KKKarsten Kusterer

Karsten Kusterer

*This is an algorithmically generated author record based on publicly available information.

Karsten Kusterer has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Numerical and Analytical Investigation of Heat Transfer Mechanisms and Flow Phenomena in an IP Steam Turbine Blading During Startup

    by Dieter Bohn, Christian Betcher, Karsten Kusterer, Kristof Weidtmann

    As a result of an ever-increasing share of volatile renewable energies on the world wide power generation, conventional thermal power plants face high technical challenges in terms of operational flexibility. Consequently, the number of startups and shutdowns grows, causing high thermal stresses in the thick-walled components and thus reduces lifetime and increases product

  • Numerical and Analytical Investigation of Heat Transfer Mechanisms and Flow Phenomena in an Intermediate Pressure Steam Turbine Blading During Startup

    by Dieter Bohn, Christian Betcher, Karsten Kusterer, Kristof Weidtmann

    As a result of an ever-increasing share of volatile renewable energies on the worldwide power generation, conventional thermal power plants face high technical challenges in terms of operational flexibility. Consequently, the number of startups and shutdowns grows, causing high thermal stresses in the thick-walled components and thus reduces lifetime and increases product costs. To fulfill the lifetime requirements, an accurate prediction and determination of the metal temperature distribution inside these components is crucial. Therefore, boundary conditions in terms of local fluid temperatures as well as heat transfer coefficients (HTCs) with sufficient accuracy are required. As modern numerical modeling approaches, like 3D-conjugate-heat-transfer (CHT), provide these thermal conditions with a huge calculation expense for multistage turbines, simplified methods are inevitable. Analytical heat transfer correlations are thus the state-of-the-art approach to capture the heat transport phenomena and to optimize and design high efficient startup curves for flexible power market. The objective of this paper is to understand the predominant basic heat transfer mechanisms such as conduction, convection, and radiation during a startup of an intermediate pressure (IP) steam turbine stage. Convective heat transport is described by means of heat transfer coefficients as a function of the most relevant dimensionless, aero-thermal operating parameters, considering predominant flow structures. Based on steady-state and transient CHT simulations, the heat transfer coefficients are derived during startup procedure and compared to analytical correlations from the literature, which allow the calculation of the heat exchange for a whole multistage in an economic and timesaving way. The simulations point out that the local convective heat transfer coefficient generally increases with increasing axial and circumferential Reynolds' number and is mostly influenced by vortex systems such as passage and horseshoe vortices. The heat transfer coefficients at vane, blade, hub, and labyrinth-sealing surfaces can be modeled with a high accuracy using a linear relation with respect to the total Reynolds' number. The comparison illustrates that the analytical correlations underestimate the convective heat transfer by approximately 40% on average. Results show that special correlation-based approaches from the literature are a particularly suitable and efficient procedure to predict the heat transfer within steam turbines in the thermal design process. Overall, the computational effort can be significantly reduced by applying analytical correlations while maintaining a satisfactory accuracy.


  • Experimental and Numerical Study on Optimizing the Dry Low NOx Micromix Hydrogen Combustion Principle for Industrial Gas Turbine Applications

    by Harald H. W. Funke, Jan Keinz, Karsten Kusterer, Anis Haj Ayed, Masahide Kazari, Junichi Kitajima, Atsushi Horikawa, Kunio Okada

    Combined with the use of renewable energy sources for its production, hydrogen represents a possible alternative gas turbine fuel for future low-emission power generation. Due to the difference in the physical properties of hydrogen compared to other fuels such as natural gas, well-established gas turbine combustion systems cannot be directly applied to dry low NOx (DLN) hydrogen combustion. The DLN micromix combustion of hydrogen has been under development for many years, since it has the promise to significantly reduce NOx emissions. This combustion principle for air-breathing engines is based on crossflow mixing of air and gaseous hydrogen. Air and hydrogen react in multiple miniaturized diffusion-type flames with an inherent safety against flashback and with low NOx emissions due to a very short residence time of the reactants in the flame region. The paper presents an advanced DLN micromix hydrogen application. The experimental and numerical study shows a combustor configuration with a significantly reduced number of enlarged fuel injectors with high-thermal power output at constant energy density. Larger fuel injectors reduce manufacturing costs, are more robust and less sensitive to fuel contamination and blockage in industrial environments. The experimental and numerical results confirm the successful application of high-energy injectors, while the DLN micromix characteristics of the design point, under part-load conditions, and under off-design operation are maintained. Atmospheric test rig data on NOx emissions, optical flame-structure, and combustor material temperatures are compared to numerical simulations and show good agreement. The impact of the applied scaling and design laws on the miniaturized micromix flamelets is particularly investigated numerically for the resulting flow field, the flame-structure, and NOx formation.


