M. E. Aalami Aaleagha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
M. E. Aalami Aaleagha has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Ali Rashidi
Department of Neurosurgery, Otto-von-Guericke-University Magdeburg, 39120 Magdeburg, Germany
1 shared publication Behzad Hadi
1 shared publication- Ehsan Borzabadi Farahani
Department of Wind Energy, Technical University of Denmark, Frederiksborgvej 399, 4000 Roskilde, Denmark
1 shared publication M. Foroutan
Razi Univ, Fac Engn, Dept Mech Engn, Kermanshah 67149, Iran
1 shared publication- Mehrdad Foroutan
Department of Mechanical Engineering, Razi University, Kermanshah, Iran
1 shared publication Mohammad Ali Shahbazi
Razi University
1 shared publication
Latest Publications
- 19 August 2016
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 30 (8) , 3767-3776
3-dimensional numerical analysis of friction stir welding of copper and aluminum
- 19 August 2016
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 30 (8) , 3767-3776
3-dimensional numerical analysis of friction stir welding of copper and aluminum
- 1 February 2014
- Published by Elsevier in International Journal of Pressure Vessels and Piping
- Vol. 114-115, 69-75
Analysis preheat effect on thermal cycle and residual stress in a welded connection by FE simulation
- 1 February 2014
- Published by Elsevier in International Journal of Pressure Vessels and Piping
- Vol. 114-115, 69-75
Analysis preheat effect on thermal cycle and residual stress in a welded connection by FE simulation
- 28 January 2012
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 26 (1) , 181-185
Correlated macrostructural parameters of weld and weld current in the SMAW of small pipes
- 28 January 2012
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 26 (1) , 181-185
Correlated macrostructural parameters of weld and weld current in the SMAW of small pipes
- 7 December 2011
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 134 (1) , 011209
Finite Element Simulation of Welding Sequences Effect on Residual Stresses in Multipass Butt-Welded Stainless Steel Pipes
In this paper, a finite element simulation, based on abaqus software is presented for analyzing the temperature history and the residual stress states in multipass welds in stainless steel pipe. The uncoupled thermal–mechanical a three-dimensional (3D) model and a two-dimensional (2D) model are developed. The volumetric heat source with double ellipsoidal distribution for front and rear heat source, proposed by Goldak and Akhlaghi, has also been used. Furthermore, a moving heat source has been modeled by abaqus subroutine DFLUX. A user subroutine FILM has also been used to simulate the combined thermal boundary conditions. The results of both a 3D model and a 2D axisymmetric model which are compared with the available experimental measurements show good agreements. Predictions show that the axial and hoop residual stresses in a 3D model and a 2D axisymmetric model have the same distributions in all locations except the starting point of welding. The effects of welding sequences on the thermal and structural analysis are also investigated. Four types of welding sequences for circular welds of pipe have been used and thermal history and axial and hoop residual stresses are compared. Predictions show that for other locations (except the starting point of welding) there are no important differences of axial and hoop residual stresses for welding sequences and they have the same distribution along axial direction.
- 7 December 2011
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 134 (1) , 011209
Finite Element Simulation of Welding Sequences Effect on Residual Stresses in Multipass Butt-Welded Stainless Steel Pipes
In this paper, a finite element simulation, based on abaqus software is presented for analyzing the temperature history and the residual stress states in multipass welds in stainless steel pipe. The uncoupled thermal–mechanical a three-dimensional (3D) model and a two-dimensional (2D) model are developed. The volumetric heat source with double ellipsoidal distribution for front and rear heat source, proposed by Goldak and Akhlaghi, has also been used. Furthermore, a moving heat source has been modeled by abaqus subroutine DFLUX. A user subroutine FILM has also been used to simulate the combined thermal boundary conditions. The results of both a 3D model and a 2D axisymmetric model which are compared with the available experimental measurements show good agreements. Predictions show that the axial and hoop residual stresses in a 3D model and a 2D axisymmetric model have the same distributions in all locations except the starting point of welding. The effects of welding sequences on the thermal and structural analysis are also investigated. Four types of welding sequences for circular welds of pipe have been used and thermal history and axial and hoop residual stresses are compared. Predictions show that for other locations (except the starting point of welding) there are no important differences of axial and hoop residual stresses for welding sequences and they have the same distribution along axial direction.
- 9 June 2009
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 18 (4) , 519-524
A New Application of Thermal Spray in Preparation of Metallic Membrane for Concentration of Glucose Solution
- 9 June 2009
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 18 (4) , 519-524
A New Application of Thermal Spray in Preparation of Metallic Membrane for Concentration of Glucose Solution