Antonio Ludovico Beraldo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Antonio Ludovico Beraldo has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Juarez Benigno Paes
Department of Forest and Wood Sciences, Federal University of Espírito Santo, Jerônimo Monteiro, Brazil
2 shared publications - Marina Donária Chaves Arantes
Universidade Federal de São João del-Rei
2 shared publications - Rogy Frigeri Tiburtino
Engenheiro Florestal Programa de Pós Graduação em Ciências Florestais Universidade Federal do Espírito Santo Msc. Av. Governador Lindemberg 316 29550-000 Jerônimo Monteiro (ES Centro CEP Brasil
2 shared publications C. O. Brossard
Universidad de Oriente Sede Mella Facultad de Ingeniería Química
1 shared publicationE. D. Maury
Universidad de Oriente Sede Mella Facultad de Ingeniería Química
1 shared publicationG.C.S. Ferreira
State University of Campinas, Brazil
1 shared publication
Latest Publications
- Open Access
Study of the Pozzolanic Reactivity of Sugar Cane Straw Ashes (SCSA) Burned under Controlled Conditions
The aims of this work were to evaluate the reactivity of sugarcane straw ashes (SCSA) burned under controlled conditions and to analyze their reactivity in blended cement and hydrated lime pastes by thermogravimetric analysis (TG) and calorimetry. Four different ashes were produced, and burned at 600 °C, 700 °C, 800 °C and 900 °C (SCSA600, SCSA700, SCSA800 and SCSA900, respectively). These ashes were characterized by X-ray fluorescence spectroscopy, X-ray diffractometry, particle size distribution by laser diffraction and specific area surfaces to assess their potential interest in the partial replacement of inorganic binders (Portland cement (OPC) and hydrated lime). The hydrated lime pastes were subjected to scanning electron microscopy (SEM) and TG. The blended cement pastes were analyzed by TG and calorimetry, compressive strength testing and mercury intrusion porosimetry. High lime fixation percentages were observed in the hydrated lime and OPC pastes and were higher than 75% and 50% for the ashes burned at 600 °C and 700 °C, respectively. Calorimetry showed a delay in the heat release of SCSA600 and SCSA700 compared to the control paste. These pastes also had higher compressive strength and a smaller total pore volume. The results indicate the positive response of preparing sugar cane ashes under controlled conditions (mainly for straw calcined within the 600–700 °C range) for their use as pozzolanic addition by partially replacing inorganic binders.
Open AccessStudy of the Pozzolanic Reactivity of Sugar Cane Straw Ashes (SCSA) Burned under Controlled Conditions
The aims of this work were to evaluate the reactivity of sugarcane straw ashes (SCSA) burned under controlled conditions and to analyze their reactivity in blended cement and hydrated lime pastes by thermogravimetric analysis (TG) and calorimetry. Four different ashes were produced, and burned at 600 °C, 700 °C, 800 °C and 900 °C (SCSA600, SCSA700, SCSA800 and SCSA900, respectively). These ashes were characterized by X-ray fluorescence spectroscopy, X-ray diffractometry, particle size distribution by laser diffraction and specific area surfaces to assess their potential interest in the partial replacement of inorganic binders (Portland cement (OPC) and hydrated lime). The hydrated lime pastes were subjected to scanning electron microscopy (SEM) and TG. The blended cement pastes were analyzed by TG and calorimetry, compressive strength testing and mercury intrusion porosimetry. High lime fixation percentages were observed in the hydrated lime and OPC pastes and were higher than 75% and 50% for the ashes burned at 600 °C and 700 °C, respectively. Calorimetry showed a delay in the heat release of SCSA600 and SCSA700 compared to the control paste. These pastes also had higher compressive strength and a smaller total pore volume. The results indicate the positive response of preparing sugar cane ashes under controlled conditions (mainly for straw calcined within the 600–700 °C range) for their use as pozzolanic addition by partially replacing inorganic binders.