  • Numerical and Experimental Investigations of the Transient Thermal Behavior of a Steam By-Pass Valve at Steam Temperatures Beyond 700 °C

    by Anis Haj Ayed, Martin Kemper, Karsten Kusterer, Hailu Tadesse, Manfred Wirsum, Dierk von Nordheim, Olaf Tebbenhoff, Karl-Heinz Czychon, Klaus Metzger, Dieter Bohn

    Increasing the efficiency of steam power plants is important to reduce their CO2 emissions and can be achieved by increasing steam temperatures beyond 700 °C. Within the present study, the thermal behavior of a steam by-pass valve subject to cyclic operation with 700 °C steam is investigated experimentally and numerically. An innovative numerical approach was applied to predict the valve’s thermal behavior during cyclic operation, which is essential for fatigue life assessment of such a component. Validation of the applied numerical approach has shown good agreement with measurement results, indicating the potential of its application for the valve design process.


  • Film Cooling Effectiveness Comparison Between Shaped- and Double Jet Film Cooling Holes in a Row Arrangement

    by Karsten Kusterer, Anas Elyas, Dieter Bohn, Takao Sugimoto, Ryozo Tanaka, Masahide Kazari

    The improvement of the thermal efficiency of modern gas turbines can be achieved by reducing the needed cooling air amount. Consequently it is required to increase the cooling efficiency of applied cooling technologies. Streamwise ejection from a cylindrical hole causes kidney vortices which transport hot gas underneath the cooling jet and leads the cooling jet to lift off from the surface. Cooling performance is highly increased by using the shaped hole technique, which weakens the kidney vortex structure. However the formation of secondary flows can not completely be avoided by using shaped holes instead of cylindrical holes. Another promising film cooling technology is the double-jet film cooling, which prevents the cooling jet from lifting off the surface and raises the lateral spreading of the cooling air by generating an anti kidney vortex. This paper presents a comparison of the film cooling effectiveness between the shaped film cooling technique and the novel double jet film cooling technique for the high blowing ratios M = 1, M = 1.5 and M = 2. Various geometries of fan-shaped holes with lateral expansion angles of 10°, 14° and 18° are used for the comparison study. It can be shown that the shaped hole row arrangement provides higher cooling values in a slight region near to the hole exits, while the double jet film cooling technique shows a obvious cooling advantage in the further downstream area for high blowing ratios. Furthermore recent results of an on-going experimental comparison study between the double jet, trench and cylindrical technique are presented, which proves the advantage capability of the double jet film cooling.


  • Double-Jet Ejection of Cooling Air for Improved Film Cooling

    by Karsten Kusterer, Dieter Bohn, Takao Sugimoto, Ryozo Tanaka

    Film cooling in gas turbines leads to aerodynamic mixing losses and reduced temperatures of the gas flow. Improvements of the gas turbine thermal efficiency can be achieved by reducing the cooling fluid amount and by establishing a more equal distribution of the cooling fluid along the surface. It is well known that vortex systems in the cooling jets are the origin of reduced film-cooling effectiveness. For the streamwise ejection case, kidney vortices result in a liftoff of the cooling jets; for the lateral ejection case, usually only one dominating vortex remains, leading to hot gas flow underneath the jet from one side. Based on the results of numerical analyses, a new cooling technology has been introduced by the authors, which reaches high film-cooling effectiveness as a result of a well-designed cooling hole arrangement for interaction of two neighboring cooling jets (double-jet film cooling (DJFC)). The results show that configurations exist, where an improved film-cooling effectiveness can be reached because an anti-kidney vortex pair is established in the double-jet. The paper aims at the following major contributions: (1) to introduce the DJFC as an alternative film-cooling technology to conventional film-cooling design; (2) to explain the major phenomena, which leads to the improvement of the film-cooling effectiveness by application of the DJFC; and (3) to prove basic applicability of the DJFC to a realistic blade cooling configuration and present the first test results under machine operating conditions.


