Ville Polojärvi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ville Polojärvi has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Antti Tukiainen
Faculty of Engineering and Natural Sciences, Tampere University, Tampere, Finland
9 shared publications - Mircea Guina
Tampere University
9 shared publications - Arto Aho
Winse Power Oy 2 , Tekniikankatu 1, Tampere
7 shared publications - Marianna Raappana
Optoelectronics Research Centre, Physics Unit, Tampere University, P.O. Box 692, FI-33014, Tampere, Finland
4 shared publications - Timo Aho
Modulight Corporation 3 , Hermiankatu 22, Tampere
4 shared publications - Riku Isoaho
Tampere Univ, Fac Engn & Nat Sci, Optoelect Res Ctr, Phys Unit, POB 692, FIN-33014 Tampere, Finland
3 shared publications
Latest Publications
- Open Access
- 1 July 2021
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 226, 111097
Nonselective etching of As and P based III‒V solar cell heterostructures with aqueous solutions of HIO3 and HCl
- 1 July 2021
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 226, 111097
Open AccessNonselective etching of As and P based III‒V solar cell heterostructures with aqueous solutions of HIO3 and HCl
- Open Access
- 9 March 2021
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 29 (7) , 869-875
Wide spectral coverage (0.7–2.2 eV) lattice‐matched multijunction solar cells based on AlGaInP, AlGaAs and GaInNAsSb materials
We report on the progress in developing lattice‐matched GaAs‐based solar cells with focus on developing AlGaInP, AlGaAs, and GaInNAsSb materials, aiming at achieving a wide spectral coverage, that is, 0.7–2.2 eV. To this end, we first benchmark the performance of an upright four‐junction GaInP/GaAs/GaInNAsSb/GaInNAsSb solar cells grown by molecular beam epitaxy on p‐GaAs substrates with bandgaps of 1.88, 1.42, 1.17, and 0.93 eV, respectively. The four‐junction cell exhibited an efficiency of ~39% at 560‐sun illumination while showing good electrical performance even up to 1000 suns. As a first step to further improve the efficiency toward 50% level, we demonstrate AlGaInP (>2 eV) and GaInNAsSb (<0.8 eV) subcells. We prove that AlGaInP cells with 0.1 Al composition would exhibit current‐matching condition when being incorporated in a five‐junction architecture together with two GaInNAsSb bottom and AlGaAs top junctions. Furthermore, current matching required for a six‐junction tandem architecture is achieved for an Al composition of 0.26. Overall, the results open a practical path toward fabrication of lattice‐matched solar cells with more than four junctions.
- 9 March 2021
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 29 (7) , 869-875
Open AccessWide spectral coverage (0.7–2.2 eV) lattice‐matched multijunction solar cells based on AlGaInP, AlGaAs and GaInNAsSb materials
We report on the progress in developing lattice‐matched GaAs‐based solar cells with focus on developing AlGaInP, AlGaAs, and GaInNAsSb materials, aiming at achieving a wide spectral coverage, that is, 0.7–2.2 eV. To this end, we first benchmark the performance of an upright four‐junction GaInP/GaAs/GaInNAsSb/GaInNAsSb solar cells grown by molecular beam epitaxy on p‐GaAs substrates with bandgaps of 1.88, 1.42, 1.17, and 0.93 eV, respectively. The four‐junction cell exhibited an efficiency of ~39% at 560‐sun illumination while showing good electrical performance even up to 1000 suns. As a first step to further improve the efficiency toward 50% level, we demonstrate AlGaInP (>2 eV) and GaInNAsSb (<0.8 eV) subcells. We prove that AlGaInP cells with 0.1 Al composition would exhibit current‐matching condition when being incorporated in a five‐junction architecture together with two GaInNAsSb bottom and AlGaAs top junctions. Furthermore, current matching required for a six‐junction tandem architecture is achieved for an Al composition of 0.26. Overall, the results open a practical path toward fabrication of lattice‐matched solar cells with more than four junctions.
