Hee-Woo Rhee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hee-Woo Rhee has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Min-Kyu Song
Energy Lab, Samsung SDI Corporate R&D Center , Gyeonggi-do, South Korea
5 shared publicationsYoung-Taek Kim
Interdisciplinary Program of Integrated Biotechnology, Department of Chemical & Biomolecular Engineering , Sogang University , Seoul, South Korea
4 shared publicationsSung-Kyu Min
Interdisciplinary Program of Integrated Biotechnology, Department of Chemical & Biomolecular Engineering , Sogang University , Seoul, Korea
2 shared publications- Alevtina Smirnova
Univ. of Connecticut, Storrs, CT, 06259, United States
1 shared publication Bongjin Moon
Department of Chemistry , Sogang University , Seoul, Korea
1 shared publication- Byung Won Cho
Korea Institute of Science and Technology
1 shared publication
Latest Publications
- 1 March 2006
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 445 (1) , 193/[483]-200/[490]
Iron Corrosion Protection by Ultra-thin Conductive Films Based on Polypyrrole/Poly(methyl methacrylate) Composite
The metallic surfaces can be protected from the corrosive media by conducting polymer coating which provides passivation mechanism by redox chemistry. Their poor solubility and processibility were improved by the use of soluble polypyrrole (PPy) and composite with poly(methyl methacrylate) (PMMA). Soluble PPy was synthesized by controlling the monomer-to-oxidant ratio in the presence of dodecylbenzenesulfonic acid (DBSA) as a dopant. And then MMA was mixed with PPy/m-cresol solution to spin-coat onto iron. The 4-probe method was used to measure electrical conductivity and FTIR spectra were used to study the conjugation length of PPy. Scanning electron microscopic (SEM) images were obtained to observe the surface morphology. Tafel plots showed that the PMMA/PPy composite film caused a positive shift of around 200 mV in the corrosion potential and the anodic current decreased by two orders of magnitude compared with bare iron.
- 1 March 2006
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 445 (1) , 193/[483]-200/[490]
Iron Corrosion Protection by Ultra-thin Conductive Films Based on Polypyrrole/Poly(methyl methacrylate) Composite
The metallic surfaces can be protected from the corrosive media by conducting polymer coating which provides passivation mechanism by redox chemistry. Their poor solubility and processibility were improved by the use of soluble polypyrrole (PPy) and composite with poly(methyl methacrylate) (PMMA). Soluble PPy was synthesized by controlling the monomer-to-oxidant ratio in the presence of dodecylbenzenesulfonic acid (DBSA) as a dopant. And then MMA was mixed with PPy/m-cresol solution to spin-coat onto iron. The 4-probe method was used to measure electrical conductivity and FTIR spectra were used to study the conjugation length of PPy. Scanning electron microscopic (SEM) images were obtained to observe the surface morphology. Tafel plots showed that the PMMA/PPy composite film caused a positive shift of around 200 mV in the corrosion potential and the anodic current decreased by two orders of magnitude compared with bare iron.
- 1 March 2006
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 445 (1) , 167/[457]-175/[465]
Chemically Reactive Nanoparticle for Ultra-lowkApplications
The introduction of nanometer-sized pores into low dielectric (k) materials is the most promising approach in producing ultra-low dielectric constant materials (k < 2.2). However, since the increased pores in low-k films lowered the mechanical strengths, it is important to optimize the mechanical properties by controlling the pore morphologies such as pore size, its size distribution and interconnectivity. We prepared nanoporous low-k films by using a chemically reactive cyclodextrin (TESCD) as a porogen to acquire chemical bonding with the low-k matrix, poly(methyl trimethoxy silane-co-bistriethoxysilyl ethane). The porosity of nanoporous low-k films linearly increased with porogen loading, which indicated great compatibility between porogen and matrix, and its dielectric constant was as low as 2.2 (from 3.0) at 40% of porogen loading. Nanoindentor was applied on the nanoporous low-k films prepared by either TESCD or poly(caprolactone) porogen to measure elastic modulus and surface hardness. TESCD porogen resulted in much less reduction in elastic modulus and surface hardness from ∼ 16 GPa to ∼ 7.3 and from ∼ 2.7 GPa to ∼ 1.0 at 27% of porosity, respectively, while PCL porogen brought about the dramatic decrease in both mechanical properties at the corresponding porosity. This result may be due to the chemical bonding between TESCD and the matrix during its crosslinking reaction, which led pores.
