Farzad Mohajeri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Farzad Mohajeri has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Seyed Ali Razavi Parizi
School of Electrical and Computer Engineering, Graduate University of Advanced Technology, Kerman, Iran
4 shared publicationsMohammad Mohammadpour
Department of Communications and Electronics School of Electrical and Computer Engineering Shiraz University Shiraz Fars Iran
3 shared publications- Masoud Movahhedi
Electrical Engineering Department, Yazd University, Yazd, Iran
2 shared publications - Mehdi Hamidkhani
Islamic Azad University, Isfahan, Iran
2 shared publications - Mohammad Mohammadpour
School of Electrical and Computer Engineering, Shiraz University, Shiraz, Iran
2 shared publications - Sheyda Shams
School of Electrical and Computer Engineering, Shiraz University, Shiraz, Iran
2 shared publications
Latest Publications
- Open Access
- 29 November 2025
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
A high efficiency slot array antenna with single layered gap waveguide feeding system for long-range wireless systems
This paper presents a slot array antenna composed of H-plane horns as radiating slots and a pillbox feeding mechanism in gap waveguide (GW) technology. This new configuration presents a new full-metal slot array antenna with low complexity, fabrication cost, and high gain with directive radiation, which can make it a good candidate for use in long-range wireless systems. Making use of an H-plane reflector in the feeding part of the antenna has removed the need for a corporate feed network and enhanced the structure’s simplicity. Moreover, the use of semi-horn-shaped radiating slots has improved the antenna efficiency by resolving the grating lobe issue associated with transverse slots. These features make the proposed antenna easily scalable for higher gains without imposing extra complexity on the design and fabrication process. The GW technology also lets the proposed antenna be a promising solution for the next-generation millimeter-wave systems. In addition, the proposed fully metallic antenna leverages a design that offers high efficiency and a flat gain response over the desired bandwidth. A fabricated prototype exhibits 60–90% overall efficiency over an impedance bandwidth of about 8% (\(\:{S}_{11}\) < -10 dB), and a 2.5 dB gain variation across the operating bandwidth.- 29 November 2025
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessA high efficiency slot array antenna with single layered gap waveguide feeding system for long-range wireless systems
This paper presents a slot array antenna composed of H-plane horns as radiating slots and a pillbox feeding mechanism in gap waveguide (GW) technology. This new configuration presents a new full-metal slot array antenna with low complexity, fabrication cost, and high gain with directive radiation, which can make it a good candidate for use in long-range wireless systems. Making use of an H-plane reflector in the feeding part of the antenna has removed the need for a corporate feed network and enhanced the structure’s simplicity. Moreover, the use of semi-horn-shaped radiating slots has improved the antenna efficiency by resolving the grating lobe issue associated with transverse slots. These features make the proposed antenna easily scalable for higher gains without imposing extra complexity on the design and fabrication process. The GW technology also lets the proposed antenna be a promising solution for the next-generation millimeter-wave systems. In addition, the proposed fully metallic antenna leverages a design that offers high efficiency and a flat gain response over the desired bandwidth. A fabricated prototype exhibits 60–90% overall efficiency over an impedance bandwidth of about 8% (\(\:{S}_{11}\) < -10 dB), and a 2.5 dB gain variation across the operating bandwidth. - Open Access
- 7 August 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-13
H-plane gap-RGW horn antenna with very low side lobe level
This paper presents and applies a new concept of gap-RGW to develop a new configuration for RGW H-plane horn antennas. The proposed antenna is fully metallic and can generate a very low side-lobe level along with a flat gain response over a reasonable bandwidth, which is one of the advantages of this antenna. A prototype of the presented structure is designed and fabricated which provides the impedance bandwidth (S11 < − 10 dB) of about 25% with SLL < − 20 dB and 2 dB gain variation over the operating bandwidth.
- 7 August 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-13
Open AccessH-plane gap-RGW horn antenna with very low side lobe level
This paper presents and applies a new concept of gap-RGW to develop a new configuration for RGW H-plane horn antennas. The proposed antenna is fully metallic and can generate a very low side-lobe level along with a flat gain response over a reasonable bandwidth, which is one of the advantages of this antenna. A prototype of the presented structure is designed and fabricated which provides the impedance bandwidth (S11 < − 10 dB) of about 25% with SLL < − 20 dB and 2 dB gain variation over the operating bandwidth.
