Hiroyuki Tsuda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hiroyuki Tsuda has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Fumi Nakamura
National Institute of Advanced Industrial Science and Technology (AIST)
1 shared publication - Hideaki Asakura
Graduate School of Science and Technology, Keio University, 12869 Yokohama, Kanagawa, Japan
1 shared publication Hirokazu Takenouchi
H. Tsudais with Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama, Kanagawa 223-8522, Japan.H. Takenouchi is with NTT Photonics Laboratories, 3-1 Morinosato-Wakamiya, Atsugi, Kanagawa 243-0198, Japan
1 shared publication- Hirokazu Takenouchi
NTT Photonics Laboratories, 3-1 Morinosato-Wakamiya, Atsugi, Kanagawa, 243-0198 Japan
1 shared publication - Hitoshi Kawashima
Ultrafast Photonic Devices Lab., AIST, Tsukuba, Ibaraki Japan 305-8568
1 shared publication - Kazuhiro Ikeda
National Institute of Advanced Industrial Science and Technology (AIST)
1 shared publication
Latest Publications
- Open Access
- 25 April 2023
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Electronics Express
- Vol. 20 (8) , 20230082
Broadband optical packet generation by multiplexing signals using a bias tee
This paper presents a broadband optical packet generation method by multiplexing low- and high-frequency signals using a bias tee. The cut-off frequency of the bias tee, fc is optimized in terms of the eye-opening ratio for optical packet trains with different guard times and intervals. As a result, the optimal condition is observed to be fGT < fc < f1, and fc should be closer to fGT. (where fGT is the guard frequency and f1 is the high-pass cut-off frequency of a low-frequency amplifier). We implemented optical packet generation using a bias tee based on the simulation results and confirmed the effectiveness of this method.
- 25 April 2023
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Electronics Express
- Vol. 20 (8) , 20230082
Open AccessBroadband optical packet generation by multiplexing signals using a bias tee
This paper presents a broadband optical packet generation method by multiplexing low- and high-frequency signals using a bias tee. The cut-off frequency of the bias tee, fc is optimized in terms of the eye-opening ratio for optical packet trains with different guard times and intervals. As a result, the optimal condition is observed to be fGT < fc < f1, and fc should be closer to fGT. (where fGT is the guard frequency and f1 is the high-pass cut-off frequency of a low-frequency amplifier). We implemented optical packet generation using a bias tee based on the simulation results and confirmed the effectiveness of this method.
- 25 May 2022
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Electronics Express
- Vol. 19 (10) , 20220155
Design of an optical triode switch using phase-change material
An optical triode switch using phase change material (PCM) operating as a Mach-Zehnder interferometer (MZI) or as a directional coupler (DC) is proposed. The characteristics of optical triode switches are calculated by using finite-difference time-domain (FDTD) method. Ge2Sb2Te5 (GST) and Ge2Sb2Se4Te1 (GSST) are used as the PCM. In our calculation models, the signal light has a wavelength of 1550 nm, and the phase of the PCM is controlled by light with a wavelength of 1300 nm input into additional waveguides. In the MZI-type triode switch, PCM patches are laid on several crossings between the signal waveguides and the control waveguides. The DC-type triode switch consists of three parallel waveguides, and the control light is input to the center waveguide which has the PCM layer on it. The structures are optimized to have low loss and low crosstalk. In addition, the energy and pulse power required to change the phase are estimated for both types of switches.
- 25 May 2022
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in IEICE Electronics Express
- Vol. 19 (10) , 20220155
Design of an optical triode switch using phase-change material
An optical triode switch using phase change material (PCM) operating as a Mach-Zehnder interferometer (MZI) or as a directional coupler (DC) is proposed. The characteristics of optical triode switches are calculated by using finite-difference time-domain (FDTD) method. Ge2Sb2Te5 (GST) and Ge2Sb2Se4Te1 (GSST) are used as the PCM. In our calculation models, the signal light has a wavelength of 1550 nm, and the phase of the PCM is controlled by light with a wavelength of 1300 nm input into additional waveguides. In the MZI-type triode switch, PCM patches are laid on several crossings between the signal waveguides and the control waveguides. The DC-type triode switch consists of three parallel waveguides, and the control light is input to the center waveguide which has the PCM layer on it. The structures are optimized to have low loss and low crosstalk. In addition, the energy and pulse power required to change the phase are estimated for both types of switches.
