Wilfried Vandervorst
Wilfried Vandervorst has a total of 123 co-authors. Here are the top co-authors by number of shared publications:
Trudo Clarysse
IMEC, Leuven, Belgium
10 shared publicationsRong Lin
CAPRES A/S , Scion-DTU, Building 373, DK-2800 Kgs. Lyngby, Denmark
6 shared publications- Alain Moussa
IMEC, 3001 Leuven, Belgium
5 shared publications - Pierre Eyben
Imec, Kapeldreef 75, 3001 Leuven, Belgium
5 shared publications Janusz Bogdanowicz
KU Leuven Instituut voor Kern-en Stralingsfysika Celestijnenlaan 200D B-3001 Leuven, Belgium and , Kapeldreef 75, B-3001 Leuven, Belgium
4 shared publicationsAlex Salnik
KLA-Tencor Corp. , One Technology Drive, Milpitas, California 95035
3 shared publications
Latest Publications
- Open Access
Epitaxial Defects in Nanoscale InP Fin Structures Revealed by Wet-Chemical Etching
In this work, we report on wet-chemical defect revealing in InP fin structures relevant for device manufacturing. Both HCl and HBr solutions were explored using bulk InP as a reference. A distinct difference in pit morphology was observed between the two acids, attributed to an anisotropy in step edge reactivity. The morphology of the etch pits in bulk InP suggests that the dislocations are oriented mainly perpendicular to the surface. By studying the influence of the acid concentration on the InP fin recess in nanoscale trenches, it was found that aqueous HCl solution was most suitable for revealing defects. Planar defects in InP fin structures grown by the aspect ratio trapping technique could be visualized as characteristic shallow grooves approximately one nanometer deep. It is challenging to reveal defects in wide-field InP fins. In these structures, dislocations also reach the surface next to stack faults or twinning planes. Due to the inclined nature, dislocation-related pits are only a few atomic layers deep. Extending the pits is limited by the high reactivity of the fin sides and the strong surface roughening during etching. The process window for revealing wet-chemical defects in InP fins is limited.
Open AccessEpitaxial Defects in Nanoscale InP Fin Structures Revealed by Wet-Chemical Etching
In this work, we report on wet-chemical defect revealing in InP fin structures relevant for device manufacturing. Both HCl and HBr solutions were explored using bulk InP as a reference. A distinct difference in pit morphology was observed between the two acids, attributed to an anisotropy in step edge reactivity. The morphology of the etch pits in bulk InP suggests that the dislocations are oriented mainly perpendicular to the surface. By studying the influence of the acid concentration on the InP fin recess in nanoscale trenches, it was found that aqueous HCl solution was most suitable for revealing defects. Planar defects in InP fin structures grown by the aspect ratio trapping technique could be visualized as characteristic shallow grooves approximately one nanometer deep. It is challenging to reveal defects in wide-field InP fins. In these structures, dislocations also reach the surface next to stack faults or twinning planes. Due to the inclined nature, dislocation-related pits are only a few atomic layers deep. Extending the pits is limited by the high reactivity of the fin sides and the strong surface roughening during etching. The process window for revealing wet-chemical defects in InP fins is limited.
- 10 May 2016
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 5 (7) , P396-P403
Quasi Two-Dimensional Si-O Superlattices: Atomically Controlled Growth and Electrical Properties
We perform a systematic study on the growth of epitaxial Silicon–Oxygen superlattices (SLs) and investigate the impact of structural properties on the electrical performance. Si layers and O atomic layers (ALs) are deposited using SiH4 and O3 reactions respectively. Although the deposition of O ALs and epitaxial Si thereon, i.e. 1st period of Si–O SL is well documented, the controlled deposition in maintaining the overall crystalline quality of SL is still a challenge. This is due to inability to limit the O layer to sub-AL content (1AL = 6.7 × 1014 at/cm2) at higher periods (≥2). The Si surface prior to O AL deposition is chemically modified with H-passivation and sub-AL O-content is achieved. This ensures minimum structural distortions, enabling epitaxial ordering of Si and hence the epitaxial Si–O SL up to 5-periods. No SiOx clusters are detected and O layers are stable at Si deposition temperature. Electrically, donor defects increase with Si–O periods and partially reduced with forming gas anneal. The presence of defects and increased roughness during the growth, degrade the mobility due to coulomb and surface scattering respectively. It can be circumvented by optimizing SL parameters and other process integration parameters subjected for future research.
- 10 May 2016
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 5 (7) , P396-P403
Quasi Two-Dimensional Si-O Superlattices: Atomically Controlled Growth and Electrical Properties
We perform a systematic study on the growth of epitaxial Silicon–Oxygen superlattices (SLs) and investigate the impact of structural properties on the electrical performance. Si layers and O atomic layers (ALs) are deposited using SiH4 and O3 reactions respectively. Although the deposition of O ALs and epitaxial Si thereon, i.e. 1st period of Si–O SL is well documented, the controlled deposition in maintaining the overall crystalline quality of SL is still a challenge. This is due to inability to limit the O layer to sub-AL content (1AL = 6.7 × 1014 at/cm2) at higher periods (≥2). The Si surface prior to O AL deposition is chemically modified with H-passivation and sub-AL O-content is achieved. This ensures minimum structural distortions, enabling epitaxial ordering of Si and hence the epitaxial Si–O SL up to 5-periods. No SiOx clusters are detected and O layers are stable at Si deposition temperature. Electrically, donor defects increase with Si–O periods and partially reduced with forming gas anneal. The presence of defects and increased roughness during the growth, degrade the mobility due to coulomb and surface scattering respectively. It can be circumvented by optimizing SL parameters and other process integration parameters subjected for future research.
