Lingjun Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lingjun Guo has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Hejun Li
2 shared publications- Hejun Li
School of Materials Science and Engineering, Northwestern Polytechnical University, Xi’an, China
2 shared publications Kezhi Li
2 shared publicationsDongsheng Zhang
Northwestern Polytechnical University
1 shared publication- Gang Kou
State Key Laboratory of Solidification Processing, Carbon/Carbon Composites Research Center, Northwestern Polytechnical University, Xi’an 710072, China
1 shared publication - Guohui Yuan
School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001, People's Republic of China
1 shared publication
Latest Publications
- Open Access
- 17 January 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (5) , 2889-2895
Enhancing the reversibility of the chemical evolution of the Ni-rich LiNi0.8Co0.1Mn0.1O2 cathode via a simple pre-oxidation process
H2O2 is adopted to treat the precursor of LiNi0.8Co0.1Mn0.1O2, which reduces the cation mixing of Li+/Ni2+ and residual lithium on the cathode.
- 17 January 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (5) , 2889-2895
Open AccessEnhancing the reversibility of the chemical evolution of the Ni-rich LiNi0.8Co0.1Mn0.1O2 cathode via a simple pre-oxidation process
H2O2 is adopted to treat the precursor of LiNi0.8Co0.1Mn0.1O2, which reduces the cation mixing of Li+/Ni2+ and residual lithium on the cathode.
- Open Access
Crack Evolution and Oxidation Failure Mechanism of a SiC-Ceramic Coating Reactively Sintered on Carbon/Carbon Composites
A SiC ceramic coating was prepared on carbon/carbon composites by pack cementation. The phase composition and microstructure of the coated specimens were characterized using X-ray diffraction instrument and scanning electron microscope. The results showed that the mass-loss percentage of the coated specimen was 9.5% after being oxidized for 20 h. The oxidation failure of the SiC ceramic coating at 1773 K was analysed by non-destructive X-ray computed tomography. The effective self-healing of cracks with widths below 12.7 μm introduced during the coating preparation process and generated while the specimens cooled down from the high oxidation temperature prevented the oxidation of carbon/carbon composites. X-ray computed tomography was used to obtain three-dimensional images revealing internal damage caused by spallation and open holes on the coating. Stress induced by heating and cooling caused the formation, growth and coalescence of cracks, which in turn led to exfoliation of the coating and subsequent failure of oxidation protection.
Open AccessCrack Evolution and Oxidation Failure Mechanism of a SiC-Ceramic Coating Reactively Sintered on Carbon/Carbon Composites
A SiC ceramic coating was prepared on carbon/carbon composites by pack cementation. The phase composition and microstructure of the coated specimens were characterized using X-ray diffraction instrument and scanning electron microscope. The results showed that the mass-loss percentage of the coated specimen was 9.5% after being oxidized for 20 h. The oxidation failure of the SiC ceramic coating at 1773 K was analysed by non-destructive X-ray computed tomography. The effective self-healing of cracks with widths below 12.7 μm introduced during the coating preparation process and generated while the specimens cooled down from the high oxidation temperature prevented the oxidation of carbon/carbon composites. X-ray computed tomography was used to obtain three-dimensional images revealing internal damage caused by spallation and open holes on the coating. Stress induced by heating and cooling caused the formation, growth and coalescence of cracks, which in turn led to exfoliation of the coating and subsequent failure of oxidation protection.
- Open Access
Epitaxial Grown Carbon Nanotubes Reinforced Pyrocarbon Matrix in C/C Composites with Improved Mechanical Properties
In order to achieve the highly efficient preparation of high-performance carbon/carbon (C/C) composites, epitaxial grown carbon nanotubes (CNTs) and a pyrocarbon matrix were simultaneously synthesized to fabricate CNT-reinforced C/C composites (CC/C composites). With precise control of the temperature gradient, CNTs and the pyrocarbon matrix could grow synchronously within a 2D needle-punched carbon fiber preform. Surprisingly, the CNTs remained intact within the pyrocarbon matrix at the nano-level, and the CNT-reinforced nano-pyrocarbon matrix was compact, with virtually no gaps and pores, which were tightly connected with the carbon fibers without cracks. Based on the results of Raman analysis, there is less residual stress in the CNT-reinforced pyrocarbon matrix and carbon fibers, and less of a mismatch between the coefficient and thermal expansion. Additionally, CC/C composites fabricated by this method could achieve a low density, open porosity with a large size, and improved mechanical properties. More importantly, our work provides a rational design strategy for the highly efficient preparation and structural design of high-performance CNT-einforced C/C composites.