- Open Access
- 1 June 2015
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 39 (3) , 567-574
RESISTÊNCIA DE DUAS ESPÉCIES DE BAMBU TRATADAS CONTRA FUNGOS XILÓFAGOS
O objetivo deste trabalho foi avaliar a resistência de bambus das espécies Bambusa vulgaris e Dendrocalamus giganteus após serem expostos a três métodos de tratamentos químicos preservativos, contra a ação dos fungos Postia placenta e Polyporus fumosus. Os métodos de tratamento empregados foram o de transpiração (diafragma íntegro e rompido), imersão prolongada e Boucherie modificado. As hastes de bambu foram transformadas em colmos de 2,0 m de comprimento e tratadas em solução de 1 ou 3% de ingredientes ativos (i.a.) de um produto comercial à base de cobre, cromo e boro (CCB). Nos métodos por transpiração e imersão prolongada, os colmos foram expostos nas soluções por períodos de 5, 10 ou 15 dias, enquanto no método de Boucherie modificado não houve segregação do tratamento entre tempos de tratamento. Para avaliar a eficiência dos tratamentos, foram empregados os fungos Postia placenta e Polyporus fumosus. A partir dos resultados, observou-se que, em média, em ambas as espécies de bambu tratadas e métodos empregados, a perda de massa das amostras de bambu, depois de submetidas ao ataque dos fungos, foi baixa, tendo variado de 2,44 a 14,26%.
- 1 June 2015
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 39 (3) , 567-574
Open AccessRESISTÊNCIA DE DUAS ESPÉCIES DE BAMBU TRATADAS CONTRA FUNGOS XILÓFAGOS
O objetivo deste trabalho foi avaliar a resistência de bambus das espécies Bambusa vulgaris e Dendrocalamus giganteus após serem expostos a três métodos de tratamentos químicos preservativos, contra a ação dos fungos Postia placenta e Polyporus fumosus. Os métodos de tratamento empregados foram o de transpiração (diafragma íntegro e rompido), imersão prolongada e Boucherie modificado. As hastes de bambu foram transformadas em colmos de 2,0 m de comprimento e tratadas em solução de 1 ou 3% de ingredientes ativos (i.a.) de um produto comercial à base de cobre, cromo e boro (CCB). Nos métodos por transpiração e imersão prolongada, os colmos foram expostos nas soluções por períodos de 5, 10 ou 15 dias, enquanto no método de Boucherie modificado não houve segregação do tratamento entre tempos de tratamento. Para avaliar a eficiência dos tratamentos, foram empregados os fungos Postia placenta e Polyporus fumosus. A partir dos resultados, observou-se que, em média, em ambas as espécies de bambu tratadas e métodos empregados, a perda de massa das amostras de bambu, depois de submetidas ao ataque dos fungos, foi baixa, tendo variado de 2,44 a 14,26%.
- Open Access
- 1 March 2015
- Published by FapUNIFESP (SciELO) in Floresta e Ambiente
- Vol. 22 (1) , 124-133
Tratamento Preservativo de Duas Espécies de Bambu por Imersão Prolongada e Boucherie Modificado
O objetivo desta pesquisa foi avaliar a qualidade do tratamento preservativo das espécies de bambu Dendrocalamus giganteus e Bambusa vulgaris submetidas a dois métodos de tratamento. Os bambus foram colhidos em touceiras em Alegre e Jerônimo Monteiro, sul do Espírito Santo. As hastes foram seccionadas em colmos de 2,0 m de comprimento e tratadas em soluções de 1 e 3% de ingredientes ativos (i.a.) de um produto à base de cobre, cromo e boro (CCB). No método de imersão prolongada, os colmos foram imersos na solução por 5, 10 e 15 dias. No método de Boucherie modificado, a solução penetrou no bambu pela ação de uma pressão de 0,7 MPa. Foi avaliada a qualidade do tratamento por meio da penetração e da retenção do CCB nos colmos. Houve maior penetração de i.a. na base dos colmos e a retenção ficou abaixo da recomendada pela norma brasileira para tratamento de madeira.