- 23 May 2023
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Electrical Engineering
- Vol. 47 (3) , 1251-1263
Design and Implementation of a High-Efficiency 45 W Compact Class-J Power Amplifier Based on a Simplified Real Frequency Technique for n77 5G New Radio Applications
- 23 May 2023
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Electrical Engineering
- Vol. 47 (3) , 1251-1263
Design and Implementation of a High-Efficiency 45 W Compact Class-J Power Amplifier Based on a Simplified Real Frequency Technique for n77 5G New Radio Applications
- 7 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (7) , 1612-1616
Time-Domain Meshless Method Simulation of Metasurfaces With Generalized Sheet Transition Conditions
This paper presents a new time-domain formulation of a meshless method based on the generalized sheet transition conditions (GSTCs). This formulation is applicable for modeling a kind of dispersive metasurface and a time-varying metasurface. This is the first time a meshless method is developed for analysis of the metasurfaces using GSTCs. The significance of time-domain meshless methods originates from their capabilities for multi-scale and conformal modeling in addition to analysis of problems in a broad frequency-range. Here, for simplicity, the meshless formulation is presented for analysis of 1-D problems consisting of monoisotropic metasurfaces. The extension of this method to 2-D and 3-D problems or bianisotropic metasurfaces is straightforward. The scheme is verified by numerical examples.
- 7 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (7) , 1612-1616
Time-Domain Meshless Method Simulation of Metasurfaces With Generalized Sheet Transition Conditions
This paper presents a new time-domain formulation of a meshless method based on the generalized sheet transition conditions (GSTCs). This formulation is applicable for modeling a kind of dispersive metasurface and a time-varying metasurface. This is the first time a meshless method is developed for analysis of the metasurfaces using GSTCs. The significance of time-domain meshless methods originates from their capabilities for multi-scale and conformal modeling in addition to analysis of problems in a broad frequency-range. Here, for simplicity, the meshless formulation is presented for analysis of 1-D problems consisting of monoisotropic metasurfaces. The extension of this method to 2-D and 3-D problems or bianisotropic metasurfaces is straightforward. The scheme is verified by numerical examples.
- 1 December 2022
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Electrical Engineering
- Vol. 47 (2) , 411-419
An SWB MIMO Antenna with Dual Band Rejection and Polarization Diversity for Ultra-Wide Band Applications
- 1 December 2022
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Electrical Engineering
- Vol. 47 (2) , 411-419
An SWB MIMO Antenna with Dual Band Rejection and Polarization Diversity for Ultra-Wide Band Applications
- 29 November 2022
- Published by American Geophysical Union (AGU) in Radio Science
- Vol. 57 (12)
Feature Enhancement of Three Log‐Periodic Antennas Based on Antipodal Vivaldi Patch
Today, microstrip antennas have received a lot of attention due to their unique features such as low weight and volume, easy and cheap construction, and the ability to adapt to planar structures. Of course, the important problem with these antennas is their small gain and bandwidth. In this paper, the gain and bandwidth of the microstrip antenna with a patch in the form of Antipodal Vivaldi are improved by using log‐periodic structures. Three 8‐element log‐periodic structures designed in a straight‐line, U‐shaped and V‐shaped are proposed, simulated and fabricated. The dimensions of these antennas are , and respectively. The results of the measurements show that the bandwidth of the 8‐element straight‐line, U‐shaped and V‐shaped antennas are 3–18, 2.6–18, and 2.4–18 GHz respectively, and their maximum gain are 6.26, 8.3, and 7.61 dBi, respectively, which has increased the bandwidth by approximately 125% compared to the single element mode and increased the gain from 2.26 to 4.3 dBi. These quantities show that among the three antennas proposed in this article, the V‐shaped antenna has the highest bandwidth (15.6 GHz) and the U‐shaped antenna has the highest maximum gain (8.3 dBi). Of course, it is possible to achieve more gain by changing the angle between the branches of the V‐shaped antenna, but it may ruin the bandwidth.
