu is interesting for many applications where high thermal and electric conductivity are required. A problem with printing of Cu with a laser-based process is the high reflectance of the powder for near-infrared wavelengths making it difficult to print components with a high density. In this study, we have investigated laser bed fusion (L-PBF) of Cu using graphene oxide (GO)-coated powder. The powder particles were coated in a simple wet-chemical process using electrostatic attractions between the GO and the powder surface. The coated powder exhibited a reduced reflectivity, which improved the printability and increased the densities from ~90% for uncoated powder to 99.8% using 0.1 wt% GO and a laser power of 500 W. The coated Cu powders showed a tendency for balling using laser powers below 400 W, and increasing the GO concentration from 0.1 to 0.3 wt.% showed an increase in spattering and reduced density. Graphene-like sheet structures could be observed in the printed parts using scanning electron microscopy (SEM). Carbon-filled inclusions with sizes ranging from 10–200 nm could also be observed in the printed parts using transmission electron microscopy (TEM). The GO treatment yielded parts with higher hardness (75.7 HV) and electrical conductivity (77.8% IACS) compared to the parts printed with reference Cu powder.
Open AccessAdditive Manufacturing of Cu Using Graphene-Oxide-Treated Powder
Additive manufacturing of Cu is interesting for many applications where high thermal and electric conductivity are required. A problem with printing of Cu with a laser-based process is the high reflectance of the powder for near-infrared wavelengths making it difficult to print components with a high density. In this study, we have investigated laser bed fusion (L-PBF) of Cu using graphene oxide (GO)-coated powder. The powder particles were coated in a simple wet-chemical process using electrostatic attractions between the GO and the powder surface. The coated powder exhibited a reduced reflectivity, which improved the printability and increased the densities from ~90% for uncoated powder to 99.8% using 0.1 wt% GO and a laser power of 500 W. The coated Cu powders showed a tendency for balling using laser powers below 400 W, and increasing the GO concentration from 0.1 to 0.3 wt.% showed an increase in spattering and reduced density. Graphene-like sheet structures could be observed in the printed parts using scanning electron microscopy (SEM). Carbon-filled inclusions with sizes ranging from 10–200 nm could also be observed in the printed parts using transmission electron microscopy (TEM). The GO treatment yielded parts with higher hardness (75.7 HV) and electrical conductivity (77.8% IACS) compared to the parts printed with reference Cu powder.
- Open Access
Convective Flow Redistribution of Oxygen by Laser Melting of a Zr-Based Amorphous Alloy
Oxygen impurities play a crucial role in the glass-forming ability and crystallisation behaviour of metallic glasses. In the present work, single laser tracks were produced on Zr59.3-xCu28.8 Al10.4Nb1.5Ox substrates (x = 0.3, 1.3) to study the redistribution of oxygen in the melt pool under laser melting, which provides the basis for laser powder bed fusion additive manufacturing. Since such substrates are commercially not available, they were fabricated by arc melting and splat quenching. X-ray diffraction revealed that the substrate with 0.3 at.% oxygen was X-ray amorphous, while the substrate with 1.3 at.% oxygen was partially crystalline. Hence, it is evident that the oxygen content affects the crystallisation kinetics. Subsequently, single laser tracks were produced on the surface of these substrates, and the melt pools attained from the laser processing were characterised by atom probe tomography and transmission electron microscopy. Surface oxidation and subsequent convective flow redistribution of oxygen by laser melting were identified as causes of the presence of CuOx and crystalline ZrO nanoparticles in the melt pool. Bands of ZrO likely originate from surface oxides that were moved deeper into the melt pool by convective flow. The findings presented here highlight the influence of oxygen redistribution from the surface into the melt pool during laser processing.
Open AccessConvective Flow Redistribution of Oxygen by Laser Melting of a Zr-Based Amorphous Alloy
Oxygen impurities play a crucial role in the glass-forming ability and crystallisation behaviour of metallic glasses. In the present work, single laser tracks were produced on Zr59.3-xCu28.8 Al10.4Nb1.5Ox substrates (x = 0.3, 1.3) to study the redistribution of oxygen in the melt pool under laser melting, which provides the basis for laser powder bed fusion additive manufacturing. Since such substrates are commercially not available, they were fabricated by arc melting and splat quenching. X-ray diffraction revealed that the substrate with 0.3 at.% oxygen was X-ray amorphous, while the substrate with 1.3 at.% oxygen was partially crystalline. Hence, it is evident that the oxygen content affects the crystallisation kinetics. Subsequently, single laser tracks were produced on the surface of these substrates, and the melt pools attained from the laser processing were characterised by atom probe tomography and transmission electron microscopy. Surface oxidation and subsequent convective flow redistribution of oxygen by laser melting were identified as causes of the presence of CuOx and crystalline ZrO nanoparticles in the melt pool. Bands of ZrO likely originate from surface oxides that were moved deeper into the melt pool by convective flow. The findings presented here highlight the influence of oxygen redistribution from the surface into the melt pool during laser processing.