- 1 March 2015
- Published by FapUNIFESP (SciELO) in Floresta e Ambiente
- Vol. 22 (1) , 124-133
Open AccessTratamento Preservativo de Duas Espécies de Bambu por Imersão Prolongada e Boucherie Modificado
O objetivo desta pesquisa foi avaliar a qualidade do tratamento preservativo das espécies de bambu Dendrocalamus giganteus e Bambusa vulgaris submetidas a dois métodos de tratamento. Os bambus foram colhidos em touceiras em Alegre e Jerônimo Monteiro, sul do Espírito Santo. As hastes foram seccionadas em colmos de 2,0 m de comprimento e tratadas em soluções de 1 e 3% de ingredientes ativos (i.a.) de um produto à base de cobre, cromo e boro (CCB). No método de imersão prolongada, os colmos foram imersos na solução por 5, 10 e 15 dias. No método de Boucherie modificado, a solução penetrou no bambu pela ação de uma pressão de 0,7 MPa. Foi avaliada a qualidade do tratamento por meio da penetração e da retenção do CCB nos colmos. Houve maior penetração de i.a. na base dos colmos e a retenção ficou abaixo da recomendada pela norma brasileira para tratamento de madeira.
- Open Access
- 4 October 2013
- Published by Universidade Federal do Parana in FLORESTA
- Vol. 44 (1) , 11-20
AVALIAÇÃO DO TRATAMENTO PRESERVATIVO DE TALISCAS DE BAMBU COM ÁCIDO PIROLENHOSO
A baixa resistência natural do bambu ao ataque de organismos xilófagos constitui uma das principais limitações ao seu pleno uso. O objetivo do presente estudo foi avaliar o efeito do ácido pirolenhoso no tratamento preservativo de taliscas de bambu-gigante contra fungos deterioradores. Para tal, foi realizado um ensaio de apodrecimento acelerado em laboratório com taliscas testemunhas (sem tratamento) e taliscas tratadas com o produto diluído em água fervente nas concentrações 0%, 5%, 10%, 20% e 30%, adotando-se tempos de imersão 15, 45, 90 e 180 minutos. As taliscas de bambu foram testadas após 6 e 16 semanas de exposição. Foram efetuadas inspeções visuais nas taliscas e aplicados ensaios não destrutivos de perda de massa e por ultrassom (6 e 16 semanas) e ensaios de flexão estática (após 16 semanas). Os resultados obtidos nos ensaios não destrutivos não evidenciaram o efeito dos fatores testados (tipo de solo, duração do tratamento e concentração da solução) nessas propriedades. A análise visual indicou apenas um ataque superficial nas taliscas, não evidenciando perda de massa. No ensaio de flexão estática, verificou-se o efeito favorável da duração do tratamento nos módulos de elasticidade (Em0) e de ruptura (MOR). O tipo de solo (natural ou estéril) não apresentou influência no módulo de elasticidade, enquanto que a concentração da solução não influenciou o módulo de ruptura. Palavras-chave: Bambu-gigante; biodeterioração; fungos deterioradores. Abstract Evaluation of preservative treatment of bamboo strips with pyroligneous acid. Bamboo presents a low natural resistance to decay, which constitutes one of the major limitations to its use. This study aims to evaluate pyroligneous acid effect against fungal bamboo deterioration through an accelerated laboratory decay with testing reference (without treatment) and treated specimens with the product diluted in boiling water at (0%, 5%, 10%, 20% and 30%) in different immersion times (15, 45, 90, and 180 minutes). Bamboo splits were evaluated after 6 and 16 weeks of exposure. Visual inspections and non-destructive tests (mass loss and ultrasound at 6 and 16 weeks) and bending (after 16 weeks) were applied to the bamboo strips. Results of the non-destructive tests did not allow to detect the effect of the factors (soil type, immersion time and solution concentration) on these properties. Only a superficial attack was observed by visual inspection, which did not denote mass loss. Immersion time shows a positive effect on modulus of elasticity (Em0) and on modulus of rupture (MOR). Moduli of elasticity and rupture were not influenced by soil type (sterile or natural), or by the concentration of the solution, respectively. Keywords: Giant bamboo; biodeterioration; fungi decay.