- 29 November 2022
- Published by American Geophysical Union (AGU) in Radio Science
- Vol. 57 (12)
Feature Enhancement of Three Log‐Periodic Antennas Based on Antipodal Vivaldi Patch
Today, microstrip antennas have received a lot of attention due to their unique features such as low weight and volume, easy and cheap construction, and the ability to adapt to planar structures. Of course, the important problem with these antennas is their small gain and bandwidth. In this paper, the gain and bandwidth of the microstrip antenna with a patch in the form of Antipodal Vivaldi are improved by using log‐periodic structures. Three 8‐element log‐periodic structures designed in a straight‐line, U‐shaped and V‐shaped are proposed, simulated and fabricated. The dimensions of these antennas are , and respectively. The results of the measurements show that the bandwidth of the 8‐element straight‐line, U‐shaped and V‐shaped antennas are 3–18, 2.6–18, and 2.4–18 GHz respectively, and their maximum gain are 6.26, 8.3, and 7.61 dBi, respectively, which has increased the bandwidth by approximately 125% compared to the single element mode and increased the gain from 2.26 to 4.3 dBi. These quantities show that among the three antennas proposed in this article, the V‐shaped antenna has the highest bandwidth (15.6 GHz) and the U‐shaped antenna has the highest maximum gain (8.3 dBi). Of course, it is possible to achieve more gain by changing the angle between the branches of the V‐shaped antenna, but it may ruin the bandwidth.
- 24 August 2022
- Published by Taylor & Francis in Australian Journal of Electrical and Electronics Engineering
- Vol. 20 (1) , 85-94
Using of metasurface lens and particle swarm optimisation for enhancement of parameters of a pyramidal horn antenna
In this article, a lens is applied to reduce the horn antenna’s Side Lobe Level (SLL) based on controlling the phase and amplitude distribution of the electromagnetic fields over the aperture of the horn antenna in the X band (8−12 GHz) for radar applications. By locating the metasurface lens inside the standard X band pyramidal horn, the SLL is decreased by 4–15 dB in E-plane and 0.8–7 dB in H-plane. The measured results with metasurface lenses demonstrate the reduction of SLL over the entire bandwidth. Good agreement between measurement and simulation results shows the tapering of field distribution over the aperture of the horn antenna.
- 24 August 2022
- Published by Taylor & Francis in Australian Journal of Electrical and Electronics Engineering
- Vol. 20 (1) , 85-94
Using of metasurface lens and particle swarm optimisation for enhancement of parameters of a pyramidal horn antenna
In this article, a lens is applied to reduce the horn antenna’s Side Lobe Level (SLL) based on controlling the phase and amplitude distribution of the electromagnetic fields over the aperture of the horn antenna in the X band (8−12 GHz) for radar applications. By locating the metasurface lens inside the standard X band pyramidal horn, the SLL is decreased by 4–15 dB in E-plane and 0.8–7 dB in H-plane. The measured results with metasurface lenses demonstrate the reduction of SLL over the entire bandwidth. Good agreement between measurement and simulation results shows the tapering of field distribution over the aperture of the horn antenna.
- 16 May 2022
- Published by Brno University of Technology in Radioengineering
- Vol. 31 (2) , 193-200
Gain and Bandwidth Enhancement of a Metamaterial Loaded Antipodal Vivaldi Antenna Fed by Substrate Integrated Waveguide
- 16 May 2022
- Published by Brno University of Technology in Radioengineering
- Vol. 31 (2) , 193-200
Gain and Bandwidth Enhancement of a Metamaterial Loaded Antipodal Vivaldi Antenna Fed by Substrate Integrated Waveguide
- 18 April 2022
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 77 (1-2) , 77-85
Gain enhancement of a SIW H-plane horn antenna using of metamaterial array
In this paper, a novel, compact and high gain H-plane horn antenna with Substrate Integrated Waveguide (SIW) technology is examined for X-band applications. To increase the gain, an array of metamaterials is used by cutting the gap in the aperture area of the antenna in high metallization. After examining the size and position of the metamaterial unit cell and several array elements, which act as a focusing structure, and in addition, by reducing the electric permittivity coefficient of the substrate and consequently reducing the losses, an increase in gain is achieved. The performance of the proposed SIW horn antenna with metamaterials has been compared with the SIW conventional horn antenna without metamaterials. To highlight this point, the proposed antenna was designed with CST software. Then, it was fabricated and measured. Measurements show that the gain of the modified antenna is 9.2 dBi, which is 6.2 dBi higher than a conventional antenna.