- 22 July 2015
- Published by Wiley in Physica Status Solidi (a)
- Vol. 212 (11) , 2595-2599
Suppression of boron incorporation at the early growth phases of boron‐doped diamond thin films
- 22 July 2015
- Published by Wiley in Physica Status Solidi (a)
- Vol. 212 (11) , 2595-2599
Suppression of boron incorporation at the early growth phases of boron‐doped diamond thin films
- 17 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 61 (8) , 2633-2639
Accurate Prediction of Device Performance Based on 2-D Carrier Profiles in the Presence of Extensive Mobile Carrier Diffusion
In this paper, we illustrate how high-resolution 2-D carrier profiles from scanning spreading resistance microscopy (SSRM) can be used to predict and understand device performance of dynamic random access memory peripheral transistors with high-k metal gate and ultrashallow junctions. In an earlier study on high-speed complementary metal-oxide-semiconductor logic, the 2-D carrier profiles from SSRM were used as the active 2-D dopant profile input to the device simulator as they are virtually identical. The extensive mobile carrier diffusion caused by the lower concentrations, however, implies a strong difference between the mobile carrier distribution and the dopant distribution such that the same approach is no longer valid. Ideally one would have to generate, based on the carrier profiles, the active dopant distribution through the inverse solution of the Poisson equation (in two dimensions) which is, however, numerically nontrivial and often leads to nonunique results. Therefore, an alternative approach is proposed here, whereby we fine-tune the process simulations such that the resulting simulated carrier profiles match the 2-D SSRM profiles. Upon reaching satisfactory agreement, the simulated profiles can be used as input for a device simulator and be used to predict sensitive device parameters such as drain-induced barrier lowering and threshold voltage rolloff.
- 17 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 61 (8) , 2633-2639
Accurate Prediction of Device Performance Based on 2-D Carrier Profiles in the Presence of Extensive Mobile Carrier Diffusion
In this paper, we illustrate how high-resolution 2-D carrier profiles from scanning spreading resistance microscopy (SSRM) can be used to predict and understand device performance of dynamic random access memory peripheral transistors with high-k metal gate and ultrashallow junctions. In an earlier study on high-speed complementary metal-oxide-semiconductor logic, the 2-D carrier profiles from SSRM were used as the active 2-D dopant profile input to the device simulator as they are virtually identical. The extensive mobile carrier diffusion caused by the lower concentrations, however, implies a strong difference between the mobile carrier distribution and the dopant distribution such that the same approach is no longer valid. Ideally one would have to generate, based on the carrier profiles, the active dopant distribution through the inverse solution of the Poisson equation (in two dimensions) which is, however, numerically nontrivial and often leads to nonunique results. Therefore, an alternative approach is proposed here, whereby we fine-tune the process simulations such that the resulting simulated carrier profiles match the 2-D SSRM profiles. Upon reaching satisfactory agreement, the simulated profiles can be used as input for a device simulator and be used to predict sensitive device parameters such as drain-induced barrier lowering and threshold voltage rolloff.
- 1 May 2013
- Published by Elsevier in Diamond and Related Materials
- Vol. 35, 14-18
Diamond nano-particle seeding for tip moulding application
- 1 May 2013
- Published by Elsevier in Diamond and Related Materials
- Vol. 35, 14-18
Diamond nano-particle seeding for tip moulding application
- 8 June 2012
- Published by Elsevier in Applied Surface Science
- Vol. 258 (24) , 9579-9583
Si nanoripples: A growth dynamical study
- 8 June 2012
- Published by Elsevier in Applied Surface Science
- Vol. 258 (24) , 9579-9583
Si nanoripples: A growth dynamical study
- 1 January 2010
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 28 (1) , C1C8-C1C14
Photovoltage versus microprobe sheet resistance measurements on ultrashallow structures
Earlier work [T. Clarysse , Mater. Sci. Eng., B 114-115, 166 (2004); T. Clarysse , Mater. Res. Soc. Symp. Proc. 912, 197 (2006)] has shown that only few contemporary tools are able to measure reliably (within the international technology roadmap for semiconductors specifications) sheet resistances on ultrashallow (sub-50-nm) chemical-vapor-deposited layers [T. Clarysse , Mater. Res. Soc. Symp. Proc. 912, 197 (2006)], especially in the presence of medium/highly doped underlying layers (representative for well/halo implants). Here the authors examine more closely the sheet resistance anomalies which have recently been observed between junction photovoltage (JPV) based tools and a micrometer-resolution four-point probe (M4PP) tool on a variety of difficult, state-of-the-art sub-32-nm complementary metal-oxide semiconductor structures (low energy and cluster implants, with/without halo, flash- and laser-based millisecond anneal). Conventional four-point probe tools fail on almost all of these samples due to excessive probe penetration, whereas in several cases variable probe spacing (using a conventional spreading resistance probe tool) [T. Clarysse , Mater. Sci. Eng. R. 47, 123 (2004)] still gives useful values to within about 20%-35% due to its limited probe penetration (5-10 nm at 5 g load). M4PP measurements give systematically a sensible and reproducible result. This is also the case for JPV-based sheet resistance measurements, although these appear to be prone to correct calibration procedures and are not designed for the characterization of multijunctions. Moreover, in a significant number of cases, residual damage and/or unexpected junction-leakage currents appear to induce a strong signal reduction, limiting the applicability of the JPV technique. This has been further investigated by transmission-electron microscopy, high carrier-injection photomodulated optical-reflectance, and Synopsis-Sentaurus device simulations
