GLGilbert Lebrun

Gilbert Lebrun

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Gilbert Lebrun has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Tensile properties improvement of a unidirectional-mat flax/epoxy composite via click chemistry, nanocellulose addition and surface refining of short mat fibres

    by Abdelhadi Blal, Gilbert Lebrun, François Brouillette, Éric Loranger

    The mechanical characteristics of natural fibre composites (NFCs) are closely linked to fibre-matrix and fibre-fibre interactions. This work investigates the improvement of tensile properties of a flax/epoxy composite through the application of click chemistry reaction to a unidirectional-mat (UDM) reinforcement with modifications made on the short fibre mat and unidirectional flax fibre phases of the reinforcement. The surface of short flax fibres was fibrillated to increase the accessibility of hydroxyl groups for all preliminary reactions and the final click chemistry cross-linking, which creates stable covalent triazole bonds between azide and alkyne groups. A small percentage of treated nanocellulose was incorporated to further enhance the reinforcement properties. FTIR and EDX analysis confirmed the presence of the various functional groups on the surface of nanocellulose and flax fibres with very high degrees of substitution. The treatment significantly improved the mechanical properties of the dry reinforcement, including a 220% mean increase in the tensile strength. However, the treatments, particularly the addition of nanocellulose, resulted in a reduction in the permeability to liquid resin of the reinforcements, highlighting the need for compromises in their manufacture. Nonetheless, marked improvements in tensile strength and Young’s modulus were obtained for composites made of pre-compacted and cross-linked fibre preforms. Increases in elastic modulus, strength and strain at break of up to 50.1%, 53.8% and 10.1% were obtained, respectively.


  • Open Access

    Temperature Study during the Edge Trimming of Carbon Fiber-Reinforced Plastic [0]8/Ti6Al4V Stack Material

    by Arquimedes Castillo-Morales, Xavier Rimpault, Jean-François Chatelain, Gilbert Lebrun

    Carbon Fiber-Reinforced Plastic (CFRP) and Titanium alloy (Ti6Al4V) stacks are used extensively in the modern aerospace industry thanks to their outstanding mechanical properties and resistance to thermal load applications. Machining the CFRP/Ti6Al4V stack is a challenge and is complicated by the differences in each constituent materials’ machinability. The difficulty arises from the matrix degradation of the CFRP material caused by the heat generated during the machining process, which is a consequence of the low thermal conductivity of Ti6Al4V material. In most cases, CFRP and Ti6Al4V materials are stacked and secured together using rivets or bolts. This results in extra weight, while the drilling process required for such an assembly may damage the CFRP material. To overcome these issues, some applications employ an assembly that is free of bolts or rivets, and which uses adhesives or an adapted curing process to bond both materials together. The present research analyzes a thermal distribution and its effect on quality during the edge trimming process of a CFRP/Ti6Al4V stack assembly. Different types of tools and cutting parameters are compared using thermocouples embedded within the material and others on the tool cutting edge. In contrast to previous studies, the feed rate was the most significant factor affecting the cutting temperature and quality of the workpiece, while the cutting speed had no significant impact. The temperature in the workpiece increases as the feed per tooth decreases.


  • Open Access

    Effect of Graphene Additive on Flexural and Interlaminar Shear Strength Properties of Carbon Fiber-Reinforced Polymer Composite

    by Mohamed Ali Charfi, Ronan Mathieu, Jean-François Chatelain, Claudiane Ouellet-Plamondon, Gilbert Lebrun

    Composite materials are widely used in various manufacturing fields from aeronautic and aerospace industries to the automotive industry. This is due to their outstanding mechanical properties with respect to their light weight. However, some studies showed that the major flaws of these materials are located at the fiber/matrix interface. Therefore, enhancing matrix adhesion properties could significantly improve the overall material characteristics. This study aims to analyze the effect of graphene particles on the adhesion properties of carbon fiber-reinforced polymer (CFRP) through interlaminar shear strength (ILSS) and flexural testing. Seven modified epoxy resins were prepared with different graphene contents. The CFRP laminates were next manufactured using a method that guarantees a repeatable and consistent fiber volume fraction with a low porosity level. Short beam shear and flexural tests were performed to compare the effect of graphene on the mechanical properties of the different laminates. It was found that 0.25 wt.% of graphene filler enhanced the flexural strength by 5%, whilst the higher concentrations (2 and 3 wt.%) decreased the flexural strength by about 7%. Regarding the ILSS, samples with low concentrations (0.25 and 0.5 wt.%) demonstrated a decent increase. Meanwhile, 3 wt.% slightly decreases the ILSS.