- Open Access
- 31 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (8) , 2413-2420
Silicon Based 1 × M Wavelength Selective Switch Using Arrayed Waveguide Gratings With Fold-Back Waveguides
The design of a novel 1 x M fold-back type wavelength selective switch (WSS), which has fewer waveguide crossings than a conventional integrated WSS, is reported. The WSS is composed of interleavers, 1 M optical switches, and arrayed waveguide gratings (AWGs). Switches are combined with AWGs by fold-back waveguides, and each AWG works as both a demultiplexer and multiplexer thus avoiding center wavelength mismatch caused by fabrication errors. Waveguide crossings cause excess crosstalk and loss in lightwave circuits. By using a fold-back architecture the number of crossings can be reduced to less than half that of a conventional design. We discuss the operating principle, the design method, and the scalability of the fold-back type WSS. Furthermore, the switching operation of a 200 GHz spacing 20 channel 1 2 silicon WSS in a fold-back configuration on a 5 mm 10 mm SOI chip is demonstrated. This has 15 waveguide crossings in a path, of which six are additional crossings with monitor waveguides. The average insertion loss and average extinction ratio are 29.6 dB and 10.9 dB, respectively.
- 31 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (8) , 2413-2420
Open AccessSilicon Based 1 × M Wavelength Selective Switch Using Arrayed Waveguide Gratings With Fold-Back Waveguides
The design of a novel 1 x M fold-back type wavelength selective switch (WSS), which has fewer waveguide crossings than a conventional integrated WSS, is reported. The WSS is composed of interleavers, 1 M optical switches, and arrayed waveguide gratings (AWGs). Switches are combined with AWGs by fold-back waveguides, and each AWG works as both a demultiplexer and multiplexer thus avoiding center wavelength mismatch caused by fabrication errors. Waveguide crossings cause excess crosstalk and loss in lightwave circuits. By using a fold-back architecture the number of crossings can be reduced to less than half that of a conventional design. We discuss the operating principle, the design method, and the scalability of the fold-back type WSS. Furthermore, the switching operation of a 200 GHz spacing 20 channel 1 2 silicon WSS in a fold-back configuration on a 5 mm 10 mm SOI chip is demonstrated. This has 15 waveguide crossings in a path, of which six are additional crossings with monitor waveguides. The average insertion loss and average extinction ratio are 29.6 dB and 10.9 dB, respectively.
- 1 March 2017
- Published by Elsevier in Optics Communications
- Vol. 387, 135-140
Differential processing for frequency chirp measurement using optical pulse synthesizer
- 1 March 2017
- Published by Elsevier in Optics Communications
- Vol. 387, 135-140
Differential processing for frequency chirp measurement using optical pulse synthesizer
- 10 January 2002
- Published by Optica Publishing Group in Applied Optics
- Vol. 41 (2) , 290-297
Photonic encoder and decoder for optical code-division multiplexing with time-to-space converters and angle-multiplexed holograms
A photonic encoder–decoder pair for optical code-division multiplexing (OCDM) that uses time-to-space converters and angle-multiplexed holograms is proposed. The encoder converts the pulse from each input port into a specific code and multiplexes input signals into the output port. The hologram in the decoder generates a correlation waveform between the transmitted code and the recorded code. The performance of the OCDM system with the encoder–decoder pair is estimated. The maximum spectral efficiency for 8-bit length orthogonal codes in the worst case at a bit-error rate of 10-9 is 0.17 (bits/s)/Hz when the number of channels is 8.
- 10 January 2002
- Published by Optica Publishing Group in Applied Optics
- Vol. 41 (2) , 290-297
Photonic encoder and decoder for optical code-division multiplexing with time-to-space converters and angle-multiplexed holograms
A photonic encoder–decoder pair for optical code-division multiplexing (OCDM) that uses time-to-space converters and angle-multiplexed holograms is proposed. The encoder converts the pulse from each input port into a specific code and multiplexes input signals into the output port. The hologram in the decoder generates a correlation waveform between the transmitted code and the recorded code. The performance of the OCDM system with the encoder–decoder pair is estimated. The maximum spectral efficiency for 8-bit length orthogonal codes in the worst case at a bit-error rate of 10-9 is 0.17 (bits/s)/Hz when the number of channels is 8.