Open AccessEpitaxial Grown Carbon Nanotubes Reinforced Pyrocarbon Matrix in C/C Composites with Improved Mechanical Properties
In order to achieve the highly efficient preparation of high-performance carbon/carbon (C/C) composites, epitaxial grown carbon nanotubes (CNTs) and a pyrocarbon matrix were simultaneously synthesized to fabricate CNT-reinforced C/C composites (CC/C composites). With precise control of the temperature gradient, CNTs and the pyrocarbon matrix could grow synchronously within a 2D needle-punched carbon fiber preform. Surprisingly, the CNTs remained intact within the pyrocarbon matrix at the nano-level, and the CNT-reinforced nano-pyrocarbon matrix was compact, with virtually no gaps and pores, which were tightly connected with the carbon fibers without cracks. Based on the results of Raman analysis, there is less residual stress in the CNT-reinforced pyrocarbon matrix and carbon fibers, and less of a mismatch between the coefficient and thermal expansion. Additionally, CC/C composites fabricated by this method could achieve a low density, open porosity with a large size, and improved mechanical properties. More importantly, our work provides a rational design strategy for the highly efficient preparation and structural design of high-performance CNT-einforced C/C composites.
- Open Access
- 1 November 2018
- Published by MDPI AG in Nanomaterials
- Vol. 8 (11) , 894
3C-SiC Nanowires In-Situ Modified Carbon/Carbon Composites and Their Effect on Mechanical and Thermal Properties
An in-situ, catalyst-free method for synthesizing 3C-SiC ceramic nanowires (SiCNWs) inside carbon–carbon (C/C) composites was successfully achieved. Obtained samples in different stages were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Raman scattering spectroscopy. Results demonstrated that the combination of sol-gel impregnation and carbothermal reduction was an efficient method for in-situ SiCNW synthesis, inside C/C composites. Thermal properties and mechanical behaviors—including out-of-plane and in-plane compressive strengths, as well as interlaminar shear strength (ILLS) of SiCNW modified C/C composites—were investigated. By introducing SiCNWs, the initial oxidation temperature of C/C was increased remarkably. Meanwhile, out-of-plane and in-plane compressive strengths, as well as interlaminar shear strength (ILLS) of C/C composites were increased by 249.3%, 109.2%, and 190.0%, respectively. This significant improvement resulted from simultaneous reinforcement between the fiber/matrix (F/M) and matrix/matrix (M/M) interfaces, based on analysis of the fracture mechanism.
- 1 November 2018
- Published by MDPI AG in Nanomaterials
- Vol. 8 (11) , 894
Open Access3C-SiC Nanowires In-Situ Modified Carbon/Carbon Composites and Their Effect on Mechanical and Thermal Properties
An in-situ, catalyst-free method for synthesizing 3C-SiC ceramic nanowires (SiCNWs) inside carbon–carbon (C/C) composites was successfully achieved. Obtained samples in different stages were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Raman scattering spectroscopy. Results demonstrated that the combination of sol-gel impregnation and carbothermal reduction was an efficient method for in-situ SiCNW synthesis, inside C/C composites. Thermal properties and mechanical behaviors—including out-of-plane and in-plane compressive strengths, as well as interlaminar shear strength (ILLS) of SiCNW modified C/C composites—were investigated. By introducing SiCNWs, the initial oxidation temperature of C/C was increased remarkably. Meanwhile, out-of-plane and in-plane compressive strengths, as well as interlaminar shear strength (ILLS) of C/C composites were increased by 249.3%, 109.2%, and 190.0%, respectively. This significant improvement resulted from simultaneous reinforcement between the fiber/matrix (F/M) and matrix/matrix (M/M) interfaces, based on analysis of the fracture mechanism.