  • Open Access

    A Study of the Interlaminar Fracture Toughness of Unidirectional Flax/Epoxy Composites

    by Yousef Saadati, Jean-Francois Chatelain, Gilbert Lebrun, Yves Beauchamp, Philippe Bocher, Nicolas Vanderesse

    Having environmental and economic advantages, flax fibers have been recognized as a potential replacement for glass fibers as reinforcement in epoxy composites for various applications. Its widening applications require employing failure criteria and analysis methods for engineering design, analysis, and optimization of this material. Among different failure modes, delamination is known as one of the earliest ones in laminated composites and needs to be studied in detail. However, the delamination characteristics of unidirectional (UD) flax/epoxy composites in pure Mode I has rarely been addressed, while Mode II and Mixed-mode I/II have never been addressed before. This work studies and evaluates the interlaminar fracture toughness and delamination behavior of UD flax/epoxy composite under Mode I, Mode II, and Mixed-mode I/II loading. The composites were tested following corresponding ASTM standards and fulfilled all the requirements. The interlaminar fracture toughness of the composite were determined and validated based on the specific characteristics of natural fibers. Considering the variation in the composite structure configuration and its effects, the results of interlaminar fracture toughness fit in the range of those reported for similar composites in the literature and provide a basis for the material properties of this composite.


  • Open Access

    Influence of Cutting Temperature on the Tensile Strength of a Carbon Fiber-Reinforced Polymer

    by Jérémy Delahaigue, Jean-Francois Chatelain, Gilbert Lebrun

    Carbon fiber-reinforced plastics (CFRP) have seen a significant increase in use over the years thanks to their specific properties. Despite continuous improvements in the production methods of laminated parts, a trimming operation is still necessary to achieve the functional dimensions required by engineering specifications. Laminates made of carbon fibers are very abrasive and cause rapid tool wear, and require high cutting temperatures. This creates damage to the epoxy matrix, whose glass-transition temperature is often recognized to be about 180 °C. This study aims to highlight the influence of the cutting temperature generated by tool wear on the surface finish and mechanical properties obtained from tensile tests. Trimming operations were performed on a quasi-isotropic 24-ply carbon/epoxy laminate, of 3.6 mm thickness, with a 6 flutes diamond-coated (CVD) cutter. The test specimens of 6 mm and 12 mm wide were obtained by trimming. The reduced width of the coupons allowed amplification of the effect of defects on the measured properties by increasing the proportion of coupon cross-section occupied by the defects. A new tool and a tool in an advanced state of wear were used to generate different cutting temperatures. Results showed a cutting temperature of 300 °C for the new tool and 475 °C for the worn tool. The analysis revealed that the specimens machined with the new tool have no thermal damage and the cut is clean. The plies oriented at −45° presented the worst surface finish according to the failure mode of the fiber. For the worn tool, the surface was degraded and the matrix was carbonized. After cutting, observations showed a degraded resin spread on the machined surface, which reduced the surface roughness and hid the cutting defects. In support of these observations, the tensile tests showed no variation of the mechanical properties for the 12 mm-wide specimens, but did show a 10% loss in mechanical properties for the 6 mm-wide specimens. These results suggest that the thermal defects caused by tool wear affect tensile properties, but only from a certain coupon width below which the machining defects increase their influence on the properties.


  • Thermostamping of [0/90]n carbon/peek laminates: Influence of support configuration and demolding temperature on part consolidation

    by Abdelhaq Benkaddour, Gilbert Lebrun, Louis Laberge‐Lebel

    This work presents experimental results on the thermostamping of carbon/PEEK cross‐ply laminates made of unidirectional prepregs. The first objective was to evaluate the effect of the supporting frame and laminate thickness on the consolidation quality of the final part. Based on the use of a square frame mounted with constant‐force springs clamps, three support configurations are compared: (i) clamp a polyimide film with the springs and use it to support the blank, (ii) support the blank with the constant‐force springs without polyimide film and (iii) support both the blank and a polyimide film with the springs. Using the best of these configurations (configurations ii and iii), the second objective was to push further the analysis and evaluate how demolding at different temperatures affects the part thickness distribution, the interlaminar shear strength and the cycle time of the process. Good consolidation qualities were obtained with configurations (ii) and (iii). However, the latter allows for more uniformity in the part thickness and higher shear strength when demolding at higher temperatures. It also allows a reduction of the molding cycle time considering the part can be demolded at a higher temperature (reduced cooling time). POLYM. COMPOS., 39:3341–3352, 2018. © 2017 Society of Plastics Engineers