- 8 January 2021
- Published by IOP Publishing in Nanotechnology
- Vol. 32 (13) , 130001
GaAs surface passivation for InAs/GaAs quantum dot based nanophotonic devices
Several passivation techniques are developed and compared in terms of their ability to preserve the optical properties of close-to-surface InAs/GaAs quantum dots (QDs). In particular, the influence of N-passivation by hydrazine chemical treatment, N-passivation by hydrazine followed by atomic layer deposition (ALD) of AlO x and use of AlN x deposited by plasma-enhanced ALD are reported. The effectiveness of the passivation is benchmarked by measuring the emission linewidths and decay rates of photo-carriers for the near-surface QDs. All three passivation mechanisms resulted in reducing the oxidation of Ga and As atoms at the GaAs surface and consequently in enhancing the room-temperature photoluminescence (PL) intensity. However, long-term stability of the passivation effect is exhibited only by the hydrazine + AlO x process and more significantly by the AlN x method. Moreover, in contrast to the results obtained from hydrazine-based methods, the AlN x passivation strongly reduces the spectral diffusion of the QD exciton lines caused by charge fluctuations at the GaAs surface. The AlN x passivation is found to reduce the surface recombination velocity by three orders of magnitude (corresponding to an increase of room-temperature PL signal by ∼1030 times). The reduction of surface recombination velocity is demonstrated on surface-sensitive GaAs (100) and the passivating effect is stable for more than one year. This effective method of passivation, coupled with its stability in time, is extremely promising for practical device applications such as quantum light sources based on InAs/GaAs QDs positioned in small-volume photonic cavities and hence in the proximity of GaAs-air interface.
- 8 January 2021
- Published by IOP Publishing in Nanotechnology
- Vol. 32 (13) , 130001
GaAs surface passivation for InAs/GaAs quantum dot based nanophotonic devices
Several passivation techniques are developed and compared in terms of their ability to preserve the optical properties of close-to-surface InAs/GaAs quantum dots (QDs). In particular, the influence of N-passivation by hydrazine chemical treatment, N-passivation by hydrazine followed by atomic layer deposition (ALD) of AlO x and use of AlN x deposited by plasma-enhanced ALD are reported. The effectiveness of the passivation is benchmarked by measuring the emission linewidths and decay rates of photo-carriers for the near-surface QDs. All three passivation mechanisms resulted in reducing the oxidation of Ga and As atoms at the GaAs surface and consequently in enhancing the room-temperature photoluminescence (PL) intensity. However, long-term stability of the passivation effect is exhibited only by the hydrazine + AlO x process and more significantly by the AlN x method. Moreover, in contrast to the results obtained from hydrazine-based methods, the AlN x passivation strongly reduces the spectral diffusion of the QD exciton lines caused by charge fluctuations at the GaAs surface. The AlN x passivation is found to reduce the surface recombination velocity by three orders of magnitude (corresponding to an increase of room-temperature PL signal by ∼1030 times). The reduction of surface recombination velocity is demonstrated on surface-sensitive GaAs (100) and the passivating effect is stable for more than one year. This effective method of passivation, coupled with its stability in time, is extremely promising for practical device applications such as quantum light sources based on InAs/GaAs QDs positioned in small-volume photonic cavities and hence in the proximity of GaAs-air interface.