- Open Access
Relationship between Microstructure, Mechanical Properties and Creep Behavior of a Cr-Rich Ferritic Stainless Steel Produced by Laser Powder Bed Fusion
Additive manufacturing (AM) techniques such as laser powder bed fusion (L-PBF) are rapidly growing due to the inherent design freedom and possibilities to produce components not available with other techniques. This could be utilized in, e.g., the design of new types of heat exchangers in ferritic stainless steels often used for high-temperature applications. Ferritic stainless steels are, however, difficult to weld and could therefore imply obstacles when produced by AM. When establishing the AM-produced alloy in new applications, it is therefore important to increase the understanding of the mechanical properties and high-temperature creep resistance in relation to the unique microstructure and printability. In this study, we have investigated the microstructure of Cr-rich SS446 ferritic stainless steel produced by L-PBF by microscopical and crystallographic techniques. The properties were compared to the conventionally produced tubes. The rapid cooling and reheating during the application of the subsequent powder layers during L-PBF introduces an intriguing microstructure consisting of a ferritic matrix with precipitation of austenite showing a Kurdjumov–Sachs orientation relationship. Characteristic dislocation networks were observed in the L-PBF samples and contributed to the good mechanical properties in the as-built state (more than twice the yield strength of the conventionally produced tube). Furthermore, the creep resistance at 800 °C was superior to the conventionally produced component, suggesting that L-PBF-produced SS446 possesses many advantages regarding production as compared to the conventional route.
Open AccessRelationship between Microstructure, Mechanical Properties and Creep Behavior of a Cr-Rich Ferritic Stainless Steel Produced by Laser Powder Bed Fusion
Additive manufacturing (AM) techniques such as laser powder bed fusion (L-PBF) are rapidly growing due to the inherent design freedom and possibilities to produce components not available with other techniques. This could be utilized in, e.g., the design of new types of heat exchangers in ferritic stainless steels often used for high-temperature applications. Ferritic stainless steels are, however, difficult to weld and could therefore imply obstacles when produced by AM. When establishing the AM-produced alloy in new applications, it is therefore important to increase the understanding of the mechanical properties and high-temperature creep resistance in relation to the unique microstructure and printability. In this study, we have investigated the microstructure of Cr-rich SS446 ferritic stainless steel produced by L-PBF by microscopical and crystallographic techniques. The properties were compared to the conventionally produced tubes. The rapid cooling and reheating during the application of the subsequent powder layers during L-PBF introduces an intriguing microstructure consisting of a ferritic matrix with precipitation of austenite showing a Kurdjumov–Sachs orientation relationship. Characteristic dislocation networks were observed in the L-PBF samples and contributed to the good mechanical properties in the as-built state (more than twice the yield strength of the conventionally produced tube). Furthermore, the creep resistance at 800 °C was superior to the conventionally produced component, suggesting that L-PBF-produced SS446 possesses many advantages regarding production as compared to the conventional route.
- Open Access
Synthesis and Characterisation of Nanocomposite Mo-Fe-B Thin Films Deposited by Magnetron Sputtering
Several ternary phases are known in the Mo-Fe-B system. Previous ab initio calculations have predicted that they should exhibit a tempting mix of mechanical and magnetic properties. In this study, we have deposited Mo-Fe-B films with a Fe-content varying from 0–37 at.% using non-reactive DC (direct current) magnetron sputtering. The phase composition, microstructure, and mechanical properties were investigated using X-ray diffraction, scanning transmission electron microscopy, and nanoindentation measurements. Films deposited at 300 °C and with >7 at.% Fe are nanocomposites consisting of two amorphous phases: a metal-rich phase and a metal-deficient phase. Hardness and elastic modulus were reduced with increasing Fe-content from ~29 to ~19 GPa and ~526 to ~353 GPa, respectively. These values result in H3/E2 ratios of 0.089–0.052 GPa, thereby indicating brittle behaviour of the films. Also, no indication of crystalline ternary phases was observed at temperatures up to 600 °C, suggesting that higher temperatures are required for such films to form.
