Nathan F. Gardner
Research Subjects
Nathan F. Gardner has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Frank M. Steranka
Lumileds Lighting, San Jose, California, USA
2 shared publications - Jonathan J. Wierer
North Carolina State University
2 shared publications - M. George Craford
Lumileds Lighting, San Jose, California, USA
2 shared publications - Michael R. Krames
Arkesso, LLC
2 shared publications Dong Li
Univ. of New Mexico (United States)
1 shared publicationJ. C. Kim
Advanced Laboratories, Lumileds Lighting , 370 West Trimble Road, San Jose, California 95131
1 shared publication
Latest Publications
- 15 September 2007
- Published by Wiley
Diodes, Light‐emitting
- 7 March 2005
- Published by AIP Publishing in Applied Physics Letters
- Vol. 86 (11)
Polarization anisotropy in the electroluminescence of m-plane InGaN–GaN multiple-quantum-well light-emitting diodes
multiple-quantum-well light-emitting diodes were fabricated on plane films grown on plane substrates. The [0001] axis of the epitaxial film is parallel to the [0001] axis of the substrate. The surface is striated, with features running perpendicular to the axis and a maximum surface height difference of . Electroluminescence shows strong polarization anisotropy, with more light emitted with polarization perpendicular to the axis compared to parallel to the axis. An Ahrrenius fit of the polarization ratio indicates that there is a difference in the energy gap between the two polarization states. This suggests that a high polarization ratio can be maintained at the high temperatures and drive current densities required for high-power light-emitting diode applications.- 7 March 2005
- Published by AIP Publishing in Applied Physics Letters
- Vol. 86 (11)
Polarization anisotropy in the electroluminescence of m-plane InGaN–GaN multiple-quantum-well light-emitting diodes
multiple-quantum-well light-emitting diodes were fabricated on plane films grown on plane substrates. The [0001] axis of the epitaxial film is parallel to the [0001] axis of the substrate. The surface is striated, with features running perpendicular to the axis and a maximum surface height difference of . Electroluminescence shows strong polarization anisotropy, with more light emitted with polarization perpendicular to the axis compared to parallel to the axis. An Ahrrenius fit of the polarization ratio indicates that there is a difference in the energy gap between the two polarization states. This suggests that a high polarization ratio can be maintained at the high temperatures and drive current densities required for high-power light-emitting diode applications.- 7 March 2005
- Published by SPIE-Intl Soc Optical Eng
- Vol. 5739, 102-108
III-nitride LEDs with photonic crystal structures
Electrical operation of III-Nitride light emitting diodes (LEDs) with photonic crystal structures is demonstrated. Employing photonic crystal structures in III-Nitride LEDs is a method to increase light extraction efficiency and directionality. The photonic crystal is a triangular lattice formed by dry etching into the III-Nitride LED. A range of lattice constants is considered (a ~ 270 - 340nm). The III-Nitride LED layers include a tunnel junction providing good lateral current spreading without a semi-absorbing metal current spreader as is typically done in conventional III-Nitride LEDs. These photonic crystal III-Nitride LED structures are unique because they allow for carrier recombination and light generation proximal to the photonic crystal (light extraction area) yet displaced from the absorbing metal contact. The photonic crystal Bragg scatters what would have otherwise been guided modes out of the LED, increasing the extraction efficiency. The far-field light radiation patterns are heavily modified compared to the typical III-Nitride LED’s Lambertian output. The photonic crystal affects the light propagation out of the LED surface, and the radiation pattern changes with lattice size. LEDs with photonic crystals are compared to similar III-Nitride LEDs without the photonic crystal in terms of extraction, directionality, and emission spectra.
- 7 March 2005
- Published by SPIE-Intl Soc Optical Eng
- Vol. 5739, 102-108
III-nitride LEDs with photonic crystal structures
Electrical operation of III-Nitride light emitting diodes (LEDs) with photonic crystal structures is demonstrated. Employing photonic crystal structures in III-Nitride LEDs is a method to increase light extraction efficiency and directionality. The photonic crystal is a triangular lattice formed by dry etching into the III-Nitride LED. A range of lattice constants is considered (a ~ 270 - 340nm). The III-Nitride LED layers include a tunnel junction providing good lateral current spreading without a semi-absorbing metal current spreader as is typically done in conventional III-Nitride LEDs. These photonic crystal III-Nitride LED structures are unique because they allow for carrier recombination and light generation proximal to the photonic crystal (light extraction area) yet displaced from the absorbing metal contact. The photonic crystal Bragg scatters what would have otherwise been guided modes out of the LED, increasing the extraction efficiency. The far-field light radiation patterns are heavily modified compared to the typical III-Nitride LED’s Lambertian output. The photonic crystal affects the light propagation out of the LED surface, and the radiation pattern changes with lattice size. LEDs with photonic crystals are compared to similar III-Nitride LEDs without the photonic crystal in terms of extraction, directionality, and emission spectra.
- 15 October 2004
- Published by Wiley
Diodes, Light‐emitting