KMKnut Merte

Knut Merte

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Knut Merte has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental and Clinical Evaluation of a Self-etching and an Etch-and-Rinse Adhesive System

    by Matthias Häfer, Hartmut Schneider, Stefan Rupf, Ingeborg Busch, Andreas Fuchß, Ilka Merte, Holger Jentsch, Rainer Haak, Knut Merte

    To assess the one-step self-etching adhesive iBond Gluma inside (1-SE) and the two-step etch-and rinse adhesive Gluma Comfort Bond (2-ER), both used in combination with the fine particle hybrid composite Venus, in a laboratory and in a prospective clinical study. In the in vitro study, tooth-composite interaction, microleakage, and adhesive failure of 8 Class V restorations per system were evaluated by light and scanning electron microscopy. In the in vivo study, 90 paired Class III/IV restorations were scored over 48 months (modified USPHS criteria). Cumulative failure rates (CFR) were calculated. In vitro, microleakage and adhesive failure at enamel margins were significantly increased with 1-SE in comparison with 2-ER. With 1-SE, micromechanical interlocking at enamel was reduced and pores within the adhesive layer arose. In vivo, after 48 months with 1-SE, decreased marginal integrity and an increased number of dark marginal color lines were observed. Because the results of the 4-year clinical study showed lower esthetics and marginal integrity for the 1-SE adhesive, its use should be viewed critically, which is in line with the reduced enamel-adhesive-composite interaction found in vitro.


  • Tooth–composite interface from specific and nonspecific adhesive restorative systems

    by Gitte Haßhoff, Hartmut Schneider, Knut Merte

    The aim of this in vitro study was to do a morphological comparison of tooth/composite interface by means of three composite systems: (1) a specific formulated primer adhesive and Organically Modified Ceramics (ORMOCER) composite, (2) an universal self‐etching adhesive and the same ORMOCER composite, (3) and the same universal adhesive used for Group 2 and a fine‐particle hybrid resin composite. The rational for this study was based on the recommendations from manufacturers that nonspecific dentin bonding agents can be used with ORMOCER. Twenty‐one Class II cavities were prepared in extracted third molars. Seven randomly assigned teeth were restored with one of the three methods according to the instructions provided by the manufacturer. Following completion of the restorations, the teeth were sectioned and evaluated by means of scanning electron microscopy for evaluation of interfacial morphology and light microscopy for the determination of microleakage. The last was scored as being present or absent. The best results were observed using method 1, in which a special primer adhesive and ORMOCER composite was used. In this group there were statistically significant fewer gaps in enamel (4.7± 7.5%) and dentin (22.8 ± 7.4%) compared to the other two groups (Group 2: enamel 21.1 ± 8.3% and dentin 66.3 ± 17.3%; and Group 3: enamel 40.6 ± 35.2% and dentin 89.4 ± 13.3%). The interfaceof method 2, universal self‐etching adhesive and ORMOCER, was of a lesser quality than Group 1. Within the limitations of this study the recommendation is made to use the ORMOCER tested in this experiment with the matching specifically formulated primer adhesive system. A lack of adhesion as well as microleakage, were prominent features for Groups 2 and 3. From the data of this study the practitioner is cautioned not to indiscriminately exchange specific dentin bonding agents for nonspecific ones. Considering the shear endless number of possible combinations and the numerous different tests that would be required to test these all, selection of different combinations will remain a theoretical exercise. © 2004 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 71B: 38–45, 2004


    • 1 January 2004
      • Vol. 114  (11) , 1124-31

    [Is it necessary to assess experimentally and clinically restorative materials already on the market?].

    by Ilka Merte, Hartmut Schneider, Knut Merte

    The precondition for introducing medical products, e.g. new filling materials, in the European Union is their safety, not their clinical reliability. The latter arises from longitudinal studies and is assessed on the basis of available standards or, if not existant, on formulated quality guidelines. In the case of the specific products Ariston Liner and Ariston pHc (Vivadent, Schaan, FL), designed as an amalgam substitute, the material combination did not correspond to the Swiss standard 2 of restorative dentistry. Although after a short-term application testing on caries free premolars the pulp and dentin were free from inflammation and bacteria, the material combination clinically failed within the 18 months control period with a cumulative failure rate of 16.1% due to marginal caries. After six months of function the subjectively assessed sensitivity tended to increase. Gap formations and porous zones were detected in the composite-tooth-interface in vitro as well as in vivo. Neither the lining, designed to ensure the passage of cations and anions out of the filling material, nor the concept of an adequate caries protective effect proved successful. Marginal caries and hypersensitivity of teeth were the main reasons for the replacement of this amalgam substitute. The specific material combination was withdrawn from the market. As long as laboratory methods cannot substitute clinical evaluations, the introduction of new materials or systems into the market should be supported by short-term clinical studies and the further quality assessment should result from intermediate to long-term longitudinal studies. In this respect guidelines are valuable, such as the Swiss guidelines concerning materials as amalgam substitute.