Yoshiyuki Mohri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yoshiyuki Mohri has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Toshinori Kawabata
6 shared publications- Hoe I. Ling
Department of Civil Engineering and Engineering Mechanics, Columbia University, New York, USA
5 shared publications - Fumio Tatsuoka
東京大学・東京理科大
3 shared publications - Mitsuru Ariyoshi
Institute for rural engineering, NARO
3 shared publications - Toshinori Kawabata
Graduate School of Agricultural Science, Kobe University, Kobe, Japan
3 shared publications Daisuke Shoda
Associate Professor, Graduate School of Agricultural Science, Kobe University, Rokkodai 1-1, Nada, Kobe, 657-8501 Japan;
2 shared publications
Latest Publications
- 1 January 2014
- Published by The Japanese Geotechnical Society in Japanese Geotechnical Journal
- Vol. 9 (3) , 443-455
Method of in-situ rotation shear test for an embankment slope using a sounding borehole
- 1 January 2014
- Published by The Japanese Geotechnical Society in Japanese Geotechnical Journal
- Vol. 9 (3) , 443-455
Method of in-situ rotation shear test for an embankment slope using a sounding borehole
- 17 August 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1015-1024
Dynamic Behavior of Buried Flexible Pipes of Varying Thickness Using the Shaking Table Test
In designing a pipeline, deflection and stress of the pipe are calculated through structural analysis based on bending ring stiffness EI/D3 . The pipes with equivalent bending ring stiffness would have the same behavior in design. However, it is easily understandable that the behavior of pipe may be influenced not only by EI/D3, but also by the relationships between E and I. In this paper, shaking table test for buried flexible pipes were conducted to evaluate the effects of pipe thickness on the dynamic behavior. Some pipes having approximately equivalent bending ring stiffness and different thickness were used. In this experiment, these pipes were buried in the laminar box and shaken by horizontal sine wave. As a result, it was found that the larger bending strain and radial stress of the pipe occurred with the thinner wall. This result suggests that the probability of the buckling of the pipe is higher on thinner pipes. It is evident that the pipelines for irrigation should be designed in consideration of this fact.
- 17 August 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 1015-1024
Dynamic Behavior of Buried Flexible Pipes of Varying Thickness Using the Shaking Table Test
In designing a pipeline, deflection and stress of the pipe are calculated through structural analysis based on bending ring stiffness EI/D3 . The pipes with equivalent bending ring stiffness would have the same behavior in design. However, it is easily understandable that the behavior of pipe may be influenced not only by EI/D3, but also by the relationships between E and I. In this paper, shaking table test for buried flexible pipes were conducted to evaluate the effects of pipe thickness on the dynamic behavior. Some pipes having approximately equivalent bending ring stiffness and different thickness were used. In this experiment, these pipes were buried in the laminar box and shaken by horizontal sine wave. As a result, it was found that the larger bending strain and radial stress of the pipe occurred with the thinner wall. This result suggests that the probability of the buckling of the pipe is higher on thinner pipes. It is evident that the pipelines for irrigation should be designed in consideration of this fact.
- 11 March 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 3158-3165
Experiments and Numerical Analyses for Spillway on Small Earth Dam Subjected to Simple Shear
The purpose of this study is to clarify the dynamic behavior of spillway on soil subjected to cyclic simple shear, which modeled earthquake vibration. In this study, small-scale simple shear tests with aluminum rods and numerical simulations using the 2-dimensional discrete element method (DEM) were conducted. The results demonstrated that the spillway inclines from side to side and gradually floats up. The uplift displacement of spillway reinforced by geogrid models was smaller than that of unreinforced spillway because geogrid models prevented the ground from displacing toward the bottom of the spillway model and the forces from acting on the sidewall of spillway.
- 11 March 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 3158-3165
Experiments and Numerical Analyses for Spillway on Small Earth Dam Subjected to Simple Shear
The purpose of this study is to clarify the dynamic behavior of spillway on soil subjected to cyclic simple shear, which modeled earthquake vibration. In this study, small-scale simple shear tests with aluminum rods and numerical simulations using the 2-dimensional discrete element method (DEM) were conducted. The results demonstrated that the spillway inclines from side to side and gradually floats up. The uplift displacement of spillway reinforced by geogrid models was smaller than that of unreinforced spillway because geogrid models prevented the ground from displacing toward the bottom of the spillway model and the forces from acting on the sidewall of spillway.
