TKTsukasa Kiyoshi

Tsukasa Kiyoshi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tsukasa Kiyoshi has a total of 80 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Operation of Wax-Impregnated GdBCO Layer-Wound Coil Using Cryocoolers

    by S. Matsumoto, T. Kiyoshi, A. Miyazoe, A. Otsuka, M. Hamada, H. Maeda, Y. Yanagisawa, H. Nakagome, H. Suematsu

    RE-Ba-Cu-O (REBCO) high-temperature superconducting conductors have the advantage of high critical current density in a magnetic field above 10 T as well as tolerance to high tensile stress. REBCO high-temperature superconducting coils are expected to be applied to superconducting magnets using cryocoolers. While epoxy-resin-impregnated superconducting coils are considered to be appropriate for superconducting magnets using cryocoolers because the impregnation provides sufficient thermal conductivity, the degradation of epoxy-resin-impregnated REBCO coils due to extremely low nominal cleavage strength is a serious problem. This problem is negligible for wax (paraffin)-impregnated REBCO coils. A wax-impregnated GdBCO layer-wound coil using cryocoolers was successfully operated at a current between $-$300 and 300 A.


  • Upgrade Design to a Cryogen-Free 20-T Superconducting Outsert for a 47-T Hybrid Magnet

    by K. Watanabe, S. Awaji, Y. Hou, H. Oguro, T. Kiyoshi, H. Kumakura, S. Hanai, H. Tsubouchi, M. Sugimoto, I. Inoue

    A Rutherford flat cable composed of sixteen 0.8-mm-diameter Nb 3 Sn strands with CuNb-reinforced stabilizers (CuNb/Nb 3 Sn) has been developed for use as an outsert for a 47-T hybrid magnet. To guarantee the safety of the magnet in the event of a quench, the low residual resistance ratio characteristic of arc-melted-in-situ CuNb composite had to be improved upon, and to obtain high electric conductivity, a new CuNb fabrication method using a Nb rod was attempted. The thermal runaway characteristics of chemical vapor deposition- YBa 2 Cu 3 O 7-δ (Y123) coated-conductor tapes with varying Cu stabilizer thicknesses were measured in magnetic fields of up to 10 T at temperatures ranging from 17 to 60 K. It was found that the ratio of the thermal runaway over-current to the critical current decreases as temperature decreases and that thermal runaway occurs just above the critical current level at 5 K. The properties of a cryogen-free, 20-T superconducting outsert for a 47-T hybrid magnet utilizing CuNb/Nb 3 Sn Rutherford flat cables and Y123 tapes and having a room temperature bore of 400 mm were investigated.


  • Hybrid Magnet Design Consisting of a 20 T Superconducting Outsert and a 15 MW Resistive Insert

    by K. Watanabe, S. Awaji, H. Oguro, K. Takahashi, K. Minegishi, T. Suwa, Y. Sasaki, T. Kiyoshi, T. Asano, S. Hanai, et al.

    Internally reinforced Nb3Sn strands with CuNb-reinforcing stabilizer have been developed for realizing a compact high-field superconducting magnet. The Rutherford flat cables composed of sixteen strands were made with a 0.8 mm diameter CuNb/Nb3Sn strand. The designed critical current of the CuNb/Nb3Sn Rutherford flat cable is Ic = 1890 A at 13 T and 4.2 K in case of an ordinary heat-treatment at 670 for 96 h, which is two times higher than an operation current desired for safety margin. In addition, mechanical characteristics for CVD-processed YBa2Cu3O7 (YBCO) coated-conductor tapes were measured at 4.2 K in fields up to 18 T. It was found that YBCO tape exhibits the irreversible strain 0.5% and the irreversible stress 1140 MPa for the critical current at 4.2 K and 18 T for B//c. The cabling-and-react+prebending-processed CuNb/Nb3Sn Rutherford flat cables and CVD-processed YBCO tapes will be used as a react-and-wind method for the development of a 20 T superconducting magnet with a wide room temperature bore. We design a 20 T-440 mm warm-bore superconducting magnet consisting of YBCO inner coils, middle coils, and NbTi outer coils, which has the coil parameters of inner diameter 480 mm, outer diameter 1283 mm, and coil height 1302 mm. Since the coil inductance is estimated to be 232 H, the magnetic stored energy is 94 MJ at an operation current 900 A. An energy-saving 47 T hybrid magnet can be constructed in combination with a wide-bore 20 T superconducting outsert and a 15 MW-27 T water-cooled resistive insert.


