Norio Iwashita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Norio Iwashita has a total of 126 co-authors. Here are the top co-authors by number of shared publications:
Michio Inagaki
18 shared publicationsYoshihiro Sawada
Formerly, Osaka City University
13 shared publications- Kazuhiro Fujita
National Institute of Advanced Industrial Science and Technology
9 shared publications M. Inagaki
Faculty of Engineering, Hokkaido University, Kita-ku, Sapporo, Hokkaido 060, Japan
7 shared publicationsYoko Nishi
National Inst. of Advanced Industrial Sci. and Tech
6 shared publicationsAkira Yoshida
4 shared publications
Latest Publications
- 30 June 2024
- Published by The Carbon Society of Japan in TANSO
- Vol. 2024 (306) , 97-101
Revision of JIS R7651: “Measurement of Lattice Constants and Crystallite Sizes of Carbon Materials”
On February 20, 2024, a revised edition of the Japanese Industrial Standard JIS R7651 “Measurement of Lattice Constants and Crystallite Sizes of Carbon Materials” was issued. This document, reviews the standardization activity regarding this JIS revision from the establishment of the former GAKUSHIN-method in 1962 to the first establishment of JIS in July 2007, through to the survey of JIS in 2021 and to this revision of the JIS. The major point of the revision are discussed.
- 30 June 2024
- Published by The Carbon Society of Japan in TANSO
- Vol. 2024 (306) , 97-101
Revision of JIS R7651: “Measurement of Lattice Constants and Crystallite Sizes of Carbon Materials”
On February 20, 2024, a revised edition of the Japanese Industrial Standard JIS R7651 “Measurement of Lattice Constants and Crystallite Sizes of Carbon Materials” was issued. This document, reviews the standardization activity regarding this JIS revision from the establishment of the former GAKUSHIN-method in 1962 to the first establishment of JIS in July 2007, through to the survey of JIS in 2021 and to this revision of the JIS. The major point of the revision are discussed.
- 30 April 2024
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 33 (6) , 1278-1302
Assessment of the anisotropy development of mechanical properties of pitch-based carbon fibers
- 30 April 2024
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 33 (6) , 1278-1302
Assessment of the anisotropy development of mechanical properties of pitch-based carbon fibers
- 9 June 2021
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 31 (2) , 137-150
FEM analysis of flexural modulus of carbon fiber monofilament considering anisotropy
Carbon fibers are highly anisotropic materials and it is necessary to understand their mechanical properties in various directions as well as their axial tensile property, for accurate prediction of mechanical properties of carbon fiber reinforced plastics (CFRP). In this study, finite element method (FEM) analysis of three-point bending test of carbon fiber monofilament was carried out on two types of carbon fibers, PAN-based and high modulus pitch-based carbon fibers. The effect of anisotropy of mechanical properties of carbon fibers on flexural modulus was studied by investigating the span length dependence of the flexural modulus obtained by FEM analysis. The experimentally determined elastic parameters, longitudinal tensile, torsional, transverse, and axial compressive moduli, were used as the analysis parameters to consider the anisotropy of carbon fiber in this study. These analyzed results of the dependence of the flexural modulus on the span length showed good agreement with the experimental ones.
- 9 June 2021
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 31 (2) , 137-150
FEM analysis of flexural modulus of carbon fiber monofilament considering anisotropy
Carbon fibers are highly anisotropic materials and it is necessary to understand their mechanical properties in various directions as well as their axial tensile property, for accurate prediction of mechanical properties of carbon fiber reinforced plastics (CFRP). In this study, finite element method (FEM) analysis of three-point bending test of carbon fiber monofilament was carried out on two types of carbon fibers, PAN-based and high modulus pitch-based carbon fibers. The effect of anisotropy of mechanical properties of carbon fibers on flexural modulus was studied by investigating the span length dependence of the flexural modulus obtained by FEM analysis. The experimentally determined elastic parameters, longitudinal tensile, torsional, transverse, and axial compressive moduli, were used as the analysis parameters to consider the anisotropy of carbon fiber in this study. These analyzed results of the dependence of the flexural modulus on the span length showed good agreement with the experimental ones.
- 1 September 2019
- Published by The Carbon Society of Japan in TANSO
- Vol. 2019 (289) , 148-153
Temperature dependence of the coefficient of thermal expansion of different artificial graphites and the dimensional change during heat treatment of carbonized specimens
The linear thermal expansion of two artificial graphite products, an isotropic graphite and an extruded nipple electrode, was measured during heating up to 2400 °C by a newly developed device with a non-contact laser micro-gage. The temperature dependence of the coefficient of thermal expansion (CTE) of two graphites was investigated. The test piece was 100 mm long a round rod of 20 mm diameter, which is large enough to reflect the different textures of these products. In the nipple electrode, two specimens taken from parallel or perpendicular to the extrusion direction were used. For the isotropic graphite and the parallel specimen of the nipple electrode, temperature dependences of the CTE below 500 °C were different. In the case of the parallel nipple specimen, a negative value of CTE was found in the temperature region from 150 to 400 °C, probably reflecting the negative CTE along the basal planes of a graphite crystal. In situ measurement of the dimensional changes of the specimens before graphitization process of these products during heat treatment up to 2400 °C was also attempted. For the isotropic product, two-step of thermal shrinkage was observed, but for the nipple electrode, growth above 1400 °C was clearly observed, resulting from the “puffing” of calcined needle cokes. For the puffing, it was found that there was clear anisotropy in the extruded direction of the nipple electrode.