- 1 January 2010
- Published by Japan Chapter of International Geosynthetics Society in Jioshinsetikkusu Rombunshu (Geosynthetics Engineering Journal)
- Vol. 25, 27-32
BEHAVIOR OF SHALLOWLY BURIED PIPE USING GEOGRID FOR LATERAL LOADING
- 1 January 2010
- Published by Japan Chapter of International Geosynthetics Society in Jioshinsetikkusu Rombunshu (Geosynthetics Engineering Journal)
- Vol. 25, 27-32
BEHAVIOR OF SHALLOWLY BURIED PIPE USING GEOGRID FOR LATERAL LOADING
- 1 January 2010
- Published by Japan Chapter of International Geosynthetics Society in Jioshinsetikkusu Rombunshu (Geosynthetics Engineering Journal)
- Vol. 25, 127-132
DYNAMIC BEHAVIOR FOR SPILLWAY WITH GEOSYNTHETICS SUBJECTED TO SIMPLE SHEAR
- 1 January 2010
- Published by Japan Chapter of International Geosynthetics Society in Jioshinsetikkusu Rombunshu (Geosynthetics Engineering Journal)
- Vol. 25, 127-132
DYNAMIC BEHAVIOR FOR SPILLWAY WITH GEOSYNTHETICS SUBJECTED TO SIMPLE SHEAR
- 1 August 2009
- Published by Emerald Publishing in Geosynthetics International
- Vol. 16 (4) , 246-273
New direction for earth reinforcement: disaster prevention for earthfill dams
A large number of geosynthetic-reinforcing technologies for embankments and retaining walls have been proposed and developed, and the behaviour of these structures has been evaluated using laboratory tests and field tests, as well as full-scale case histories. Yet a great number of embankments have failed in Japan owing to strong seismic loads and heavy rainfall. Significant improvements are required in the construction of earthfill dams to prevent these failures. This paper reviews the characteristic features of the damage to small earthfill dams that has taken place during earthquakes as well as heavy rainfall. The paper then describes a new technology using geosynthetic soil bags with extended tails stacked on the downstream slope to construct earthfill dams that are highly stable against earthquakes as well as heavy rainfall leading to overtopping by flood water. Some fundamental aspects of the stability of embankments reinforced by soil bags and seismic behaviour are examined using static loading, hydraulic breach tests and shaking-table tests.
- 1 August 2009
- Published by Emerald Publishing in Geosynthetics International
- Vol. 16 (4) , 246-273
New direction for earth reinforcement: disaster prevention for earthfill dams
A large number of geosynthetic-reinforcing technologies for embankments and retaining walls have been proposed and developed, and the behaviour of these structures has been evaluated using laboratory tests and field tests, as well as full-scale case histories. Yet a great number of embankments have failed in Japan owing to strong seismic loads and heavy rainfall. Significant improvements are required in the construction of earthfill dams to prevent these failures. This paper reviews the characteristic features of the damage to small earthfill dams that has taken place during earthquakes as well as heavy rainfall. The paper then describes a new technology using geosynthetic soil bags with extended tails stacked on the downstream slope to construct earthfill dams that are highly stable against earthquakes as well as heavy rainfall leading to overtopping by flood water. Some fundamental aspects of the stability of embankments reinforced by soil bags and seismic behaviour are examined using static loading, hydraulic breach tests and shaking-table tests.
- 17 July 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Field Measurement and Numerical Analysis for Buried Large Diameter Steel Pipes
This paper presents an overview of field tests for buried pipe, which were conducted using steel pipes with 3500 mm diameter and 26 mm thickness. In this full-scale test, five kinds of construction site were employed. The depth of soil cover was approximately 3.0 m in every case. Sheet pile method was employed in Case-5, and open-cut method was conducted in the other cases. Displacement transducers were installed in the pipe and strain gauges were circumferentially attached to the inner of the pipe. The deformation of pipe was observed for over a year by those measures. Therefore, it is found that the behavior of the buried pipe was strongly influenced by backfilling methods. In addition, FEM analyses were conducted to confirm the behavior of soil-pipe interaction. Thus, it is found that the inhomogeneous strength of backfill materials brings local deformation of the pipe.
