T. X. Mei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
T. X. Mei has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Roger M. Goodall
School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough, UK
3 shared publications H. Li
School of Electronic and Electrical Engineering, University of Leeds, Leeds LS2 9JT, United Kingdom
2 shared publicationsX.J. Ding
School of Electronic and Electrical Engineering , The University of Leeds , Leeds, UK
2 shared publicationsA.H. Wickens
1 shared publicationC. Kossmann
Bombardier Transportation, Winterthur, Switzerland
1 shared publicationD A Wilson
1 shared publication
Latest Publications
- 1 September 2008
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 46 (sup1) , 277-287
A model-less technique for the fault detection of rail vehicle suspensions
This paper presents a novel method for the fault detection and condition monitoring of rail vehicle suspensions. The proposed technique takes advantage of the vehicle (suspension) configurations that are often symmetrical, and explores the additional dynamic interactions between different motions of a bogie or body caused by the failure of suspension components. The basic principle of the proposed detection method is presented and the interactions due to suspension fault conditions are analysed using a conventional two-axle bogie. Side-view models of a bogie vehicle are used in the study to demonstrate the effectiveness of the novel method in detecting damper faults in the suspensions. Both linear and bi-linear dampers are studied.
- 1 September 2008
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 46 (sup1) , 277-287
A model-less technique for the fault detection of rail vehicle suspensions
This paper presents a novel method for the fault detection and condition monitoring of rail vehicle suspensions. The proposed technique takes advantage of the vehicle (suspension) configurations that are often symmetrical, and explores the additional dynamic interactions between different motions of a bogie or body caused by the failure of suspension components. The basic principle of the proposed detection method is presented and the interactions due to suspension fault conditions are analysed using a conventional two-axle bogie. Side-view models of a bogie vehicle are used in the study to demonstrate the effectiveness of the novel method in detecting damper faults in the suspensions. Both linear and bi-linear dampers are studied.
- 1 January 2008
- Published by Institution of Engineering and Technology (IET)
- p. 39
New condition monitoring techniques for vehicle suspensions
This paper presents two simple and potentially powerful approaches for the condition monitoring of rail vehicle suspensions, which explore the relative changes between different dynamic motions caused by suspension faults. Damper failures in vertical (primary) suspensions of a conventional bogie are detected based on the measurements of the bounce, pitch and roll accelerations of the bogie frame. The effectiveness of the proposed fault detection methods is demonstrated. (6 pages)
- 1 January 2008
- Published by Institution of Engineering and Technology (IET)
- p. 39
New condition monitoring techniques for vehicle suspensions
This paper presents two simple and potentially powerful approaches for the condition monitoring of rail vehicle suspensions, which explore the relative changes between different dynamic motions caused by suspension faults. Damper failures in vertical (primary) suspensions of a conventional bogie are detected based on the measurements of the bounce, pitch and roll accelerations of the bogie frame. The effectiveness of the proposed fault detection methods is demonstrated. (6 pages)
- 1 January 2008
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 41 (2) , 8275-8280
A Mechatronic Approach for Anti-slip Control in Railway Traction
- 1 January 2008
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 41 (2) , 8275-8280
A Mechatronic Approach for Anti-slip Control in Railway Traction
- 5 December 2007
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 130 (1) , 011002
Control Design for the Active Stabilization of Rail Wheelsets
Through a detailed control assessment of a conventional railway wheelset, this paper addresses some of the key design issues in the development of active primary suspensions for the stabilization control of railway vehicles. It reveals the basic feedback requirements for achieving adequate stability and hence provides a useful insight of how active controllers may be structured. For the control design, a number of factors in addition to the stabilization are considered including the actuation requirements, creep forces at the wheel-rail contact, track following as well as robustness against parameter variations. Based on the outcome of the control analysis, the study proposes a design and optimization procedure for the development of active wheelset control. The design method is applied to a two-axle vehicle in a case study, which shows that the new design approach is advantageous when compared with other design methods previously studied.
- 5 December 2007
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 130 (1) , 011002
Control Design for the Active Stabilization of Rail Wheelsets
Through a detailed control assessment of a conventional railway wheelset, this paper addresses some of the key design issues in the development of active primary suspensions for the stabilization control of railway vehicles. It reveals the basic feedback requirements for achieving adequate stability and hence provides a useful insight of how active controllers may be structured. For the control design, a number of factors in addition to the stabilization are considered including the actuation requirements, creep forces at the wheel-rail contact, track following as well as robustness against parameter variations. Based on the outcome of the control analysis, the study proposes a design and optimization procedure for the development of active wheelset control. The design method is applied to a two-axle vehicle in a case study, which shows that the new design approach is advantageous when compared with other design methods previously studied.
- 1 January 2006
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 44 (sup1) , 83-92
Stability control of railway bogies using absolute stiffness: sky-hook spring approach
This paper presents a novel control method for the stabilization of railway bogies using a strategy based on the concept of an absolute stiffness, in which the control effort is proportional to the yaw movement of the wheelset alone. The idea can be considered as if a spring is connected between the sky and a wheelset, hence termed a ‘sky-hook spring’. In this paper, the effectiveness of the control strategy is studied in detail and compared with other control solutions. It is shown that the new approach offers a number of advantages: it provides a robust control solution for the stability of railway wheelsets and there is no need for the measurement of bogie motions or the use of secondary yaw dampers. Sensing requirement can be readily met and control design is relatively simple.
- 1 January 2006
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 44 (sup1) , 83-92
Stability control of railway bogies using absolute stiffness: sky-hook spring approach
This paper presents a novel control method for the stabilization of railway bogies using a strategy based on the concept of an absolute stiffness, in which the control effort is proportional to the yaw movement of the wheelset alone. The idea can be considered as if a spring is connected between the sky and a wheelset, hence termed a ‘sky-hook spring’. In this paper, the effectiveness of the control strategy is studied in detail and compared with other control solutions. It is shown that the new approach offers a number of advantages: it provides a robust control solution for the stability of railway wheelsets and there is no need for the measurement of bogie motions or the use of secondary yaw dampers. Sensing requirement can be readily met and control design is relatively simple.
- 1 January 2005
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 38 (1) , 256-261
FPGA BASED REAL TIME SIMULATION FOR ELECTRICAL MACHINES
- 1 January 2005
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 38 (1) , 256-261
FPGA BASED REAL TIME SIMULATION FOR ELECTRICAL MACHINES
- 1 March 2001
- Published by SAGE Publications in Transactions of the Institute of Measurement and Control
- Vol. 23 (3) , 163-181
Kalman filters applied to actively controlled railway vehicle suspensions
- 1 March 2001
- Published by SAGE Publications in Transactions of the Institute of Measurement and Control
- Vol. 23 (3) , 163-181
Kalman filters applied to actively controlled railway vehicle suspensions
- 1 September 2000
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 33 (26) , 265-270
Mechatronic Solutions for High Speed Railway Vehicles
- 1 September 2000
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 33 (26) , 265-270
Mechatronic Solutions for High Speed Railway Vehicles