Rafael Reif
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rafael Reif has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
A. Fan
Microsystem Technology Laboratories Massachusetts Institute of Technology 02139 Cambridge Massachusetts USA
1 shared publicationA. Rahman
Microsystem Technology Laboratories Massachusetts Institute of Technology 02139 Cambridge Massachusetts USA
1 shared publication- Anantha P. Chandrakasan
Massachusetts Institute of Technology
1 shared publication - Andy Fan
MIT, Cambridge, MA, 02139, United States
1 shared publication - Chuan Seng Tan
Nanyang Technological University, EEE/Microelectronics, 50 Nanyang Avenue, S2-B2c-127, Singapore 639798, Singapore, 639798, Singapore, 65-6790-5636
1 shared publication - Kuan-Neng Chen
National yang Ming Chiao Tung University
1 shared publication
Latest Publications
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 970
Silicon Layer Stacking Enabled by Wafer Bonding
Three-dimensional integrated circuits (3-D ICs), in the form of a vertical stack of several interconnected device layers, have many performance, form factor, and integration advantages. The main objective of this work is to develop reliable process technology to enable the fabrication of a vertically interconnected silicon multi-layer stack.Low temperature wafer bonding processes, both copper thermo-compression bonding and silicon dioxide fusion bonding, are studied extensively as key enabling technology. Cu thermo-compression bonding is studied for its feasibility as a permanent bond between active layers in a multi-layer stack. Silicon dioxide wafer bonding, on the other hand, is used as a temporary bond to attach a donor wafer to a handle wafer during donor wafer thinning and subsequent layer transfer. Sufficiently high bond strength is obtained with careful surface preparation and activation prior to bonding.Silicon layer can be stacked either in a “face down” or “face up” orientation. Using a combination of wafer bonding and thinning, double-layer stacks in both orientations are fabricated. By repeating these steps on two “face down” double-layer stacks, a four-layer stack is successful demonstrated.
- 1 January 2006
- Published by Springer Nature in MRS Proceedings
- Vol. 970
Silicon Layer Stacking Enabled by Wafer Bonding
Three-dimensional integrated circuits (3-D ICs), in the form of a vertical stack of several interconnected device layers, have many performance, form factor, and integration advantages. The main objective of this work is to develop reliable process technology to enable the fabrication of a vertically interconnected silicon multi-layer stack.Low temperature wafer bonding processes, both copper thermo-compression bonding and silicon dioxide fusion bonding, are studied extensively as key enabling technology. Cu thermo-compression bonding is studied for its feasibility as a permanent bond between active layers in a multi-layer stack. Silicon dioxide wafer bonding, on the other hand, is used as a temporary bond to attach a donor wafer to a handle wafer during donor wafer thinning and subsequent layer transfer. Sufficiently high bond strength is obtained with careful surface preparation and activation prior to bonding.Silicon layer can be stacked either in a “face down” or “face up” orientation. Using a combination of wafer bonding and thinning, double-layer stacks in both orientations are fabricated. By repeating these steps on two “face down” double-layer stacks, a four-layer stack is successful demonstrated.
- Open Access
- 1 January 1999
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 2 (10) , 534-536
Copper Wafer Bonding
Silicon wafers, coated with nm evaporated copper, were successfully bonded at for with a postbonding anneal in for . The postbonding anneal was required for successful bonding, but the annealing temperature did not influence the bond strength from 400 to . The inclusion of a tantalum diffusion barrier for did not affect the bonding strength or the bonding temperature. ©1999 The Electrochemical Society
- 1 January 1999
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 2 (10) , 534-536
Open AccessCopper Wafer Bonding
Silicon wafers, coated with nm evaporated copper, were successfully bonded at for with a postbonding anneal in for . The postbonding anneal was required for successful bonding, but the annealing temperature did not influence the bond strength from 400 to . The inclusion of a tantalum diffusion barrier for did not affect the bonding strength or the bonding temperature. ©1999 The Electrochemical Society