  • Double-Jet Ejection of Cooling Air for Improved Film-Cooling

    by Karsten Kusterer, Dieter Bohn, Takao Sugimoto, Ryozo Tanaka

    Film-cooling in gas turbines leads to aerodynamic mixing losses and reduced temperatures of the gas flow. Improvements of the gas turbine thermal efficiency can be achieved by reducing the cooling fluid amount and by establishing a more equal distribution of the cooling fluid along the surface. It is well known that vortex systems in the cooling jets are the origin of reduced film-cooling effectiveness. For the streamwise ejection case, kidney-vortices result in a lift-off of the cooling jets; for the lateral ejection case, usually only one dominating vortex remains, leading to hot gas flow underneath the jet from one side. Based on the results of numerical analyses, a new cooling technology has been introduced by the authors, which reaches high film-cooling effectiveness as a result of a well-designed cooling hole arrangement for interaction of two neighbouring cooling jets (Double-jet Film-cooling DJFC). The results show that configurations exist, where an improved film-cooling effectiveness can be reached because an anti-kidney vortex pair is established in the double-jet. The paper aims on following major contributions: • to introduce the Double-jet Film-cooling (DJFC) as an alternative film-cooling technology to conventional film-cooling design. • to explain the major phenomena, which lead to the improvement of the film-cooling effectiveness by application of the DJFC. • to prove basic applicability of the DJFC to a realistic blade cooling configuration and present first test results under machine operating conditions.


  • Conjugate Flow and Heat Transfer Investigation of a Turbo Charger

    by Dieter Bohn, Tom Heuer, Karsten Kusterer

    In this paper a three-dimensional conjugate calculation has been performed for a passenger car turbo charger. The scope of this work is to investigate the heat fluxes in the radial compressor, which can be strongly influenced by the hot turbine. As a result of this, the compressor efficiency may deteriorate. Consequently, the heat fluxes have to be taken into account for the determination of the efficiency. To overcome this problem a complex three-dimensional model has been developed. It contains the compressor, the oil cooled center housing, and the turbine. Twelve operating points have been numerically simulated composed of three different turbine inlet temperatures and four different mass flows. The boundary conditions for the flow and for the outer casing were derived from experimental test data (Bohn et al.). Resulting from these conjugate calculations various one-dimensional calculation specifications have been developed. They describe the heat transfer phenomena inside the compressor with the help of a Nusselt number, which is a function of an artificial Reynolds number and the turbine inlet temperature.


  • Conjugate Calculations for a Film-Cooled Blade Under Different Operating Conditions

    by Karsten Kusterer, Dieter Bohn, Takao Sugimoto, Ryozo Tanaka

    Conjugate heat transfer and flow calculation techniques (CCT: Conjugate Calculation Technique) developed by several numerical groups have been applied to more and more complex three-dimensional cooling configurations. With respect to gas turbine blade cooling, conjugate calculation codes are turning out as useful tools for the support of the thermal design process. Thus, the main focus of the present study is to investigate the applicability of the CCT on a realistic film-cooling configuration of a modern gas turbine blade under hot gas operating conditions. Thermal index paint measurements for the investigated configuration have been performed at KHI Gas Turbine R&D Center in order to provide thermal load data for comparison to results of conjugate blade analysis. The comparison shows that with respect to regions with high thermal load a qualitatively good agreement of the conjugate results and the measurements can be found although the calculation models contain several simplifications for the internal cooling configuration particularly. The tip region of the blade trailing edge is exposed to a high thermal load. This result can be found in the measurement data as well as in the numerical analysis. The influence of off-design flow conditions on the film cooling flow at the blade leading edge is also investigated. Despite the model simplification, the Conjugate Calculation Technique turns out to be applicable for the numerical testing of the cooling configuration investigated. With the numerical results, useful information for further improvement of the investigated cooling configuration can be provided.


  • Open Access

    C103 CONJUGATE HEAT TRANSFER, INTERNAL FLOW, AND EXTERNAL FLOW ANALYSES FOR A FILM-COOLED BLADE

    by Kusterer Karsten, Dieter Bohn, Takao Sugimoto, Ryozo Tanaka

    The conjugate calculation technique is used for the three-dimensional heat transfer, internal flow, and external flow calculation of a film-cooled test blade of a modern gas turbine. The comparison with thermal index paint experiments shows that with respect to the thermal load a qualitatively good agreement of the conjugate results and the measurements can be found. The 3-D analysis permits to take into account the influence of off-design flow conditions, which lead to a shifting of the stagnation line, on the film cooling at the leading edge. The numerical simulation of the complex internal passage flow is also part of the investigation. It can be shown that a homogeneous distribution of the cooling air on the cooling holes is reached. Nevertheless, the interaction of the cooling jets with secondary flow phenomena of the passage flow can lead to cooling fluid displacement and, thus, to a local degradation of the cooling performance.