Open AccessSynthesis and Characterisation of Nanocomposite Mo-Fe-B Thin Films Deposited by Magnetron Sputtering
Several ternary phases are known in the Mo-Fe-B system. Previous ab initio calculations have predicted that they should exhibit a tempting mix of mechanical and magnetic properties. In this study, we have deposited Mo-Fe-B films with a Fe-content varying from 0–37 at.% using non-reactive DC (direct current) magnetron sputtering. The phase composition, microstructure, and mechanical properties were investigated using X-ray diffraction, scanning transmission electron microscopy, and nanoindentation measurements. Films deposited at 300 °C and with >7 at.% Fe are nanocomposites consisting of two amorphous phases: a metal-rich phase and a metal-deficient phase. Hardness and elastic modulus were reduced with increasing Fe-content from ~29 to ~19 GPa and ~526 to ~353 GPa, respectively. These values result in H3/E2 ratios of 0.089–0.052 GPa, thereby indicating brittle behaviour of the films. Also, no indication of crystalline ternary phases was observed at temperatures up to 600 °C, suggesting that higher temperatures are required for such films to form.
- Open Access
Magnetron Sputtering of Nanolaminated Cr2AlB2
A ternary Cr2AlB2 phase was deposited as a film using magnetron sputtering. Its anisotropic structure displays both structural and chemical similarities with the nanolaminated MAX phases (Mn+1AXn (n = 1–3) where M usually is an early transition metal, A is typically an element in group 13–14 and X is C or N), and can be described as CrB slabs separated by layers of Al. Combinatorial sputtering was used to optimise the sputtering process parameters for films with the Cr2AlB2 composition. The influences of substrate, temperature and composition were studied using X-ray diffraction, X-ray photoelectron spectroscopy and electron microscopy. Films deposited at room temperature were X-ray amorphous but crystalline films could be deposited on MgO substrates at 680 °C using a composite Al-B, Cr and Al targets. X-ray diffraction analyses showed that the phase composition and texture of the films was strongly dependent on the chemical composition. Films with several phases or with a single Cr2AlB2 phase could be deposited, but an additional Al target was required to compensate for a loss of Al at the high deposition temperatures used in this study. The microstructure evolution during film growth was strongly dependent on composition, with a change in texture in Al-rich films from a preferred [010] orientation to a [100]/[001] orientation. A model based on Al desorption from the surface of the growing grains is proposed to explain the texture variations.
Open AccessMagnetron Sputtering of Nanolaminated Cr2AlB2
A ternary Cr2AlB2 phase was deposited as a film using magnetron sputtering. Its anisotropic structure displays both structural and chemical similarities with the nanolaminated MAX phases (Mn+1AXn (n = 1–3) where M usually is an early transition metal, A is typically an element in group 13–14 and X is C or N), and can be described as CrB slabs separated by layers of Al. Combinatorial sputtering was used to optimise the sputtering process parameters for films with the Cr2AlB2 composition. The influences of substrate, temperature and composition were studied using X-ray diffraction, X-ray photoelectron spectroscopy and electron microscopy. Films deposited at room temperature were X-ray amorphous but crystalline films could be deposited on MgO substrates at 680 °C using a composite Al-B, Cr and Al targets. X-ray diffraction analyses showed that the phase composition and texture of the films was strongly dependent on the chemical composition. Films with several phases or with a single Cr2AlB2 phase could be deposited, but an additional Al target was required to compensate for a loss of Al at the high deposition temperatures used in this study. The microstructure evolution during film growth was strongly dependent on composition, with a change in texture in Al-rich films from a preferred [010] orientation to a [100]/[001] orientation. A model based on Al desorption from the surface of the growing grains is proposed to explain the texture variations.
- Open Access
Influence of Deposition Temperature on the Phase Evolution of HfNbTiVZr High-Entropy Thin Films
In this study, we show that the phase formation of HfNbTiVZr high-entropy thin films is strongly influenced by the substrate temperature. Films deposited at room temperature exhibit an amorphous microstructure and are 6.5 GPa hard. With increasing substrate temperature (room temperature to 275 °C), a transition from an amorphous to a single-phased body-centred cubic (bcc) solid solution occurs, resulting in a hardness increase to 7.9 GPa. A higher deposition temperature (450 °C) leads to the formation of C14 or C15 Laves phase precipitates in the bcc matrix and a further enhancement of mechanical properties with a peak hardness value of 9.2 GPa. These results also show that thin films follow different phase formation pathways compared to HfNbTiVZr bulk alloys.