- 10 December 2018
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 27 (4) , 299-305
Lattice‐matched four‐junction tandem solar cell including two dilute nitride bottom junctions
Monolithic four‐junction solar cells incorporating two dilute nitride (GaInNAsSb) bottom junctions are reported. The dilute nitride junctions have band gaps of 0.9 and 1.2 eV, while the top junctions have band gaps of 1.4 and 1.9 eV. By using experimental‐based parametrization, it was estimated that the four‐junction solar cell could theoretically exhibit efficiency levels of 34.7% at one sun, 43.2% at 100 suns, and 46.4% at 1000 suns for AM1.5D illumination. The most challenging subcell in terms of fabrication is the GaInNAsSb bottom junction with 0.9 eV band gap. For this subcell, a background doping level down to 5 × 10 14 cm −3 and a high charge carrier lifetime up to 2 to 4 nanoseconds are reported, which reflects high values for current and voltage. An experimental AlGaAs/GaAs/GaInNAsSb/GaInNAsSb solar cell structure was fabricated by molecular beam epitaxy. At one‐sun AM1.5D illumination, the experimental cell exhibited an efficiency of 25%, an average quantum efficiency of 91%, and an open circuit voltage, which is about 87% of the estimated potential. The cell exhibited maximum efficiency of 37% at 100‐sun concentration.
- 10 December 2018
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 27 (4) , 299-305
Lattice‐matched four‐junction tandem solar cell including two dilute nitride bottom junctions
Monolithic four‐junction solar cells incorporating two dilute nitride (GaInNAsSb) bottom junctions are reported. The dilute nitride junctions have band gaps of 0.9 and 1.2 eV, while the top junctions have band gaps of 1.4 and 1.9 eV. By using experimental‐based parametrization, it was estimated that the four‐junction solar cell could theoretically exhibit efficiency levels of 34.7% at one sun, 43.2% at 100 suns, and 46.4% at 1000 suns for AM1.5D illumination. The most challenging subcell in terms of fabrication is the GaInNAsSb bottom junction with 0.9 eV band gap. For this subcell, a background doping level down to 5 × 10 14 cm −3 and a high charge carrier lifetime up to 2 to 4 nanoseconds are reported, which reflects high values for current and voltage. An experimental AlGaAs/GaAs/GaInNAsSb/GaInNAsSb solar cell structure was fabricated by molecular beam epitaxy. At one‐sun AM1.5D illumination, the experimental cell exhibited an efficiency of 25%, an average quantum efficiency of 91%, and an open circuit voltage, which is about 87% of the estimated potential. The cell exhibited maximum efficiency of 37% at 100‐sun concentration.
- 1 May 2018
- Published by Elsevier in Corrosion Science
- Vol. 136, 268-274
Wet etching of dilute nitride GaInNAs, GaInNAsSb, and GaNAsSb alloys lattice-matched to GaAs
- 1 May 2018
- Published by Elsevier in Corrosion Science
- Vol. 136, 268-274
Wet etching of dilute nitride GaInNAs, GaInNAsSb, and GaNAsSb alloys lattice-matched to GaAs
- 1 November 2015
- Published by Elsevier in Scripta Materialia
- Vol. 108, 122-125
Optical properties and thermionic emission in solar cells with InAs quantum dots embedded within GaNAs and GaInNAs
- 1 November 2015
- Published by Elsevier in Scripta Materialia
- Vol. 108, 122-125
Optical properties and thermionic emission in solar cells with InAs quantum dots embedded within GaNAs and GaInNAs
- Open Access
- 17 February 2014
- Published by Springer Nature in Discover Nano
- Vol. 9 (1) , 80
Dynamics of time-resolved photoluminescence in GaInNAs and GaNAsSb solar cells
We report a time-resolved photoluminescence study for GaInNAs and GaNAsSb p-i-n bulk solar cells grown on GaAs(100). In particular, we studied the extent to which the carrier lifetime decreases with the increase of N content. Rapid thermal annealing proved to significantly increase the decay times by a factor of 10 to 12 times, for both GaInNAs and GaNAsSb heterostructures, while for the 1-eV bandgap GaNAsSb structure, grown at the same growth conditions as the GaInNAs, the photoluminescence decay time remained slightly below 100 ps after annealing; the approximately 1.15-eV GaInNAs p-i-n solar cell exhibited a lifetime as long as 900 ps.
