Yoshinori Yamaguchi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yoshinori Yamaguchi has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Keiko Sumitomo
SORST, Japan Science and Technology Agency Tokyo, Japan
3 shared publicationsMotoyasu Sasaki
Graduate School of Advanced Science and Engineering, Bioscience and Biomedical Engineering, Waseda University, Tokyo, Japan
2 shared publicationsHong Xu
National Key Laboratory of Nano/Micro Fabrication Technology, Research Institute for Micro/Nano Science and Technology, Shanghai Jiaotong University, Shanghai 200030, China
1 shared publication- Hongchen Gu
School of Biomedical Engineering, Med-X Research Institute, Shanghai Jiao Tong University, Shanghai 200030, China
1 shared publication Longlan Cui
National Key Laboratory of Nano/Micro Fabrication Technology, Research Institute for Micro/Nano Science and Technology, Shanghai Jiaotong University, Shanghai 200030, China
1 shared publicationPing He
National Key Laboratory of Nano/Micro Fabrication Technology, Research Institute for Micro/Nano Science and Technology, Shanghai Jiaotong University, Shanghai 200030, China
1 shared publication
Latest Publications
- 7 May 2009
- Published by Wiley in Electrophoresis
- Vol. 30 (9) , 1538-1543
Acetic acid denaturing for RNA capillary polymer electrophoresis
A strong denaturant to cleave intramolecular hydrogen bonds in RNA is required for RNA size separation in a small sample volume (in vitro sample preparation before electrophoresis. The baseline separation of RNA with a size of 100–10 000 nt was achieved in 25 min by “in‐capillary denaturing polymer electrophoresis” with the running buffer containing 2.0 M acetic acid. The resolution and the theoretical plates of RNA separation peaks were larger than those of the RNA separation in a conventional CGE with in vitro sample preparation by 7.0 M urea. In addition, we detected RNA peaks from the nucleic acids extracted from NIH 3T3 cells without DNase enzyme treatment.
- 7 May 2009
- Published by Wiley in Electrophoresis
- Vol. 30 (9) , 1538-1543
Acetic acid denaturing for RNA capillary polymer electrophoresis
A strong denaturant to cleave intramolecular hydrogen bonds in RNA is required for RNA size separation in a small sample volume (in vitro sample preparation before electrophoresis. The baseline separation of RNA with a size of 100–10 000 nt was achieved in 25 min by “in‐capillary denaturing polymer electrophoresis” with the running buffer containing 2.0 M acetic acid. The resolution and the theoretical plates of RNA separation peaks were larger than those of the RNA separation in a conventional CGE with in vitro sample preparation by 7.0 M urea. In addition, we detected RNA peaks from the nucleic acids extracted from NIH 3T3 cells without DNase enzyme treatment.
- 18 April 2008
- Published by Springer Nature in Chromatographia
- Vol. 67 (9) , 715-721
Hybridization Assay by Time-Resolved Capillary Gel Electrophoresis with a Lanthanide Chelate
- 18 April 2008
- Published by Springer Nature in Chromatographia
- Vol. 67 (9) , 715-721
Hybridization Assay by Time-Resolved Capillary Gel Electrophoresis with a Lanthanide Chelate
- 2 October 2007
- Published by Wiley in Journal of Polymer Science Part A: Polymer Chemistry
- Vol. 45 (22) , 5285-5295
Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content
A hybrid emulsion polymerization was formulated for synthesizing Fe3O4/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (≪critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe3O4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe3O4/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007
- 2 October 2007
- Published by Wiley in Journal of Polymer Science Part A: Polymer Chemistry
- Vol. 45 (22) , 5285-5295
Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content
A hybrid emulsion polymerization was formulated for synthesizing Fe3O4/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (≪critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe3O4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe3O4/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007