YBYuelong Bai

Yuelong Bai

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yuelong Bai has a total of 29 co-authors. Here are the top co-authors by number of shared publications:

  • Zhifeng Zhang

    National Engineering Research Center for Non-ferrous Metal Composites, GRINM Group, Beijing 100088, China

    8 shared publications
  • Jun Xu

    General Research Institute for Non-ferrous Metals

    6 shared publications
  • Weimin Mao

    School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China

    4 shared publications
  • Bao Li

    National Engineering & Technology Research Center for Non-Ferrous Metal Composites, GRINM Group, Beijing 100088, China

    2 shared publications
  • Hansen Zheng

    National Engineering & Technology Research Center for Non-Ferrous Metal Matrix Composites, GRINM Group Co., Ltd., No.11, Xingke East Street, Yanqi Economic Development Zone, Huairou District, Beijing 101407, China

    2 shared publications
  • Hong Xu

    Research Center for Foundry Engineering, North University of China, Taiyuan 030051, China

    2 shared publications

Latest Publications

  • Open Access

    Effects of ESMT on Microstructure and Mechanical Properties of Al-8Zn-2Mg-1.5Cu-0.15Sc-0.15Zr Cast Alloy in Squeeze Casting Process

    by Yongtao Xu, Zhifeng Zhang, Purui Zhao, Zhihua Gao, Yuelong Bai, Weimin Mao

    Al-8Zn-2Mg-1.5Cu-0.15Sc-0.15Zr alloy with high-strength performance as well as good castability has been developed. In this study, effects of electromagnetic stirring melt treatment (ESMT) on microstructure and mechanical properties of the alloy in the squeeze casting process were investigated. The results show that solidification structure and mechanical properties are significantly improved by ESMT; compared with the conventional squeeze casting, the average grain size decreases from 112 μm without ESMT to 53 μm with ESMT. Meanwhile coarse primary Al3(Sc, Zr) particles unavoidably occurred in cases without ESMT disappear, and segregation degree of the main elements of Zn, Mg, Cu are greatly alleviated; the tensile strength increases from 590 MPa to 610 MPa, and the elongation increases from 9% to 11%. The structure refinement and homogenization should owe to uniform temperature and composition distribution by ESMT under squeeze casting with rapid solidification.


  • Open Access

    Effect of Sc on the Hot Cracking Properties of 7xxx Aluminum Alloy and the Microstructure of Squeeze Castings

    by Yongtao Xu, Zhifeng Zhang, Zhihua Gao, Yuelong Bai, Purui Zhao, Weimin Mao

    In this paper, the effect of adding the refiner Sc to the high Zn/Mg ratio 7xxx series aluminum alloy melt on the hot tearing performance, microstructure, and mechanical properties of the alloy is studied. The hot tearing performance test (CRC) method is used to evaluate the hot tearing performance of the alloy. The squeeze casting process was used to form solid cylindrical parts to analyze the structure and properties of the alloy. This study shows that the hot cracking sensitivity of the alloy after the addition of the refiner Sc is significantly reduced. The ingot grain size is significantly reduced, and the average grain size is reduced from about 86 μm to about 53 μm. While the mechanical properties are significantly improved, and the tensile strength reduced from 552 MPa is increased to 571 MPa, and the elongation rate is increased from 11% to 14%.


  • Open Access

    Numerical Simulation and Experimental Study on Compound Casting of Layered Aluminum Matrix Composite Brake Drum

    by Hansen Zheng, Zhifeng Zhang, Yuelong Bai

    The requirements of high-strength, wear-resistance and lightweight of brake drums have been continually increasing in recent years and any specific aluminum alloy or particle-reinforced aluminum matrix composites may not satisfy all the demands. Combining dissimilar materials to play their respective advantages is a solution to this problem. In this study, a compound casting method was used to combine solid SiCp/A357 composite and a liquid 7050 aluminum alloy to prepare an aluminum matrix composite with a layered structure. The ProCAST numerical simulation software was used to predict the heat transfer in compound casting process and guide the preheating temperature of the wear-resistant ring in the experiment. An Optical Microscope (OM) and Scanning Electron Microscope (SEM) were used to observe microstructures around the solid–liquid bonding interface, the element distribution and phase component of which were analyzed by Energy Dispersive Spectroscopy (EDS) and mechanical properties were evaluated by microhardness and shear tests. The results showed that the interface of the layered aluminum matrix composite prepared by this method achieved complete metallurgical bonding and a transition zone formed on the solid surface. After T6 heat treatment, the average shear strength of the interface increased from 19.8 MPa to 33.8 MPa.