- 4 October 2013
- Published by Universidade Federal do Parana in FLORESTA
- Vol. 44 (1) , 11-20
Open AccessAVALIAÇÃO DO TRATAMENTO PRESERVATIVO DE TALISCAS DE BAMBU COM ÁCIDO PIROLENHOSO
A baixa resistência natural do bambu ao ataque de organismos xilófagos constitui uma das principais limitações ao seu pleno uso. O objetivo do presente estudo foi avaliar o efeito do ácido pirolenhoso no tratamento preservativo de taliscas de bambu-gigante contra fungos deterioradores. Para tal, foi realizado um ensaio de apodrecimento acelerado em laboratório com taliscas testemunhas (sem tratamento) e taliscas tratadas com o produto diluído em água fervente nas concentrações 0%, 5%, 10%, 20% e 30%, adotando-se tempos de imersão 15, 45, 90 e 180 minutos. As taliscas de bambu foram testadas após 6 e 16 semanas de exposição. Foram efetuadas inspeções visuais nas taliscas e aplicados ensaios não destrutivos de perda de massa e por ultrassom (6 e 16 semanas) e ensaios de flexão estática (após 16 semanas). Os resultados obtidos nos ensaios não destrutivos não evidenciaram o efeito dos fatores testados (tipo de solo, duração do tratamento e concentração da solução) nessas propriedades. A análise visual indicou apenas um ataque superficial nas taliscas, não evidenciando perda de massa. No ensaio de flexão estática, verificou-se o efeito favorável da duração do tratamento nos módulos de elasticidade (Em0) e de ruptura (MOR). O tipo de solo (natural ou estéril) não apresentou influência no módulo de elasticidade, enquanto que a concentração da solução não influenciou o módulo de ruptura. Palavras-chave: Bambu-gigante; biodeterioração; fungos deterioradores. Abstract Evaluation of preservative treatment of bamboo strips with pyroligneous acid. Bamboo presents a low natural resistance to decay, which constitutes one of the major limitations to its use. This study aims to evaluate pyroligneous acid effect against fungal bamboo deterioration through an accelerated laboratory decay with testing reference (without treatment) and treated specimens with the product diluted in boiling water at (0%, 5%, 10%, 20% and 30%) in different immersion times (15, 45, 90, and 180 minutes). Bamboo splits were evaluated after 6 and 16 weeks of exposure. Visual inspections and non-destructive tests (mass loss and ultrasound at 6 and 16 weeks) and bending (after 16 weeks) were applied to the bamboo strips. Results of the non-destructive tests did not allow to detect the effect of the factors (soil type, immersion time and solution concentration) on these properties. Only a superficial attack was observed by visual inspection, which did not denote mass loss. Immersion time shows a positive effect on modulus of elasticity (Em0) and on modulus of rupture (MOR). Moduli of elasticity and rupture were not influenced by soil type (sterile or natural), or by the concentration of the solution, respectively. Keywords: Giant bamboo; biodeterioration; fungi decay.
- Open Access
- 1 June 2013
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 6 (3) , 392-398
Nonconventional concrete hollow blocks evaluation by destructive and non-destructive testing
The aim of this study was to evaluate cementitious matrices properties by partial replacement of Portland cement by silica fume (SF) or by rice husk ash (RHA), and their application in nonbearing hollow blocks, tested by destructive and non-destructive methods. The following mixtures were produced: reference (100% of Portland cement) and Portland cement replacement (10% by mass) with SF or RHA. The non-destructive testing showed that the highest values of UPV were obtained for SF-based blocks and RHA-based blocks. The destructive test showed better results for SF-based blocks, but there was no statistical difference between the RHA-based and control ones.
- 1 June 2013
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 6 (3) , 392-398
Open AccessNonconventional concrete hollow blocks evaluation by destructive and non-destructive testing
The aim of this study was to evaluate cementitious matrices properties by partial replacement of Portland cement by silica fume (SF) or by rice husk ash (RHA), and their application in nonbearing hollow blocks, tested by destructive and non-destructive methods. The following mixtures were produced: reference (100% of Portland cement) and Portland cement replacement (10% by mass) with SF or RHA. The non-destructive testing showed that the highest values of UPV were obtained for SF-based blocks and RHA-based blocks. The destructive test showed better results for SF-based blocks, but there was no statistical difference between the RHA-based and control ones.