- 1 March 2006
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 445 (1) , 167/[457]-175/[465]
Chemically Reactive Nanoparticle for Ultra-lowkApplications
The introduction of nanometer-sized pores into low dielectric (k) materials is the most promising approach in producing ultra-low dielectric constant materials (k < 2.2). However, since the increased pores in low-k films lowered the mechanical strengths, it is important to optimize the mechanical properties by controlling the pore morphologies such as pore size, its size distribution and interconnectivity. We prepared nanoporous low-k films by using a chemically reactive cyclodextrin (TESCD) as a porogen to acquire chemical bonding with the low-k matrix, poly(methyl trimethoxy silane-co-bistriethoxysilyl ethane). The porosity of nanoporous low-k films linearly increased with porogen loading, which indicated great compatibility between porogen and matrix, and its dielectric constant was as low as 2.2 (from 3.0) at 40% of porogen loading. Nanoindentor was applied on the nanoporous low-k films prepared by either TESCD or poly(caprolactone) porogen to measure elastic modulus and surface hardness. TESCD porogen resulted in much less reduction in elastic modulus and surface hardness from ∼ 16 GPa to ∼ 7.3 and from ∼ 2.7 GPa to ∼ 1.0 at 27% of porosity, respectively, while PCL porogen brought about the dramatic decrease in both mechanical properties at the corresponding porosity. This result may be due to the chemical bonding between TESCD and the matrix during its crosslinking reaction, which led pores.
- Open Access
- 1 January 2006
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 153 (12) , A2239-A2244
Ultrathin Reinforced Nanocomposite Membranes for Direct Methanol Fuel Cells
The organically treated montmorillonite (MMT) clays incorporated into the Nafion matrix by means of solution intercalation using dimethylacetamide (DMA) as a solvent have been tested. The diffraction patterns of the nanocomposite Nafion/MMT membranes indicated a disordered and exfoliated nanocomposite structure. The transmission electron microscopy images revealed that the clay layers are well nanodispersed in the Nafion matrix until the weight fraction of the MMT reaches 10wt%10wt% . The apparent improvement in thermal stability might result from the strong interaction between Nafion and MMT. The refractive index measurements indicated that the methanol permeability of the Nafion/MMT ultrathin membrane containing 1wt%1wt% MMT was 14 times lower in comparison to commercial Nafion 117 membranes. The direct methanol fuel cell (DMFC) with polytetrafluoroethylene-reinforced Nafion/MMT nanocomposite membrane (25μm)(25μm) at 400mA∕cm2400mA∕cm2 under dry air conditions and 60°C60°C cell temperature demonstrated 120mW∕cm2120mW∕cm2 power output, which was 50% higher in comparison to the DMFC with commercial Nafion 117 membrane.
- 1 January 2006
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 153 (12) , A2239-A2244
Open AccessUltrathin Reinforced Nanocomposite Membranes for Direct Methanol Fuel Cells
The organically treated montmorillonite (MMT) clays incorporated into the Nafion matrix by means of solution intercalation using dimethylacetamide (DMA) as a solvent have been tested. The diffraction patterns of the nanocomposite Nafion/MMT membranes indicated a disordered and exfoliated nanocomposite structure. The transmission electron microscopy images revealed that the clay layers are well nanodispersed in the Nafion matrix until the weight fraction of the MMT reaches 10wt%10wt% . The apparent improvement in thermal stability might result from the strong interaction between Nafion and MMT. The refractive index measurements indicated that the methanol permeability of the Nafion/MMT ultrathin membrane containing 1wt%1wt% MMT was 14 times lower in comparison to commercial Nafion 117 membranes. The direct methanol fuel cell (DMFC) with polytetrafluoroethylene-reinforced Nafion/MMT nanocomposite membrane (25μm)(25μm) at 400mA∕cm2400mA∕cm2 under dry air conditions and 60°C60°C cell temperature demonstrated 120mW∕cm2120mW∕cm2 power output, which was 50% higher in comparison to the DMFC with commercial Nafion 117 membrane.