  • Open Access

    Research on Microstructure and Mechanical Properties of Rheological Die Forging Parts of Al-6.54Zn-2.40Cu-2.35Mg-0.10Zr(-Sc) Alloy

    by Hansen Zheng, Zhifeng Zhang, Yuelong Bai, Yongtao Xu

    High-strength aluminum alloy (mainly refers to the 7xxx series) is the optimum material for lightweight military equipment. However, this type of aluminum alloy is a wrought aluminum alloy. If it is directly formed by traditional casting methods, there will inevitably be problems such as coarseness, unevenness, looseness, and hot cracking in the structure, which will greatly affect the final performance of the part. Based on the internal cooling with annular electromagnetic stirring (IC-AEMS) method, a new technology of rheological die forging is developed in this paper, and the scale-reduced parts of a brake hub of Al-6.54Zn-2.40Cu-2.35Mg-0.10Zr aluminum alloy were prepared. The influence of IC-AEMS and the addition of rare element Sc on the structure and mechanical properties of the parts was studied. An optical microscope and scanning electron microscope (SEM) were used to observe the microstructure evolution, energy dispersive spectroscopy (EDS) was used to analyze the phase distribution and composition, and the mechanical properties of the parts were tested by uniaxial tensile tests. The results show that the addition of Sc element can effectively refine the grains and improve the strength and elongation of the material; the application of IC-AEMS improves the cooling rate of the melt, increases the effective nucleation rate, and the grains are further refined. Through process optimization, scale-reduced parts of a brake hub with good formability and mechanical properties can be obtained, the ultimate tensile strength is 597.2 ± 3.1 MPa, the yield strength is 517.8 ± 4.3 MPa, and the elongation is 13.7 ± 1.3%.


  • Open Access

    Enhanced Refinement of Al-Zn-Mg-Cu-Zr Alloy via Internal Cooling with Annular Electromagnetic Stirring above the Liquidus Temperature

    by Tianyang Guan, Zhifeng Zhang, Yuelong Bai, Bao Li, Ping Wang

    There are two critical stages of grain refinement during solidification: above and below the liquidus temperature. The key to improve the refinement potential is ensuring the nucleation sites precipitate in large quantities and dispersed in the melt above liquidus. In this work, internal cooling with annular electromagnetic stirring was applied to an Al-Zn-Mg-Cu-Zr alloy at a temperature above liquidus. A systematic experimental study on the grain refining potential was performed by combining different melt treatments and pouring temperatures. The results indicate that internal cooling with annular electromagnetic stirring (IC-AEMS) had a significantly superior grain refining potency for the alloy compared to traditional electromagnetic stirring (EMS). In addition, homogeneous and refined grains were achieved at high pouring temperatures with IC-AEMS. The possible mechanisms for the enhanced grain refinement above the liquidus temperature are explained as the stable chilling layer around the cooling rod in IC-AEMS providing undercooling for the precipitation of Al3Zr nucleant particles and the high cooling rate restraining the growth rate of these particles. At the same time, forced convection promotes a more homogeneous distribution of nucleant particles.


  • Open Access

    Numerical and Experimental Study on Melt Treatment for Large-Volume 7075 Alloy by a Modified Annular Electromagnetic Stirring

    by Min He, Zhifeng Zhang, Weimin Mao, Bao Li, Yuelong Bai, Jun Xu

    This study presents a modified annular electromagnetic stirring (M-AEMS) melt treatment suitable for a large-volume and high-alloyed aluminum alloy. A 3D computational model coupling an electromagnetic model with a macroscopic heat and fluid-flow model was established by using Ansoft Maxwell 3D and Fluent from ANSYS workbench, and the effects of the electromagnetic shielding ring, the height of the magnet yoke, the shape of the iron core, and the internal cooling mandrel on the electromagnetic, thermal and flow fields were studied numerically. Based on the optimal technical parameters, the effectivity of the M-AEMS process by using 7075 alloy was validated experimentally. The results show that a favorable electromagnetic field distribution can be achieved by changing the magnet yoke height, the iron-core shape and the electromagnetic shielding ring, and the melt temperature of the 7075 alloy can drop rapidly to the pouring temperature by imposing the internal cooling mandrel; compared with ordinary annular electromagnetic stirring, the M-AEMS process creates a lower magnetic strength near the melt top, beneficial for stabilizing the melt surface; meanwhile, it yields a higher magnetic strength near the melt bottom, which increases the shear rate and ensures an optimal stirring effect. Therefore, M-AEMS works more efficiently because the thermal and composition fields become uniform in a shorter time, which reduces the average grain size and the composition segregation, and a more stable melt surface can be obtained during treatment, which reduces the number of air and oxide inclusions in the melt.


  • Open Access

    The Influence of Inter-Cooling and Electromagnetic Stirring above Liquidus on the Formation of Primary Al3Zr and Grain Refinement in an Al-0.2%Zr Alloy

    by Tianyang Guan, Zhifeng Zhang, Yuelong Bai, Min He, Hansen Zheng, Haodong Zhao, Xiaopeng Li, Ping Wang

    The nucleation and grain growth that occur during solidification have been extensively examined, but insight into the influence of an external field on the formation of heterogeneous crystal nuclei above the liquidus remains unclear in the peritectic refinement mechanism. In this work, we studied the effect of cooling rate above the liquidus on the formation of primary Al3Zr and grain refinement in Al-0.2%Zr alloys with inter-cooling annular electromagnetic stirring (IC-AEMS). The results show that the size and distribution of primary Al3Zr are greatly improved, and the morphology transformed from large plate/blocky shapes without IC-AEMS to small blocks with IC-AEMS. Meanwhile, above the liquidus, the addition of an Al-Zr master alloy to pure Al alone did little to enhance the refinement, but after IC-AEMS, the grains were refined dramatically. The refinement result seems to be explained by two hypotheses of pre-nucleation and explosive nucleation.


  • Design and Numerical Simulation of a Novel Mixer in Preparing SiCp/A357 Composites

    by Yuelong Bai, Zhenlin Zhang, Zhifeng Zhang, Chunsheng Chen, Jun Xu