- 17 February 2014
- Published by Springer Nature in Discover Nano
- Vol. 9 (1) , 80
Open AccessDynamics of time-resolved photoluminescence in GaInNAs and GaNAsSb solar cells
We report a time-resolved photoluminescence study for GaInNAs and GaNAsSb p-i-n bulk solar cells grown on GaAs(100). In particular, we studied the extent to which the carrier lifetime decreases with the increase of N content. Rapid thermal annealing proved to significantly increase the decay times by a factor of 10 to 12 times, for both GaInNAs and GaNAsSb heterostructures, while for the 1-eV bandgap GaNAsSb structure, grown at the same growth conditions as the GaInNAs, the photoluminescence decay time remained slightly below 100 ps after annealing; the approximately 1.15-eV GaInNAs p-i-n solar cell exhibited a lifetime as long as 900 ps.
- Open Access
- 5 February 2014
- Published by Springer Nature in Discover Nano
- Vol. 9 (1) , 61
Performance assessment of multijunction solar cells incorporating GaInNAsSb
We have measured the characteristics of molecular beam epitaxy grown GaInNAsSb solar cells with different bandgaps using AM1.5G real sun illumination. Based on the solar cell diode characteristics and known parameters for state-of-the-art GaInP/GaAs and GaInP/GaAs/Ge cells, we have calculated the realistic potential efficiency increase for GaInP/GaAs/GaInNAsSb and GaInP/GaAs/GaInNAsSb/Ge multijunction solar cells for different current matching conditions. The analyses reveal that realistic GaInNAsSb solar cell parameters, render possible an extraction efficiency of over 36% at 1-sun AM1.5D illumination.
- 5 February 2014
- Published by Springer Nature in Discover Nano
- Vol. 9 (1) , 61
Open AccessPerformance assessment of multijunction solar cells incorporating GaInNAsSb
We have measured the characteristics of molecular beam epitaxy grown GaInNAsSb solar cells with different bandgaps using AM1.5G real sun illumination. Based on the solar cell diode characteristics and known parameters for state-of-the-art GaInP/GaAs and GaInP/GaAs/Ge cells, we have calculated the realistic potential efficiency increase for GaInP/GaAs/GaInNAsSb and GaInP/GaAs/GaInNAsSb/Ge multijunction solar cells for different current matching conditions. The analyses reveal that realistic GaInNAsSb solar cell parameters, render possible an extraction efficiency of over 36% at 1-sun AM1.5D illumination.
- 13 September 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 97 (11) , 111109
Effects of (NH4)2S and NH4OH surface treatments prior to SiO2 capping and thermal annealing on 1.3 μm GaInAsN/GaAs quantum well structures
We report the influence of and surface treatments prior to capping and subsequent rapid thermal annealing, on optical properties of GaInAsN/GaAs quantum-well (QW) structures. We observed an increase in QW photoluminescence (PL) emission for the treated samples as compared to the untreated sample. After annealing, also the treated sample showed significant improvement in PL. The treatments were also found to decrease the In out-diffusion and reduce the blueshift upon annealing. The PL results are discussed with x-ray diffraction and x-ray photoemission data from , in particular, with changes found in spectra.- 13 September 2010
- Published by AIP Publishing in Applied Physics Letters
- Vol. 97 (11) , 111109
Effects of (NH4)2S and NH4OH surface treatments prior to SiO2 capping and thermal annealing on 1.3 μm GaInAsN/GaAs quantum well structures
We report the influence of and surface treatments prior to capping and subsequent rapid thermal annealing, on optical properties of GaInAsN/GaAs quantum-well (QW) structures. We observed an increase in QW photoluminescence (PL) emission for the treated samples as compared to the untreated sample. After annealing, also the treated sample showed significant improvement in PL. The treatments were also found to decrease the In out-diffusion and reduce the blueshift upon annealing. The PL results are discussed with x-ray diffraction and x-ray photoemission data from , in particular, with changes found in spectra.