Open AccessInfluence of Deposition Temperature on the Phase Evolution of HfNbTiVZr High-Entropy Thin Films
In this study, we show that the phase formation of HfNbTiVZr high-entropy thin films is strongly influenced by the substrate temperature. Films deposited at room temperature exhibit an amorphous microstructure and are 6.5 GPa hard. With increasing substrate temperature (room temperature to 275 °C), a transition from an amorphous to a single-phased body-centred cubic (bcc) solid solution occurs, resulting in a hardness increase to 7.9 GPa. A higher deposition temperature (450 °C) leads to the formation of C14 or C15 Laves phase precipitates in the bcc matrix and a further enhancement of mechanical properties with a peak hardness value of 9.2 GPa. These results also show that thin films follow different phase formation pathways compared to HfNbTiVZr bulk alloys.
- Open Access
- 31 October 2016
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 8 (44) , 30635-30643
Combinatorial Study of Gradient Ag–Al Thin Films: Microstructure, Phase Formation, Mechanical and Electrical Properties
A combinatorial approach is applied to rapidly deposit and screen Ag–Al thin films to evaluate the mechanical, tribological, and electrical properties as a function of chemical composition. Ag–Al thin films with large continuous composition gradients (6–60 atom % Al) were deposited by a custom-designed combinatorial magnetron sputtering system. X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), scanning and transmission electron microscopy (SEM and TEM), X-ray photoelectron spectroscopy (XPS), nanoindentation, and four-point electrical resistance screening were employed to characterize the chemical composition, structure, and physical properties of the films in a time-efficient way. For low Al contents (1) and adhesive wear, similar to the behavior of pure Ag. In contrast, the hexagonal solid solution phase (from ca. 15 atom %Al) exhibited dramatically reduced friction coefficients (about 15% of that of the fcc phase) and dramatically reduced adhesive wear when tested against the pure Ag counter surface. The increase in contact resistance of the Ag–Al films is limited to only 50% higher than a pure Ag reference sample at the low friction and low wear region (19–27 atom %). This suggests that a hcp Ag–Al alloy can have a potential use in sliding electrical contact applications and in the future will replace pure Ag in specific electromechanical applications.
- 31 October 2016
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 8 (44) , 30635-30643
Open AccessCombinatorial Study of Gradient Ag–Al Thin Films: Microstructure, Phase Formation, Mechanical and Electrical Properties
A combinatorial approach is applied to rapidly deposit and screen Ag–Al thin films to evaluate the mechanical, tribological, and electrical properties as a function of chemical composition. Ag–Al thin films with large continuous composition gradients (6–60 atom % Al) were deposited by a custom-designed combinatorial magnetron sputtering system. X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), scanning and transmission electron microscopy (SEM and TEM), X-ray photoelectron spectroscopy (XPS), nanoindentation, and four-point electrical resistance screening were employed to characterize the chemical composition, structure, and physical properties of the films in a time-efficient way. For low Al contents (1) and adhesive wear, similar to the behavior of pure Ag. In contrast, the hexagonal solid solution phase (from ca. 15 atom %Al) exhibited dramatically reduced friction coefficients (about 15% of that of the fcc phase) and dramatically reduced adhesive wear when tested against the pure Ag counter surface. The increase in contact resistance of the Ag–Al films is limited to only 50% higher than a pure Ag reference sample at the low friction and low wear region (19–27 atom %). This suggests that a hcp Ag–Al alloy can have a potential use in sliding electrical contact applications and in the future will replace pure Ag in specific electromechanical applications.
- 4 November 1998
- Published by AIP Publishing in Applied Physics Letters
- Vol. 73 (19) , 2754-2756
Deposition of transition metal carbide superlattices using C60 as a carbon source
Epitaxial films of TiC and VC can be deposited at low temperatures on Mg(001) substrates by coevaporation of the metals with in a ultrahigh vacuum system. This process was used to deposit TiC/VC (001) superlattices on MgO(001) at 400 °C. The superlattice structure was characterized with low electron energy diffraction, x-ray diffraction, and transmission electron microscopy (TEM). Cross-sectional high-resolution TEM showed good registry between the different carbide layers.- 4 November 1998
- Published by AIP Publishing in Applied Physics Letters
- Vol. 73 (19) , 2754-2756
Deposition of transition metal carbide superlattices using C60 as a carbon source
Epitaxial films of TiC and VC can be deposited at low temperatures on Mg(001) substrates by coevaporation of the metals with in a ultrahigh vacuum system. This process was used to deposit TiC/VC (001) superlattices on MgO(001) at 400 °C. The superlattice structure was characterized with low electron energy diffraction, x-ray diffraction, and transmission electron microscopy (TEM). Cross-sectional high-resolution TEM showed good registry between the different carbide layers.