- 19 September 2011
- Published by Wiley
- p. 85-90
An Yb 2 Si 2 O 7 Oxidation Resistance Coating for C/C Composites by Supersonic Plasma Spray
- 19 September 2011
- Published by Wiley
- p. 85-90
An Yb 2 Si 2 O 7 Oxidation Resistance Coating for C/C Composites by Supersonic Plasma Spray
- 20 August 2011
- Published by China Science Publishing & Media Ltd. in Journal of Inorganic Materials
- Vol. 26 (8) , 847-851
Influence of Interlayer’s Thickness on Strength of Joints between LAS Glass-ceramic and Carbon/Carbon Composites
Surface modified carbon/carbon(C/C) composites were joined to Li2CO3-Al2O3-SiO2(LAS) glass ceramic by hot pressing bonding using MgO-Al2O3-SiO2(MAS) glass with different thicknesses as the joining material.The effect of interlayer thickness on the joint strength was discussed.Microstructures and mor-phologies of the as-received joints and fractured surfaces were characterized by scanning electron microscope.The results indicated that the LAS glass was directly joined to the surface modified C/C composites at 1200℃,and the room-temperature shear strength of the joints was only 10MPa,due to its poor wettability with base material.When the MAS glass was applied as interlayer,the joint shear strength increased at first and then decreased with the increase of the interlayer thickness.The maximum value of the shear strength reached 26.61MPa when interlayer thickness was 80μm.
- 20 August 2011
- Published by China Science Publishing & Media Ltd. in Journal of Inorganic Materials
- Vol. 26 (8) , 847-851
Influence of Interlayer’s Thickness on Strength of Joints between LAS Glass-ceramic and Carbon/Carbon Composites
Surface modified carbon/carbon(C/C) composites were joined to Li2CO3-Al2O3-SiO2(LAS) glass ceramic by hot pressing bonding using MgO-Al2O3-SiO2(MAS) glass with different thicknesses as the joining material.The effect of interlayer thickness on the joint strength was discussed.Microstructures and mor-phologies of the as-received joints and fractured surfaces were characterized by scanning electron microscope.The results indicated that the LAS glass was directly joined to the surface modified C/C composites at 1200℃,and the room-temperature shear strength of the joints was only 10MPa,due to its poor wettability with base material.When the MAS glass was applied as interlayer,the joint shear strength increased at first and then decreased with the increase of the interlayer thickness.The maximum value of the shear strength reached 26.61MPa when interlayer thickness was 80μm.
- 20 February 2010
- Published by China Science Publishing & Media Ltd. in Journal of Inorganic Materials
- Vol. 25 (2) , 173-176
Study on the Microstructures and Mechanical Properties of 2D C/C Composites
The 2D C/C composites with different microstructures were fabricated by isothermal-isobaric chemical vapor infiltration (ICVI). The mechanical properties of the 2D C/C composites were investigated by 3-point bending tests. The microstructures of the pyrocarbon matrix were observed by polarized light microscope (PLM), scanning electron microscope (SEM), transmission electron microscope (TEM) combining selected area electron diffraction (SAED). The results show that 2D C/C composites with dominant layered-HT pyrocarbon matrix exhibit a pseudo-plastic failure behavior. The flake-like fragments MT and granular-like particles ISO are in favor of increasing the flexural strength of the materials. It exists a good interfacial bonding between the fiber and HT layer. The non-HT layer does not exist at the interface, but the orientation angle (OA) of the matrix slightly increases
- 20 February 2010
- Published by China Science Publishing & Media Ltd. in Journal of Inorganic Materials
- Vol. 25 (2) , 173-176
Study on the Microstructures and Mechanical Properties of 2D C/C Composites
The 2D C/C composites with different microstructures were fabricated by isothermal-isobaric chemical vapor infiltration (ICVI). The mechanical properties of the 2D C/C composites were investigated by 3-point bending tests. The microstructures of the pyrocarbon matrix were observed by polarized light microscope (PLM), scanning electron microscope (SEM), transmission electron microscope (TEM) combining selected area electron diffraction (SAED). The results show that 2D C/C composites with dominant layered-HT pyrocarbon matrix exhibit a pseudo-plastic failure behavior. The flake-like fragments MT and granular-like particles ISO are in favor of increasing the flexural strength of the materials. It exists a good interfacial bonding between the fiber and HT layer. The non-HT layer does not exist at the interface, but the orientation angle (OA) of the matrix slightly increases
- 1 October 2009
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 24 (5) , 728-731
Fabrication of isotropic pyrocarbon at 1400 °C by thermal gradient chemical vapor deposition apparatus
- 1 October 2009
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 24 (5) , 728-731
Fabrication of isotropic pyrocarbon at 1400 °C by thermal gradient chemical vapor deposition apparatus