- 1 September 2019
- Published by The Carbon Society of Japan in TANSO
- Vol. 2019 (289) , 148-153
Temperature dependence of the coefficient of thermal expansion of different artificial graphites and the dimensional change during heat treatment of carbonized specimens
The linear thermal expansion of two artificial graphite products, an isotropic graphite and an extruded nipple electrode, was measured during heating up to 2400 °C by a newly developed device with a non-contact laser micro-gage. The temperature dependence of the coefficient of thermal expansion (CTE) of two graphites was investigated. The test piece was 100 mm long a round rod of 20 mm diameter, which is large enough to reflect the different textures of these products. In the nipple electrode, two specimens taken from parallel or perpendicular to the extrusion direction were used. For the isotropic graphite and the parallel specimen of the nipple electrode, temperature dependences of the CTE below 500 °C were different. In the case of the parallel nipple specimen, a negative value of CTE was found in the temperature region from 150 to 400 °C, probably reflecting the negative CTE along the basal planes of a graphite crystal. In situ measurement of the dimensional changes of the specimens before graphitization process of these products during heat treatment up to 2400 °C was also attempted. For the isotropic product, two-step of thermal shrinkage was observed, but for the nipple electrode, growth above 1400 °C was clearly observed, resulting from the “puffing” of calcined needle cokes. For the puffing, it was found that there was clear anisotropy in the extruded direction of the nipple electrode.
- 15 June 2019
- Published by The Carbon Society of Japan in TANSO
- Vol. 2019 (288) , 91-102
Development of high temperature property measurements for artificial graphite materials and their analysis
- 15 June 2019
- Published by The Carbon Society of Japan in TANSO
- Vol. 2019 (288) , 91-102
Development of high temperature property measurements for artificial graphite materials and their analysis
- 15 May 2017
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 66 (5) , 348-354
Effect of Pre-Loading on Tensile Strength of Carbon Fiber
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- 15 May 2017
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 66 (5) , 348-354
Effect of Pre-Loading on Tensile Strength of Carbon Fiber
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- Open Access
- 1 January 2017
- Published by The Carbon Society of Japan in TANSO
- Vol. 2017 (278) , 111-117
Measurement of the distribution of cross sectional shape along the axis of carbon fibers and its effect on the mechanical properties
Mechanical tests of a single carbon fiber are difficult because of its small size. The diameter or the shape of the cross section is very important for a precise evaluation of the properties. However, most size evaluations use a measurement of fiber diameter in only one direction and its effect on the results has not been studied sufficiently. In order to investigate the apparent diameter variation of carbon fibers, we have developed a new apparatus with two functions. One is that we can accurately control the measurement position along the fiber axis and the other is that we can rotate a single fiber around its axis. Measurements were carried out for two types of carbon fibers. Though the cross section of one of them was far from circular, its shape was almost the same along the fiber axis and its orientation was rotating randomly. For both fibers, an assumption of an elliptical cross section gave a smaller coefficient of variation for torsional modulus and tensile properties.
- 1 January 2017
- Published by The Carbon Society of Japan in TANSO
- Vol. 2017 (278) , 111-117
Open AccessMeasurement of the distribution of cross sectional shape along the axis of carbon fibers and its effect on the mechanical properties
Mechanical tests of a single carbon fiber are difficult because of its small size. The diameter or the shape of the cross section is very important for a precise evaluation of the properties. However, most size evaluations use a measurement of fiber diameter in only one direction and its effect on the results has not been studied sufficiently. In order to investigate the apparent diameter variation of carbon fibers, we have developed a new apparatus with two functions. One is that we can accurately control the measurement position along the fiber axis and the other is that we can rotate a single fiber around its axis. Measurements were carried out for two types of carbon fibers. Though the cross section of one of them was far from circular, its shape was almost the same along the fiber axis and its orientation was rotating randomly. For both fibers, an assumption of an elliptical cross section gave a smaller coefficient of variation for torsional modulus and tensile properties.
- 15 August 2016
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 65 (8) , 573-579
Evaluation of Torsional-Tensile Properties of Carbon Fiber
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- 15 August 2016
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 65 (8) , 573-579
Evaluation of Torsional-Tensile Properties of Carbon Fiber
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- Open Access
- 1 July 2015
- Published by Elsevier in Sustainable Materials and Technologies
- Vol. 4, 18-23
Activated carbon production by co-carbonization of feathers using water-soluble phenolic resin under controlled graphitization
- 1 July 2015
- Published by Elsevier in Sustainable Materials and Technologies
- Vol. 4, 18-23
Open AccessActivated carbon production by co-carbonization of feathers using water-soluble phenolic resin under controlled graphitization