Christian Olagnon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Christian Olagnon has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- R. Estevez
Centre National de la Recherche Scientifique
2 shared publications - Belynda Benane
Univ Lyon, INSA-Lyon, MATEIS, UMR CNRS 5510—7 avenue Jean Capelle, F-69621 Villeurbanne, France
1 shared publication - Bernard Yrieix
EDF R&D
1 shared publication C Tallaron
1 shared publicationE. Lataste
MATEIS, INSA-Lyon, UMR 5510, 20, Avenue Albert Einstein, 69621 Villeurbanne, France
1 shared publicationG. Fantozzi
MATEIS, INSA-Lyon, UMR 5510, 20, Avenue Albert Einstein, 69621 Villeurbanne, France
1 shared publication
Latest Publications
- Open Access
Instrumented Indentation of Super-Insulating Silica Compacts
Highly porous silica compacts for superinsulation were characterized by instrumented indentation. Samples showed a multi-scale stacking of silica particles with a total porous fraction of 90 vol %. The two main sources of silica available for the superinsulation market were considered: fumed silica and precipitated silica. The compacts processed with these two silica displayed different mechanical properties at a similar porosity fraction, thus leading to different usage properties, as the superinsulation market requires sufficient mechanical properties at the lowest density. The measurement of Young’s modulus and hardness was possible with spherical indentation, which is an efficient method for characterizing highly porous structures. Comparison of the mechanical parameters measured on silica compacts and silica aerogels available from the literature was made. Differences in mechanical properties between fumed and precipitated compacts were explained by structural organization.
Open AccessInstrumented Indentation of Super-Insulating Silica Compacts
Highly porous silica compacts for superinsulation were characterized by instrumented indentation. Samples showed a multi-scale stacking of silica particles with a total porous fraction of 90 vol %. The two main sources of silica available for the superinsulation market were considered: fumed silica and precipitated silica. The compacts processed with these two silica displayed different mechanical properties at a similar porosity fraction, thus leading to different usage properties, as the superinsulation market requires sufficient mechanical properties at the lowest density. The measurement of Young’s modulus and hardness was possible with spherical indentation, which is an efficient method for characterizing highly porous structures. Comparison of the mechanical parameters measured on silica compacts and silica aerogels available from the literature was made. Differences in mechanical properties between fumed and precipitated compacts were explained by structural organization.
- 22 March 2015
- Published by Springer Nature in Materials and Structures
- Vol. 49 (4) , 1555-1568
Earthen construction: an increase of the mechanical strength by optimizing the dispersion of the binder phase
- 22 March 2015
- Published by Springer Nature in Materials and Structures
- Vol. 49 (4) , 1555-1568
Earthen construction: an increase of the mechanical strength by optimizing the dispersion of the binder phase
- 31 March 2009
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 29 (4) , 587-594
Microstructural and mechanical consequences of thermal cycles on a high zirconia fuse-cast refractory
- 31 March 2009
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 29 (4) , 587-594
Microstructural and mechanical consequences of thermal cycles on a high zirconia fuse-cast refractory
- Open Access
- 1 November 2006
- Published by EDP Sciences in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Vol. 61 (6) , 765-771
Cohesive Zone Description and Quantitative Analysis of Glassy Polymer Fracture
-Modélisation par zone cohésive et étude expérimentale de la rupture des polymères vitreux-Le craquelage est décrit à l'aide d'une zone cohésive qui prend en compte l'amorçage, l'élargissement des surfaces des craquelures jusqu'à la rupture des fibrilles qui correspond à la création d'une fissure localement. Une calibration des paramètres de la zone cohésive est présentée pour le PMMA (Polymethyl methacrylate). Nous montrons qu'il est nécessaire de décrire le craquelage à l'aide d'une zone cohésive viscoplastique pour rendre compte des effets de la vitesse de chargement sur la ténacité du matériau, qui dépend des conditions de sollicitation.
- 1 November 2006
- Published by EDP Sciences in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
- Vol. 61 (6) , 765-771
Open AccessCohesive Zone Description and Quantitative Analysis of Glassy Polymer Fracture
-Modélisation par zone cohésive et étude expérimentale de la rupture des polymères vitreux-Le craquelage est décrit à l'aide d'une zone cohésive qui prend en compte l'amorçage, l'élargissement des surfaces des craquelures jusqu'à la rupture des fibrilles qui correspond à la création d'une fissure localement. Une calibration des paramètres de la zone cohésive est présentée pour le PMMA (Polymethyl methacrylate). Nous montrons qu'il est nécessaire de décrire le craquelage à l'aide d'une zone cohésive viscoplastique pour rendre compte des effets de la vitesse de chargement sur la ténacité du matériau, qui dépend des conditions de sollicitation.