Chang-Chou Hwang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chang-Chou Hwang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
C. H. Liang
Cycling & Health Tech Industry R&D Center, 17, 37 Rd., Taichung Industry Park, Taichung, Taiwan, R.O.C.
1 shared publicationC. L. Tien
Department of Electrical Engineering, Feng Chia University, 100, Wenhwa Rd., Seatwen, Taichung, Taiwan, ROC
1 shared publicationChia-Yu Chang
Department of Electrical Engineering, Feng Chia University, Taichung, Taiwan, ROC
1 shared publication- Chih-Hong Lin
Department of Electrical Engineering, National United University, Miaoli, Taiwan
1 shared publication Chong Jie Hong
Graduate Institute of Electrical and Communications Engineering, Feng Chia University, Taichung, Taiwan, ROC
1 shared publication- Chuen-Lin Tien
Department of Electrical Engineering, Feng Chia University, Taichung 407, Taiwan
1 shared publication
Latest Publications
- Open Access
High Performances Design of a Six-Phase Synchronous Reluctance Motor Using Multi-Objective Optimization with Altered Bee Colony Optimization and Taguchi Method
A two-step optimal design with multi-objective functions by using two kinds of optimization methods for a six-phase synchronous reluctance motor is applied in a centrifugal compressor to achieve minimum cost, lower torque ripple, maximum efficiency and higher power factor. In the first-step procedure, the optimal design with multi-objective functions by use of the altered bee colony optimization (BCO) and the Taguchi method combined with finite element analysis (FEA) is used for optimizing the barrier shape and size in the rotor to reduce torque ripple, raise power factor, maximum efficiency and raise output torque. In the second-step procedure, the optimal design with multi-objective functions by means of the altered BCO and the Taguchi method combined with FEA is applied for optimizing the geometry of stator to reduce manufacturing cost, stator iron weight and stator winding weight. Finally, some experimental results show the effectiveness of the proposed techniques.
Open AccessHigh Performances Design of a Six-Phase Synchronous Reluctance Motor Using Multi-Objective Optimization with Altered Bee Colony Optimization and Taguchi Method
A two-step optimal design with multi-objective functions by using two kinds of optimization methods for a six-phase synchronous reluctance motor is applied in a centrifugal compressor to achieve minimum cost, lower torque ripple, maximum efficiency and higher power factor. In the first-step procedure, the optimal design with multi-objective functions by use of the altered bee colony optimization (BCO) and the Taguchi method combined with finite element analysis (FEA) is used for optimizing the barrier shape and size in the rotor to reduce torque ripple, raise power factor, maximum efficiency and raise output torque. In the second-step procedure, the optimal design with multi-objective functions by means of the altered BCO and the Taguchi method combined with FEA is applied for optimizing the geometry of stator to reduce manufacturing cost, stator iron weight and stator winding weight. Finally, some experimental results show the effectiveness of the proposed techniques.
- 2 January 2017
- Published by Taylor & Francis in Smart Science
- Vol. 5 (1) , 21-38
The Development of Direct-drive High-speed Brushless Permanent Magnet Motors for Machine Tools
This paper describes the development of surface-mounted permanent magnet (SPM) motors for use in direct-drive high-speed spindle machine tools. For such applications, motors should be highly efficient, have low torque ripple, and minimal package size and weight. Based on average torque, torque ripple, and efficiency, four SPM motor designs were chosen for comparison. Two configurations, 2-pole with 3-slots and 2-pole with 18-slots, were selected for analysis. The Taguchi method was used to refine stator structure and to determined how well the selected motors reduced losses. The effect of magnet span angles and winding arrangements on torque ripple, average torque, and the efficiency of 2-pole/18-slot motors was also investigated. A thermal analysis was conducted to determine temperature distribution within the motors. The motor performance was also studied using a Matlab/Simulink model. Experimental measurements and finite element analysis (FEA) were used to examine and validate the results.
- 2 January 2017
- Published by Taylor & Francis in Smart Science
- Vol. 5 (1) , 21-38
The Development of Direct-drive High-speed Brushless Permanent Magnet Motors for Machine Tools
This paper describes the development of surface-mounted permanent magnet (SPM) motors for use in direct-drive high-speed spindle machine tools. For such applications, motors should be highly efficient, have low torque ripple, and minimal package size and weight. Based on average torque, torque ripple, and efficiency, four SPM motor designs were chosen for comparison. Two configurations, 2-pole with 3-slots and 2-pole with 18-slots, were selected for analysis. The Taguchi method was used to refine stator structure and to determined how well the selected motors reduced losses. The effect of magnet span angles and winding arrangements on torque ripple, average torque, and the efficiency of 2-pole/18-slot motors was also investigated. A thermal analysis was conducted to determine temperature distribution within the motors. The motor performance was also studied using a Matlab/Simulink model. Experimental measurements and finite element analysis (FEA) were used to examine and validate the results.
- 5 June 2009
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 20 (7) , 075202
Magnetic field sensor based on double-sided polished fibre-Bragg gratings
A new magnetic field sensor based on double-sided polished fibre-Bragg gratings (FBGs) coated with an iron thin film for measuring magnetic flux density was experimentally demonstrated with the sensitivity of 25.6 nm T−1. The sensing mechanism is based on the Bragg wavelength shift as the magnetic field is measured by the proposed sensing head. Results of this study present the intensity of the reflected optical signal as a function of the applied strain on the FBG. This paper shows that an improved method for sensing the wavelength shift with changes in external magnetic field is developed by use of the double-sided polished FBGs.
- 5 June 2009
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 20 (7) , 075202
Magnetic field sensor based on double-sided polished fibre-Bragg gratings
A new magnetic field sensor based on double-sided polished fibre-Bragg gratings (FBGs) coated with an iron thin film for measuring magnetic flux density was experimentally demonstrated with the sensitivity of 25.6 nm T−1. The sensing mechanism is based on the Bragg wavelength shift as the magnetic field is measured by the proposed sensing head. Results of this study present the intensity of the reflected optical signal as a function of the applied strain on the FBG. This paper shows that an improved method for sensing the wavelength shift with changes in external magnetic field is developed by use of the double-sided polished FBGs.
- 14 December 2007
- Published by Wiley in physica status solidi (c)
- Vol. 4 (12) , 4635-4638
Performance and applications of a small PM generator
- 14 December 2007
- Published by Wiley in physica status solidi (c)
- Vol. 4 (12) , 4635-4638
Performance and applications of a small PM generator
- 14 December 2007
- Published by Wiley in physica status solidi (c)
- Vol. 4 (12) , 4639-4642
Design and construction of a claw-pole PM dynamo
- 14 December 2007
- Published by Wiley in physica status solidi (c)
- Vol. 4 (12) , 4639-4642
Design and construction of a claw-pole PM dynamo