- 1 January 2010
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 28 (1) , C1C8-C1C14
Photovoltage versus microprobe sheet resistance measurements on ultrashallow structures
Earlier work [T. Clarysse , Mater. Sci. Eng., B 114-115, 166 (2004); T. Clarysse , Mater. Res. Soc. Symp. Proc. 912, 197 (2006)] has shown that only few contemporary tools are able to measure reliably (within the international technology roadmap for semiconductors specifications) sheet resistances on ultrashallow (sub-50-nm) chemical-vapor-deposited layers [T. Clarysse , Mater. Res. Soc. Symp. Proc. 912, 197 (2006)], especially in the presence of medium/highly doped underlying layers (representative for well/halo implants). Here the authors examine more closely the sheet resistance anomalies which have recently been observed between junction photovoltage (JPV) based tools and a micrometer-resolution four-point probe (M4PP) tool on a variety of difficult, state-of-the-art sub-32-nm complementary metal-oxide semiconductor structures (low energy and cluster implants, with/without halo, flash- and laser-based millisecond anneal). Conventional four-point probe tools fail on almost all of these samples due to excessive probe penetration, whereas in several cases variable probe spacing (using a conventional spreading resistance probe tool) [T. Clarysse , Mater. Sci. Eng. R. 47, 123 (2004)] still gives useful values to within about 20%-35% due to its limited probe penetration (5-10 nm at 5 g load). M4PP measurements give systematically a sensible and reproducible result. This is also the case for JPV-based sheet resistance measurements, although these appear to be prone to correct calibration procedures and are not designed for the characterization of multijunctions. Moreover, in a significant number of cases, residual damage and/or unexpected junction-leakage currents appear to induce a strong signal reduction, limiting the applicability of the JPV technique. This has been further investigated by transmission-electron microscopy, high carrier-injection photomodulated optical-reflectance, and Synopsis-Sentaurus device simulations
- 1 January 2010
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 28 (1) , C1C1-C1C7
Nondestructive extraction of junction depths of active doping profiles from photomodulated optical reflectance offset curves
- 1 January 2010
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 28 (1) , C1C1-C1C7
Nondestructive extraction of junction depths of active doping profiles from photomodulated optical reflectance offset curves
- 1 January 2010
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 28 (1) , C1C21-C1C26
Study of submelt laser induced junction nonuniformities using Therma-Probe
Submelt laser annealing is a promising technique to achieve the required sheet resistance and junction depth specifications for the 32 nm technology node and beyond. In order to obtain a production worthy process, it is important to minimize possible nonuniformities caused by the annealing process both at macroscopic and microscopic levels. In this work, the authors present high resolution Therma-Probe® measurements to assess the junction nonuniformity on 0.5 keV boron junctions and zoom in on the effect of temperature variations and multiple subsequent laser scans. The results are compared to standard and micro-four-point probe sheet resistance data, secondary ion mass spectrometry, and Hall measurements obtained during earlier studies. Besides the impact of the nonuniformities on the “conventional” thermal wave signal, they found a strong correlation to the dc reflectance of the probe laser (λ = 675 nm). The dc probe reflectance is dominated by free carriers and is highly correlated to the sheet resistance both on blanket wafers and on real device wafers.
- 1 January 2010
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 28 (1) , C1C21-C1C26
Study of submelt laser induced junction nonuniformities using Therma-Probe
Submelt laser annealing is a promising technique to achieve the required sheet resistance and junction depth specifications for the 32 nm technology node and beyond. In order to obtain a production worthy process, it is important to minimize possible nonuniformities caused by the annealing process both at macroscopic and microscopic levels. In this work, the authors present high resolution Therma-Probe® measurements to assess the junction nonuniformity on 0.5 keV boron junctions and zoom in on the effect of temperature variations and multiple subsequent laser scans. The results are compared to standard and micro-four-point probe sheet resistance data, secondary ion mass spectrometry, and Hall measurements obtained during earlier studies. Besides the impact of the nonuniformities on the “conventional” thermal wave signal, they found a strong correlation to the dc reflectance of the probe laser (λ = 675 nm). The dc probe reflectance is dominated by free carriers and is highly correlated to the sheet resistance both on blanket wafers and on real device wafers.