- 18 April 2022
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 77 (1-2) , 77-85
Gain enhancement of a SIW H-plane horn antenna using of metamaterial array
In this paper, a novel, compact and high gain H-plane horn antenna with Substrate Integrated Waveguide (SIW) technology is examined for X-band applications. To increase the gain, an array of metamaterials is used by cutting the gap in the aperture area of the antenna in high metallization. After examining the size and position of the metamaterial unit cell and several array elements, which act as a focusing structure, and in addition, by reducing the electric permittivity coefficient of the substrate and consequently reducing the losses, an increase in gain is achieved. The performance of the proposed SIW horn antenna with metamaterials has been compared with the SIW conventional horn antenna without metamaterials. To highlight this point, the proposed antenna was designed with CST software. Then, it was fabricated and measured. Measurements show that the gain of the modified antenna is 9.2 dBi, which is 6.2 dBi higher than a conventional antenna.
- 7 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (8) , 7328-7333
A Dispersive Formulation of Time-Domain Meshless Method With PML Absorbing Boundary Condition for Analysis of Left-Handed Materials
We have proposed a dispersive formulation of scalar-based meshless method for time-domain analysis of electromagnetic wave propagation through left-handed (LH) materials. Moreover, we have incorporated Berenger’s perfectly matched layer (PML) absorbing boundary condition (ABC) into the dispersive formulation to truncate open-domain structures. In general, the dispersive formulations of conventional numerical methods are proper tools for analysis of LH media, whenever the LH media can be characterized by considering spatial or frequency dispersion effect for the constitutive parameters. In comparison to the grid-based numerical methods, it is proved that meshless methods not only are strong tools for accurate approximation of derivatives in Maxwell’s equations but also can provide more flexibility in modeling the spatial domain of problems. However, we have not seen any reports on using dispersive forms of meshless methods for simulation of wave propagation in metamaterials and applying any PML ABCs to dispersive formulation of meshless method. The proposed formulation enables us to take advantage of meshless methods in analysis of LH media with frequency-dependent parameters. For modeling the frequency behavior of the medium, we have used auxiliary differential equation (ADE) method based on the relations between electromagnetic fields intensities and current densities. Effectiveness of the proposed formulation is verified by analysis of 2D and 3D numerical examples; also, some basic factors which affect the accuracy, stability, and computational cost of the simulations are studied.
- 7 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 70 (8) , 7328-7333
A Dispersive Formulation of Time-Domain Meshless Method With PML Absorbing Boundary Condition for Analysis of Left-Handed Materials
We have proposed a dispersive formulation of scalar-based meshless method for time-domain analysis of electromagnetic wave propagation through left-handed (LH) materials. Moreover, we have incorporated Berenger’s perfectly matched layer (PML) absorbing boundary condition (ABC) into the dispersive formulation to truncate open-domain structures. In general, the dispersive formulations of conventional numerical methods are proper tools for analysis of LH media, whenever the LH media can be characterized by considering spatial or frequency dispersion effect for the constitutive parameters. In comparison to the grid-based numerical methods, it is proved that meshless methods not only are strong tools for accurate approximation of derivatives in Maxwell’s equations but also can provide more flexibility in modeling the spatial domain of problems. However, we have not seen any reports on using dispersive forms of meshless methods for simulation of wave propagation in metamaterials and applying any PML ABCs to dispersive formulation of meshless method. The proposed formulation enables us to take advantage of meshless methods in analysis of LH media with frequency-dependent parameters. For modeling the frequency behavior of the medium, we have used auxiliary differential equation (ADE) method based on the relations between electromagnetic fields intensities and current densities. Effectiveness of the proposed formulation is verified by analysis of 2D and 3D numerical examples; also, some basic factors which affect the accuracy, stability, and computational cost of the simulations are studied.