FBFerhat Bouzerara

Ferhat Bouzerara

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ferhat Bouzerara has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Elaboration of porous gehlenite and anorthite based ceramics using low price raw materials

    by F. Zenikheri, A. Harabi, B. Boudaira, F. Bouzerara, A. Guechi, S.-E. Barama, L. Foughali, N. Karboua

    Porous ceramics of good quality cost a lot in the world market, which has limited their use in developing countries. This is why this work was mainly devoted to prepare low-cost and good quality ceramics, using kaolin (DD2 type) and calcite (CaCO3) available in abundance in Algeria. Based on previous results, 28 wt% CaCO3 ceramic was selected. The presence of CaCO3 favors to achieve porous samples characterized by a high percentage of porosity due to the CO2 release and CaO formation during its calcination at about 700 °C. The choice of these raw materials is based on their natural abundance (low price). It has been found that the samples had interesting characteristics: average pore size between 2.87 and 6.50 μm and porosity between 53 and 57%. It has also been found that the manufactured membrane supports are mainly constituted of gehlenite and anorthite phases. Moreover, the pore size distribution was mono-modal type. The surface and cross-section morphologies observed through a scanning electron microscope were also homogeneous and do not present any possible macro-defects (cracks, etc.).


  • Open Access

    Preparation and characterization of ZnO microfiltration membrane and its support using kaolin (DD3) and CaCO3

    by B. Boudaira, A. Harabi, F. Bouzerara, S. Condom, F. Zenikheri, A. Guechi, L. Foughali, N. Karboua

    The objective of the present paper was to prepare a ceramic support with membrane. Tubular ceramic supports prepared from kaolin (DD3) and calcium carbonate with 6 and 10 mm inner and outer diameters, respectively, were extruded and sintered at 1200 °C. It has been found that sintered supports had interesting characteristics: average pore size of about 5µm, porosity of about 50%, and monomodal pore size distribution. This support was used to be substrate for a membrane layer of microfiltration. This membrane layer was elaborated from zinc oxide, using slip casting technique. The specimens were subsequently sintered at 1000 °C. The microstructure and porosity as well as the permeability have also been studied. It has been found that the average pore size was about 1.2µm, the layer thickness was ~33µm, and the water permeability measured was about 880 L.h-1.m-2.bar-1.


  • Open Access

    Elaboration and characterization of tubular supports for membranes filtration

    by A. Guechi, A. Harabi, S. Condoum, F. Zenikheri, B. Boudaira, F. Bouzerara, L. Foughali

    The use of ceramic membranes has many advantages, such as high thermal and chemical stability, pressure resistance, long lifetime, good resistance to fouling, and the ease of cleaning. Up to now, the production of industrial membrane supports uses a limited choice of materials. As a consequence, the price of ceramic membranes is high and a significant effort was provided in this last years in the membrane technology field in order to find new porous ceramic materials with clays and kaolins. These materials are in abundance and need lower sintering temperatures than metal oxide materials. In this work, the tubular supports for membranes filtration was manufactured from kaolin and lime extracted from limestone. The influence of the relative low sintering temperature ranging from 800 to 1,100°C on the porosity, the average pore size (APS), a pore size distribution, and a strength of supports have been investigated. Additionally, the APS and the porosity values were about 8 μm and 47% for supports sintered at 1,000°C. Besides this, three-point flexural strength values were ranged from 30 to 53 MPa for samples sintered at sintering temperatures situated between 1,000 and 1,100°C, respectively.


  • Open Access

    Preparation and characterization of membrane supports for microfiltration and ultrafiltration using kaolin (DD2) and CaCO3

    by Boukhemis Boudaira, Abdelhamid Harabi, Ferhat Bouzerara, Fahima Zenikheri, Lazhar Foughali, Abdelkarim Guechi

    The ceramic products are extremely interesting in the field of the membrane supports because of their mechanical resistance, chemical inertia, long working life, and thermal stability. This work is mainly focussed on ceramic supports rather than its deposited membranes because it constitutes about 99% of the filter mass. Therefore, replacing the more expensive starting materials (Al2O3) by other low cost raw materials (kaolin and calcite) for supports fabrication is significantly important. Consequently, the supports for microfiltration (MF), ultrafiltration, and nanofiltration were prepared with local kaolin (DD2) and calcite mixtures. The choice of these raw materials is based on their natural abundance (low price). These supports were made by extrusion technique order to obtain tubular supports which were afterward sintered at 1,150°C for 2 h. It has been found that supports had interesting characteristics; an average pore size of about 4 μm, a porosity ratio around 50.5%, and a three-point flexural strength ≈28 MPa. Moreover, the pore size distribution was almost mono-modal type. The surface and the cross-section morphologies observed through a scanning electron microscope were also homogeneous and do not present any possible macro defects (cracks, etc.) These supports were selected to be substrates for the membrane layers used in MF.


  • Optical and electrical study of deformed hydrogenated bulk Cd0.96Zn0.04Te single crystal

    by F. Lmai, N. Brihi, Z. Takkouk, K. Guergouri, F. Bouzerara, M. Hage-Ali

    The effect of hydrogenation on defects associated with dislocations has been studied in the p-type Cd0.96Zn0.04Te (CZT) semiconductor, grown by the horizontal Bridgman method, with the help of current I(V), capacity C(V) measurements, photoluminescence spectra, and cathodoluminescence imaging. To generate dislocations by plastic deformation we have used a Vickers microhardness instrument on several cadmium (Cd)(111) and telluride (Te)(1¯1¯1¯)CZT faces. Hydrogenation was carried out by exposure of the samples to hydrogen plasma at 150 °C and 3 mbar for 3 h. The analysis of the results obtained confirms both the reduction of the acceptor concentration, that acceptors may be passivated by formation of neutral complexes with hydrogen, and that the majority defect on each face is the tellurium vacancy, VTe. A reduction of the broadband at 1.547 eV (VCd2−−D) is observed, while the donor bound exciton D0X is increased on the Cd face and finally, it seems that the hydrogen stabilizes dislocations and prevents their removal.