- 17 August 2004
- Published by Elsevier in Electrochimica Acta
- Vol. 50 (2-3) , 645-648
Nafion/ZrSPP composite membrane for high temperature operation of PEMFCs
- 17 August 2004
- Published by Elsevier in Electrochimica Acta
- Vol. 50 (2-3) , 645-648
Nafion/ZrSPP composite membrane for high temperature operation of PEMFCs
- Open Access
- 1 January 2004
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 7 (6) , A127-A130
Incorporation of Zirconium Hydrogen Phosphate into Porous Ionomer Membranes
Nafion membrane was cast from 5 wt % Nafion/dimethly acetamide/2-propanol solution containing a hydrophobic plasticizer, and the phase-separated low molecular weight component was leached out from the Nafion matrix by solvent extraction using diethyl ether and methanol. The resultant porous Nafion membrane was doped in situ with zirconium hydrogen phosphate (ZHP) by zirconium chloride and phosphoric acid treatment. The maximum loading of ZHP nanoparticles increased to 40 wt % because of additional precipitation in the pore structure. Field-emission scanning electron micrographs showed that the pores were completely filled with in situ doped ZHP particles. Fourier transform infrared study confirmed that more ZHP fillers improved water retention and proton conductivity of the composite ionomer membrane at high-temperature regions above 100°C. As a result, the power density of Nafion/ZHP membranes was much higher than that of an as-received Nafion 115 membrane at elevated temperature. © 2004 The Electrochemical Society. All rights reserved.
- 1 January 2004
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 7 (6) , A127-A130
Open AccessIncorporation of Zirconium Hydrogen Phosphate into Porous Ionomer Membranes
Nafion membrane was cast from 5 wt % Nafion/dimethly acetamide/2-propanol solution containing a hydrophobic plasticizer, and the phase-separated low molecular weight component was leached out from the Nafion matrix by solvent extraction using diethyl ether and methanol. The resultant porous Nafion membrane was doped in situ with zirconium hydrogen phosphate (ZHP) by zirconium chloride and phosphoric acid treatment. The maximum loading of ZHP nanoparticles increased to 40 wt % because of additional precipitation in the pore structure. Field-emission scanning electron micrographs showed that the pores were completely filled with in situ doped ZHP particles. Fourier transform infrared study confirmed that more ZHP fillers improved water retention and proton conductivity of the composite ionomer membrane at high-temperature regions above 100°C. As a result, the power density of Nafion/ZHP membranes was much higher than that of an as-received Nafion 115 membrane at elevated temperature. © 2004 The Electrochemical Society. All rights reserved.
- 1 January 2002
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 377 (1) , 349-352
The Effect of Semi-IPN Structure on Gel-type Polymer Electrolyte
Thermal stability of PVdF Gel polymer electrolyte (GPE) was enhanced by crosslinking with PEGDA. The resulting semi-IPN structure reduced the crystallization of PVdF and had better affinity with organic liquid electrolyte. When the cell composed of LiCoO2/GPE/Li foil was tested at 80 °C, interfacial impedance results indicated the higher thermal stability of GPE than PVdF.
- 1 January 2002
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 377 (1) , 349-352
The Effect of Semi-IPN Structure on Gel-type Polymer Electrolyte
Thermal stability of PVdF Gel polymer electrolyte (GPE) was enhanced by crosslinking with PEGDA. The resulting semi-IPN structure reduced the crystallization of PVdF and had better affinity with organic liquid electrolyte. When the cell composed of LiCoO2/GPE/Li foil was tested at 80 °C, interfacial impedance results indicated the higher thermal stability of GPE than PVdF.
- 1 April 1996
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 280 (1) , 145-150
Anion Movement in Polypyrrole Films Prepared in Lithium Dodecylsulfate Aqueous Solutions
Electrochemical quartz crystal microbalance (EQCM) was used to study the redox reaction of polypyrrole (PPy) prepared in an aqueous solution containing anionic surfactant. EQCM result confirmed that the small cation in the electrolyte solution rapidly moved into/out of the PPy film during redox reaction at a potentiodynamic condition and also the bulky anion, dodecylsulfate ion (DS), additionally took part in redox reaction, especially in positive potential range above-0.2 V. The movement of anion was more clearly seen at potentiostatic condition than in voltammetric measurement, which implies the rate dependency of the anion movement in PPy film.
- 1 April 1996
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 280 (1) , 145-150
Anion Movement in Polypyrrole Films Prepared in Lithium Dodecylsulfate Aqueous Solutions
Electrochemical quartz crystal microbalance (EQCM) was used to study the redox reaction of polypyrrole (PPy) prepared in an aqueous solution containing anionic surfactant. EQCM result confirmed that the small cation in the electrolyte solution rapidly moved into/out of the PPy film during redox reaction at a potentiodynamic condition and also the bulky anion, dodecylsulfate ion (DS), additionally took part in redox reaction, especially in positive potential range above-0.2 V. The movement of anion was more clearly seen at potentiostatic condition than in voltammetric measurement, which implies the rate dependency of the anion movement in PPy film.