ASAleksander Sokolov

Aleksander Sokolov

*This is an algorithmically generated author record based on publicly available information.

Aleksander Sokolov has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Towards Implementation of Online XRF Analysis of Rare Earth Elements and Heavy Metals on Conveyor Belts

    by Ulises Miranda Ordóñez, Pavels Kapitulskis, Vitalijs Kuzmovs, Aleksandr Sokolov, Vladimir Gostilo

    An X-ray fluorescence online analyzer was applied to the analysis of samples of known composition and concentration containing rare earth elements (REEs) and heavy metals (HMs), which were specially prepared by the authors (working samples). Reference samples were used for Th and U. The statistical parameters (detection limit, accuracy, and sensitivity) of the measurements of the spectra were calculated and a thorough assessment of the results was carried out. For large-volume samples, detection limits of 20–100 ppm for REEs and 10–140 ppm for HMs were achieved within 600 s. For thin-layer samples and similar geometries, detection limits for light and medium REEs improved to 3–20 ppm. The methodological possibilities for quantitative analysis of the REEs and HMs were examined and a rather simple approach with an easy implementation was developed. The method was tested in automatic measurements using concentrations in the range of 1000–4000 ppm, as a simulation of real-life measurements, and to determine the stability of the analyzer and the consistency of the results obtained. The results show that the online XRF analyzer can be applied for reliable detection and quantification of REEs and HMs at the ppm level. With these results, we are closer to obtaining results under conditions representative of those on real-world mining conveyor belts.

  • Open Access

    On-Line XRF Analysis of Elements in Minerals on a Conveyor Belt

    by Aleksander Sokolov, Vitalijs Kuzmovs, Ulises Miranda Ordóñez, Vladimir Gostilo

    Determination of the elemental composition of minerals and their derivatives at mining enterprises is important at all stages of minerals processing. This paper is devoted to the results of development and application of an online X-ray fluorescence (XRF) analysis method for monitoring mineral elements on a conveyor belt of mining enterprises. Evaluation of metrological characteristics achieved in the online analysis of lump, ore, charge feed, cake and slag materials on conveyor belt is presented. Each implementation of the online XRF analysis at mining enterprises was preceded by laboratory studies, development of measurement methods, calibration of a specific XRF analyzer using standard reference samples for a specific concentration range of the monitored elements. Typical areas of application for monitoring the concentration of elements in rocks on conveyor belts of mining enterprises and those solutions that made it possible to achieve the required measurement accuracy of an X-ray fluorescence analyzer in online mode are presented.


  • Open Access

    Industrial X-ray Fluorescence Analyzer for Real-Time Thickness Measurements of Aluminium Coatings on Rolled Steel

    by Aleksander Sokolov, Jelena Hasikova, Aleksejs Pecerskis, Vladimir Gostilo

    Aluminium coatings that are formed by physical vapour deposition (PVD) on rolled steel products are more resistant to atmospheric and seawater corrosion than zinc coatings. We developed a coating thickness analyzer (CTA) with an X-ray fluorescence (XRF) measuring head, that is integrated into the PVD pilot line. In this study, to conduct measurements of elements with atomic numbers less than 20 while avoiding the problem of registration of light elements, the measuring head was integrated into a process vacuum chamber to maintain a vacuum during the measurements. To validate the proposed tool, cold-rolled steel strips of different grades are used as substrates, and aluminium was deposited on the surface via PVD in thicknesses ranging from 1 to 20 g/m2. The thin-film thickness measurements during a pre-acceptance test were found to have a relative accuracy of less than 5% and a relative precision of less than 1–2%. The proposed CTA can be readily integrated in the factory’s automatic process control system and the real-time measurements in operating and calibration modes, and the status of all spectrometric equipment (X-ray tube, detector etc.) can be transmitted to the upper-level computer. Thus, the process engineer can properly control the deposition process.


  • Open Access

    Application of Industrial XRF Coating Thickness Analyzer for Phosphate Coating Thickness on Steel

    by Aleksandr Sokolov, Jelena Hasikova, Aleksej Pecerskis, Vladimir Gostilo, Ki Yong Lee, Hoobok Jung, Jung Hyun Lim

    The results of industrial application of an online X-ray fluorescence coating thickness analyzer for measuring the thickness of phosphate coatings on moving steel strips are considered in the article. The target range of coating thickness to be measured is from tens to hundreds of mg/m2 in a measurement time of 10 s. The measurement accuracy observed during long-duration factory acceptance test was 10–15%. The coating thickness analyzer consists of two XRF gauges, mounted above and below the steel strip and capable of moving across the moving strip system for their suspension and relocation and electronic control unit. Fully automated software was developed to automatically and continuously (24/7) control both gauges, scanning both sides of the steel strip, and develop and test methods for measuring new coatings. It allows performing offline storage and retrieval of the measurement results, remotely controlling the analyzer components and measurement modes from a control room. The developed XRF coating thickness analyzer can also be used for real-time measurement of other types of coatings, both metallic and non-metallic.


  • Open Access

    Development of portable HPGe spectrometer for in situ measurements

    by Artjoms Kail, Matthias Kaiser, Sergey Kim, Edward Loshevich, Alexander Sokolov

    In situ applications require a very high level of portability of high-resolution spectrometric equipment. Usage of HPGe detectors for radioactivity measurements in the environment or for nuclear safeguard applications, to combat illicit trafficking of nuclear materials or uranium and plutonium monitoring in nuclear wastes, has become a norm in the recent years. Portable HPGe-based radionuclide spectrometer with electrical cooling has lately appeared on the market for in situ applications. At the same time deterioration of energy resolution associated with vibrations produced by cryocooler or high weight of the instrument, short time of autonomous operation and high price of these spectrometers are limiting their usage in many cases. In this paper we present development results of ultra compact hand held all-in-one spectrometer for in situ measurements based on HPGe detector cooled by liquid nitrogen without listing the above disadvantages.


  • Support of Low-Level Instrument Background for HPGe Detectors

    by A. Sokolov, A. Starostin, V. Kuzmenko, A. Rozite

    The development results are presented for high-purity germanium (HPGe) detectors with low-level instrument background used in the Germanium Experiment on the measurement of Magnetic Moment of Antineutrino—GEMMA. Special design considerations for the cryostats have focused on mass reduction of materials surrounding the detector and the use of materials with very low radiation impurities.

  • On‐line analysis of chrome–iron ores on a conveyor belt using x‐ray fluorescence analysis

    by A. D. Sokolov, D. Docenko, E. Bliakher, O. Shirokobrod, Juha Koskinen

    We describe the method for and results of the application of an EDXRF on‐line analyzer for the analysis and quality testing of chrome–iron ores. For this task we used a BSI‐2000 analyzer for measurement of lumpy material being transported by a conveyor belt. The task of fully automated quantitative analysis of material on a conveyor belt is not very simple, as the results of measurements should not depend significantly on many factors, such as the distance to the measured material, the lump size, unknown and changing amounts of elements unseen by the analyzer; air and material humidity and ambient temperature. To solve most of these problems we used the program AssayKit for elemental and molecular composition calculation based on the fundamental parameters method. The chosen configuration of the x‐ray tube illumination cone and the detector registration cone allows measurements to be made at a wide range of distances between the analyzer and material. The XRF analyzer with this program was successfully applied to chrome–iron ore analysis in Kemi mine, Finland, for quality control of outgoing production. The accuracy of analysis—standard deviation of 1.1% for chrome and 0.8% for iron in full operation—was verified by more than 300 comparisons with chemical analysis measurements. Copyright © 2005 John Wiley & Sons, Ltd.