Andrzej Mlynarczak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Andrzej Mlynarczak has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Adam Piasecki
Institute of Materials Engineering, Poznan University of Technology, Poznan, Poland
2 shared publications - Dariusz Bartkowski
Faculty of Mechanical Engineering, Poznan University of Technology, Poznań, Poland
2 shared publications - Aneta Bartkowska
Faculty of Materials Engineering and Technical Physics, Poznan University of Technology, 61-138 Poznan, Poland
1 shared publication - Bartłomiej Dudziak1 shared publication
G. Mesmacque
Laboratoire de Mecanique de Lille (LML), U.R.A. C.N.R.S. 1441, F-59655 Villeneuve d'Ascq cédex, France
1 shared publication- K. Jozwiak
Laboratoire de Mecanique de Lille (LML), U.R.A. C.N.R.S. 1441, F-59655 Villeneuve d'Ascq cédex, France
1 shared publication
Latest Publications
- 1 October 2015
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 669, 158-166
Diffusion Niobizing of Titanium Grade 2 by Gas-Contact Method
The work presents results of diffusion niobizing of titanium Grade 2 by gas-contact method. Microhardness, thickness, chemical composition and microstructure were investigation. Diffusion processes was carried out in a two powder mixture. First consisted of ferro-niobium, kaolin and ammonium chloride, second mixture contained pure niobium instead ferro-niobium. The processes were carried out at 950°C, 1000°C and 1050°C for 2, 4 and 6 hours. Due to the geometric surface structure quality and other properties like thickness or microhardness, the best diffusion layer was obtained using first powder mixture and following parameters: temperature 950°C and time of diffusion equal 2 hours. The diffusion layer established in these conditions, had structure of niobium solution in titanium, and niobium content of about 10%. Its hardness was 550 HV0.05 while thickness was 120 μm.
- 1 October 2015
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 669, 158-166
Diffusion Niobizing of Titanium Grade 2 by Gas-Contact Method
The work presents results of diffusion niobizing of titanium Grade 2 by gas-contact method. Microhardness, thickness, chemical composition and microstructure were investigation. Diffusion processes was carried out in a two powder mixture. First consisted of ferro-niobium, kaolin and ammonium chloride, second mixture contained pure niobium instead ferro-niobium. The processes were carried out at 950°C, 1000°C and 1050°C for 2, 4 and 6 hours. Due to the geometric surface structure quality and other properties like thickness or microhardness, the best diffusion layer was obtained using first powder mixture and following parameters: temperature 950°C and time of diffusion equal 2 hours. The diffusion layer established in these conditions, had structure of niobium solution in titanium, and niobium content of about 10%. Its hardness was 550 HV0.05 while thickness was 120 μm.
- Top Cited Papers
- 1 May 2015
- Published by Elsevier in Optics & Laser Technology
- Vol. 68, 191-201
Microstructure, microhardness and corrosion resistance of Stellite-6 coatings reinforced with WC particles using laser cladding
- 1 May 2015
- Published by Elsevier in Optics & Laser Technology
- Vol. 68, 191-201
Top Cited PapersMicrostructure, microhardness and corrosion resistance of Stellite-6 coatings reinforced with WC particles using laser cladding
- 13 February 2006
- Published by Wiley in Advanced Engineering Materials
- Vol. 8 (1-2) , 119-123
Early Stage of Diffusional Formation of Carbide Coatings on Steels
Despite much research on different aspects of the formation of diffusion carbide coatings (DCC) there is still no complex description of the early stage of the formation of chromium, vanadium and titanium carbides. However, the knowledge of this stage of diffusional processes enables the control the useful coating properties. This paper presents new insights for better understanding of the mechanism of the early stage of V, Ti, Cr DCC growth on a steel matrix.
- 13 February 2006
- Published by Wiley in Advanced Engineering Materials
- Vol. 8 (1-2) , 119-123
Early Stage of Diffusional Formation of Carbide Coatings on Steels
Despite much research on different aspects of the formation of diffusion carbide coatings (DCC) there is still no complex description of the early stage of the formation of chromium, vanadium and titanium carbides. However, the knowledge of this stage of diffusional processes enables the control the useful coating properties. This paper presents new insights for better understanding of the mechanism of the early stage of V, Ti, Cr DCC growth on a steel matrix.
- 1 November 2003
- Published by Wiley in Advanced Engineering Materials
- Vol. 5 (11) , 789-793
Wear Resistance of Multiphase Diffusion Carbide Coatings
Diffusion carbide coatings of the types M7C3‐VC and M7C3‐TiC have been fabricated by pack cementation at 1000 °C on three tool steels. Coating hardness increases with FeV and FeTi concentration, while metallic luster increases with FeCr content. Wear behavior was found to be independent of the steel matrix; maximum wear resistance was achieved for M7C3‐VC‐TiC with Ti/V/Cr = 4/4/2. The Figure shows the shear of micro‐roughness on one of the coatings.
- 1 November 2003
- Published by Wiley in Advanced Engineering Materials
- Vol. 5 (11) , 789-793
Wear Resistance of Multiphase Diffusion Carbide Coatings
Diffusion carbide coatings of the types M7C3‐VC and M7C3‐TiC have been fabricated by pack cementation at 1000 °C on three tool steels. Coating hardness increases with FeV and FeTi concentration, while metallic luster increases with FeCr content. Wear behavior was found to be independent of the steel matrix; maximum wear resistance was achieved for M7C3‐VC‐TiC with Ti/V/Cr = 4/4/2. The Figure shows the shear of micro‐roughness on one of the coatings.