  • Evaluation of the Screening Current in a 1.3 GHz NMR Magnet Using ReBCO

    by A. Otsuka, Y. Yanagisawa, T. Kiyoshi, H. Maeda, H. Nakagome, M. Takeda

    NMR magnets using high- T c superconductors (HTS) are currently by several organizations designed to generate high fields exceeding 25 T. In such designs, the HTS are used for the inner coils, and the outer coils consist of NbTi and Nb 3 Sn wires. A ReBCO wire with a Hastelloy substrate has excellent critical current performance over wide range of magnetic fields and tolerates high tensile stress up to 700 MPa. We have previously shown conceptual designs in which the main coils are assumed to use ReBCO wires. The designs suggest the potential to realize much more compact and lightweight magnets than conventional magnets with low- T c superconductors (LTS) and HTS. On the other hand, the problem of screening current induced by the perpendicular field remains to be solved. In this study, we evaluate numerically the amount of the magnetic field generated by the screening current in ReBCO coils. Compensation coils for improving field homogeneity were found to reduce the shielding current by several percentage points. The improved coil arrangement is reported considering the shielding current effect.


  • A 1.3 GHz NMR Magnet Design Under High Hoop Stress Condition

    by A. Otsuka, T. Kiyoshi, M. Takeda

    NMR magnets using high-Tc superconductors (HTS) to generate high magnetic fields exceeding 25 T are currently being designed by several organizations. In these designs, the HTS is used for the inner coils, and the other coils consist of NbTi and Nb3Sn wires. The YBCO wire, which is a typical HTS, has excellent critical current performance over a wide range of magnetic fields and tolerates high tensile stress of up to 700 MPa. These properties make it possible to realize a high-field NMR magnet. In particular, the superior mechanical strength allows for the high-stress criterion of the electromagnetic force to be applied to the design of the magnets. In this study, we show the conceptual design of 1.3 GHz (30.5 T) NMR magnets under the condition of high hoop stress of 500 MPa. To achieve high magnetic field homogeneity in these designs, we propose three magnet design plans that have different arrangements of the compensation coils. We assumed that the magnet would be operated by the driven mode at 4.2 K. We also considered the strong angular dependence of the critical current of the YBCO wires to design the magnet.


  • Electrical and Mechanical Properties of DI-BSCCO Type HT Reinforced With Metallic Sheathes

    by Naoki Ayai, Kouhei Yamazaki, Masashi Kikuchi, Goro Osabe, Hideo Takaaze, Hiromitsu Takayama, Shin-Ichi Kobayashi, Jun Fujikami, Kazuhiko Hayashi, Ken-Ichi Sato, et al.

    Electrical and mechanical characteristics of Type HT tape, which is standard 4.2 mm wide DI-BSCCO tape reinforced with metallic tapes, have been evaluated. Longitudinal distributions of critical current and n-index in kilometer long Type HT tape has proved uniform from end to end just like the original insert tape, which is Type H tape. Type HT-CA reinforced with 50 mum thick heat-resistant copper alloy is highly balanced tape with high mechanical properties and low splice resistance. Type HT-SS reinforced with 20 mum thick stainless steel has the best mechanical properties, which has been demonstrated under the actual environment in high field magnet, namely the hoop stress load test energizing a one-turn coil in external high magnetic field and liquid helium.


  • The Electrical and Mechanical Characterization of Metal-Reinforced Bi-2223/Ag Conductors for High Field Insert Coil

    by Seyong Choi, Tsukasa Kiyoshi, Shinji Matsumoto, Davide Uglietti, Kyoji Zaitsu, Takashi Hase, Mamoru Hamada

    In this study, we investigated in field properties of high-Tc superconductor (HTS) tapes electrically as well as mechanically. Metallic reinforced Bi-2223/Ag superconductor tapes were used in this work. The critical current (Ic), which is highly dependent on the magnetic field, was measured using fields applied parallel and perpendicular to the tape surface. The conductor was exposed to fields of up to 28 T at 4.2 K. In order to confirm the performance of tapes in practical NMR operation, Ic was also measured around 2 K. The conductor was wound on a large diameter bobbin and mechanical properties were then measured as the coil current was increased. Finally, we verified the conductor properties from coil Ic and maximum stress/strain of it.


