Federico París
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Federico París has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Vladislav Mantic
Grupo de Elasticidad y Resistencia de Materiales, Escuela Técnica Superior de Ingeniería, Universidad de Sevilla, Camino de los Descubrimientos s/n, 41092 Sevilla, Spain
5 shared publications - Enrique Graciani
Universidad de Sevilla
2 shared publications - Alberto Barroso
School of Engineering, University of Seville, Seville, Spain
1 shared publication - Elena Correa
Group of Elasticity and Strength of Materials, Department of Continuum Mechanics and Theory of Structures, School of Engineering, Universidad de Sevilla, 41092 Seville Spain
1 shared publication - J.E. Ortiz
School of Engineering, University of Seville
1 shared publication - L. J. Gray
Oak Ridge Natl Lab, Comp Sci & Math Div, Oak Ridge, TN 37831 USA
1 shared publication
Latest Publications
- 1 October 2012
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 36 (10) , 1502-1512
A Galerkin projection technique for the evaluation of potential derivatives on a smooth boundary in 2D BEM
- 1 October 2012
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 36 (10) , 1502-1512
A Galerkin projection technique for the evaluation of potential derivatives on a smooth boundary in 2D BEM
- Open Access
- 9 January 2012
- Published by Rutgers University Libraries in Electronic Journal of Boundary Elements
- Vol. 10 (1)
Recent developments in the evaluation of the 3D fundamental solution and its derivatives for transversely isotropic elastic materials
Recent developments in the evaluation of the 3D fundamental solution and its derivatives for transversely isotropic elastic materials
- 9 January 2012
- Published by Rutgers University Libraries in Electronic Journal of Boundary Elements
- Vol. 10 (1)
Open AccessRecent developments in the evaluation of the 3D fundamental solution and its derivatives for transversely isotropic elastic materials
Recent developments in the evaluation of the 3D fundamental solution and its derivatives for transversely isotropic elastic materials
- 1 February 2007
- Published by Springer Nature in International Journal of Fracture
- Vol. 143 (3) , 287-290
On the estimation of the first interpenetration point in the open model of interface cracks
- 1 February 2007
- Published by Springer Nature in International Journal of Fracture
- Vol. 143 (3) , 287-290
On the estimation of the first interpenetration point in the open model of interface cracks
- 27 September 2006
- Published by Wiley in Journal of Applied Mechanics
- Vol. 74 (4) , 703-716
Kinking of Transversal Interface Cracks Between Fiber and Matrix
Under loads normal to the direction of the fibers, composites suffer failures that are known as matrix or interfiber failures, typically involving interface cracks between matrix and fibers, the coalescence of which originates macrocracks in the composite. The purpose of this paper is to develop a micromechanical model, using the boundary element method, to generate information aiming to explain and support the mechanism of appearance and propagation of the damage. To this end, a single fiber surrounded by the matrix and with a partial debonding is studied. It has been found that under uniaxial loading transversal to the fibers direction the most significant phenomena appear for semidebonding angles in the interval between 60deg and 70deg. After this interval the growth of the crack along the interface is stable (energy release rate (ERR) decreasing) in pure Mode II, whereas it is plausibly unstable in mixed mode (dominated by Mode I for semidebondings smaller than 30deg) until it reaches the interval. At this interval the direction of maximum circumferential stress at the neighborhood of the crack tip is approximately normal to the applied load. If a crack corresponding to a debonding in this interval leaves the interface and penetrates into the matrix then: (a) the growth through the matrix is unstable in pure Mode I; (b) the value of the ERR reaches a maximum (in comparison with other debonding angles); and (c) the ERR is greater than that released if the crack continued growing along the interface. All this suggests that it is in this interval of semidebondings (60-70deg) that conditions are most appropriate for an interface crack to kink. Experiments developed by the authors show an excellent agreement between the predictions generated in this paper and the evolution of the damage in an actual composite.
- 27 September 2006
- Published by Wiley in Journal of Applied Mechanics
- Vol. 74 (4) , 703-716
Kinking of Transversal Interface Cracks Between Fiber and Matrix
Under loads normal to the direction of the fibers, composites suffer failures that are known as matrix or interfiber failures, typically involving interface cracks between matrix and fibers, the coalescence of which originates macrocracks in the composite. The purpose of this paper is to develop a micromechanical model, using the boundary element method, to generate information aiming to explain and support the mechanism of appearance and propagation of the damage. To this end, a single fiber surrounded by the matrix and with a partial debonding is studied. It has been found that under uniaxial loading transversal to the fibers direction the most significant phenomena appear for semidebonding angles in the interval between 60deg and 70deg. After this interval the growth of the crack along the interface is stable (energy release rate (ERR) decreasing) in pure Mode II, whereas it is plausibly unstable in mixed mode (dominated by Mode I for semidebondings smaller than 30deg) until it reaches the interval. At this interval the direction of maximum circumferential stress at the neighborhood of the crack tip is approximately normal to the applied load. If a crack corresponding to a debonding in this interval leaves the interface and penetrates into the matrix then: (a) the growth through the matrix is unstable in pure Mode I; (b) the value of the ERR reaches a maximum (in comparison with other debonding angles); and (c) the ERR is greater than that released if the crack continued growing along the interface. All this suggests that it is in this interval of semidebondings (60-70deg) that conditions are most appropriate for an interface crack to kink. Experiments developed by the authors show an excellent agreement between the predictions generated in this paper and the evolution of the damage in an actual composite.
- 18 June 2006
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 66 (12) , 1884-1912
On the removal of the non-uniqueness in the solution of elastostatic problems by symmetric Galerkin BEM
- 18 June 2006
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 66 (12) , 1884-1912
On the removal of the non-uniqueness in the solution of elastostatic problems by symmetric Galerkin BEM