- Open Access
- 1 September 2011
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 17 (3) , 361-367
Effects of thermal treatment on the physicochemical characteristics of giant bamboo
Despite countless use possibilities for bamboo, this material has two major disadvantages. One drawback is the low natural durability of most bamboo species due to presence of starch in their parenchyma cells. The other equally important drawback is the tendency bamboo has to present dimensional variations if subjected to environmental change conditions. In an attempt to minimize these inconveniences, strips (laths) of Dendrocalamus giganteus Munro were taken from different portions of the culm and subjected to several temperatures, namely 140 ºC, 180 ºC, 220 ºC, 260 ºC and 300 ºC under laboratory conditions, at the ESALQ-USP college of agriculture. The thermal treatment process was conducted in noninert and inert atmospheres (with nitrogen), depending on temperature Specimens were then subjected to physicomechanical characterization tests in order to determine optimum thermal treatment conditions in which to preserve to the extent possible the original bamboo properties. Results revealed that there is an optimum temperature range, between 140 º and 220 ºC, whereby thermally treated bamboo does not significantly lose its mechanical properties while at the same time showing greater dimensional stability in the presence of moisture.
- 1 September 2011
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 17 (3) , 361-367
Open AccessEffects of thermal treatment on the physicochemical characteristics of giant bamboo
Despite countless use possibilities for bamboo, this material has two major disadvantages. One drawback is the low natural durability of most bamboo species due to presence of starch in their parenchyma cells. The other equally important drawback is the tendency bamboo has to present dimensional variations if subjected to environmental change conditions. In an attempt to minimize these inconveniences, strips (laths) of Dendrocalamus giganteus Munro were taken from different portions of the culm and subjected to several temperatures, namely 140 ºC, 180 ºC, 220 ºC, 260 ºC and 300 ºC under laboratory conditions, at the ESALQ-USP college of agriculture. The thermal treatment process was conducted in noninert and inert atmospheres (with nitrogen), depending on temperature Specimens were then subjected to physicomechanical characterization tests in order to determine optimum thermal treatment conditions in which to preserve to the extent possible the original bamboo properties. Results revealed that there is an optimum temperature range, between 140 º and 220 ºC, whereby thermally treated bamboo does not significantly lose its mechanical properties while at the same time showing greater dimensional stability in the presence of moisture.
- Open Access
- 1 December 2008
- Published by FapUNIFESP (SciELO) in Brazilian Journal of Chemical Engineering
- Vol. 25 (4) , 723-728
The role of phenols from bagasse vacuum pyrolysis bio-oil in cupper sulfured ore flotation
Vacuum pyrolysis bagasse bio-oil collected in a series of sequential fractions was analyzed for total percentage of phenols and levoglucosan components. It was established that the ratio total phenols- to-levoglucosan could be used as an indicator of the performance of alkaline solutions of bio-oil fractions (SABO) when they are used as foaming agents to benefit flotation of sulfured cupper minerals. A high total phenol-to-levoglucosan ratio results in high percentages of Cu in cupper flotation concentrates, L Cu. A closer look at the role of individual phenols reveals that p-cresol is the main phenol, although not the only one, responsible for the observed behavior. Additionally it was noted that rather high doses of these foaming agents must be used to obtain desirable results in flotation processes. A production cost estimate allows consideration of SABO as an alternative to others commercial foaming agents, especially if an optimization study reduces doses of SABO.
- 1 December 2008
- Published by FapUNIFESP (SciELO) in Brazilian Journal of Chemical Engineering
- Vol. 25 (4) , 723-728
Open AccessThe role of phenols from bagasse vacuum pyrolysis bio-oil in cupper sulfured ore flotation
Vacuum pyrolysis bagasse bio-oil collected in a series of sequential fractions was analyzed for total percentage of phenols and levoglucosan components. It was established that the ratio total phenols- to-levoglucosan could be used as an indicator of the performance of alkaline solutions of bio-oil fractions (SABO) when they are used as foaming agents to benefit flotation of sulfured cupper minerals. A high total phenol-to-levoglucosan ratio results in high percentages of Cu in cupper flotation concentrates, L Cu. A closer look at the role of individual phenols reveals that p-cresol is the main phenol, although not the only one, responsible for the observed behavior. Additionally it was noted that rather high doses of these foaming agents must be used to obtain desirable results in flotation processes. A production cost estimate allows consideration of SABO as an alternative to others commercial foaming agents, especially if an optimization study reduces doses of SABO.