  • Magnetic Flux Concentrator Using Gd-Ba-Cu-O Bulk Superconductors

    by T. Kiyoshi, S. Choi, S. Matsumoto, T. Asano, D. Uglietti

    Magnetic flux concentration is a very important technique for the effective generation of high magnetic fields. We propose the use of the diamagnetism of a high T c bulk superconductor (HTS bulk) instead of ferromagnetic materials such as Ho and Dy. We fabricated a magnetic field concentrator using Gd-Ba-Cu-O bulk. The essential point was slits to suppress the current along the circumference. The concentrator was cooled at the center of a superconducting magnet with liquid helium. By increasing the external field to 1.00 T, a magnetic flux density of 3.20 T was obtained at the center of the concentrator. At an external field of 2.00 T, a field of 5.65 T was also obtained. A magnetic lens using HTS bulk was successfully demonstrated. The experimental results were well explained by numerical analyses assuming HTS bulk as a perfect conductor.


  • 20 T Compact Superconducting Outsert Employing Y123 Coated Conductors for a 45 T Hybrid Magnet

    by K. Watanabe, S. Awaji, G. Nishijima, T. Hamajima, T. Kiyoshi, H. Kumakura, S. Hanai, K. Koyanagi, M. Ono

    We have been developing high-strength Nb3Sn strand cables to construct a high-field superconducting outsert for a 45 T hybrid magnet with a 25 T water-cooled resistive magnet. Evidence for cold work strengthening of repeated bending treatment (prebending effect) on Nb3Sn strands internally reinforced with CuNb stabilizer, which exhibits significant enhancement of the critical current density, has been found in the superconducting magnet fabrication process using a react-and-wind method. The strand cables were designed by controlling the constituent number of CuNb/Nb3Sn strands with the prebending effect and stainless steel strands, which are expected to have a stress limit 580 MPa at 0.4% strain. In order to design a compact superconducting outsert, high-strength strand cables are adopted in a magnetic field region below 14 T to maintain relatively large engineering current densities (Je). In a higher-field region above 14 T, YBa2Cu3O7 (Y123) coated conductors are employed for an insert coil. Using combination of Y123, Nb3Sn and NbTi superconductors, a 20 T superconducting outsert with a room temperature bore of 400 mm consisting of three layers made of Y123, two layers of CuNb/Nb3Sn and two layers of NbTi was designed. The coil parameters are 440 mm inner diameter, 1080 mm outer diameter and 1138 mm coil height. A very compact 20 T superconducting outsert with a stored magnetic energy 72 MJ at an operation current 903 A can be developed for a 45 T hybrid magnet.


  • HTS Magnetic Field Damper for Short-Term Fluctuations in the Driven-Mode

    by A. Otsuka, T. Kiyoshi, S. Matsumoto

    Although high-temperature superconductors (HTS) are very promising for high-field generation over 25 Tesla, it is difficult to apply them to an NMR magnet because of their low index values and the difficulty caused by superconducting joints. The properties of HTS appear to cause poor magnetic field stability in the persistent-mode operation. Therefore, in this study, a high-field NMR magnet including HTS coils will be operated in the driven-mode. We evaluated the magnetic field drift of a 14 Tesla (600 MHz) NMR magnet in the driven-mode. The magnetic field stability in several hours was about 2 ppm. However, in a shorter-term, magnetic field fluctuations with a main period of approximately 0.01 Hz remained. These fluctuations are unfavorable for a precise NMR measurement. In order to reduce the field fluctuation, we tested the damper coil by making a closed-loop circuit using Bi-2223 tapes. The damper coil was cooled by a single-stage GM cryocooler in the magnetic field. The inside magnetic field of the damper coil was measured with an NMR Teslameter. The shielding current in the damper coil canceled out the field fluctuation, which indicates that the damper coil worked effectively.