- 17 July 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
Field Measurement and Numerical Analysis for Buried Large Diameter Steel Pipes
This paper presents an overview of field tests for buried pipe, which were conducted using steel pipes with 3500 mm diameter and 26 mm thickness. In this full-scale test, five kinds of construction site were employed. The depth of soil cover was approximately 3.0 m in every case. Sheet pile method was employed in Case-5, and open-cut method was conducted in the other cases. Displacement transducers were installed in the pipe and strain gauges were circumferentially attached to the inner of the pipe. The deformation of pipe was observed for over a year by those measures. Therefore, it is found that the behavior of the buried pipe was strongly influenced by backfilling methods. In addition, FEM analyses were conducted to confirm the behavior of soil-pipe interaction. Thus, it is found that the inhomogeneous strength of backfill materials brings local deformation of the pipe.
- 1 April 2008
- Published by Emerald Publishing in Geosynthetics International
- Vol. 15 (2) , 119-135
Shear strength and deformation characteristics of geosynthetic soil bags stacked horizontal and inclined
The strength of stacked soil bags is very low when sheared laterally, compared with the strength when compressed vertically. To substantially increase the stability of soil structures composed of stacked soil bags, this paper proposes inclined stacking of soil bags so that the compressive stress on the bag-to-bag interface increases. A series of lateral shear loading tests were performed on a pile of three full-scale soil bags stacked horizontally (δ = 0°) as well as inclined (δ = 18°) at different vertical confining pressures (30 kPa, 150 kPa and 300 kPa). Two types of backfill material were used: a poorly graded fine sand and a well-graded sandy gravel. The shear strength of the soil bags was considerably larger when stacked inclined than when stacked horizontally. With soil bags of sandy gravel, whether stacked horizontally or inclined, failure was dominantly always by slippage along the bag-to-bag interface. With soil bags of Toyoura sand, when stacked inclined at high confining pressure, failure was induced by shear failure in the backfill. It is shown that the method of inclined stacking method at a suitable angle is simple and cost-effective. It is also important to compact soil bags in advance, and to use well-graded coarse backfill to increase the interface friction angle, the strength of the backfill and the confining pressure in the backfill. The strength of stacked soil bags is very low when sheared laterally, compared with the strength when compressed vertically. To substantially increase the stability of soil structures composed of stacked soil bags, this paper proposes inclined stacking of soil bags so that the compressive stress on the bag-to-bag interface increases. A series of lateral shear loading tests were performed on a pile of three full-scale soil bags stacked horizontally (δ = 0°) as well as inclined (δ = 18°) at different vertical confining pressures (30 kPa, 150 kPa and 300 kPa). Two types of backfill material were used: a poorly graded fine sand and a well-graded sandy gravel. The shear strength of the soil bags was considerably larger when stacked inclined than when stacked horizontally. With soil bags of sandy gravel, whether stacked horizontally or inclined, failure was dominantly always by slippage along the bag-to-bag interface. With soil bags of Toyoura sand, when stacked inclined at high confining pressure, failure was induced by shear failure in the backfill. It is shown that the method of inclined stacking method at a suitable angle is simple and cost-effective. It is also important to compact soil bags in advance, and to use well-graded coarse backfill to increase the interface friction angle, the strength of the backfill and the confining pressure in the backfill.
- 1 April 2008
- Published by Emerald Publishing in Geosynthetics International
- Vol. 15 (2) , 119-135
Shear strength and deformation characteristics of geosynthetic soil bags stacked horizontal and inclined
The strength of stacked soil bags is very low when sheared laterally, compared with the strength when compressed vertically. To substantially increase the stability of soil structures composed of stacked soil bags, this paper proposes inclined stacking of soil bags so that the compressive stress on the bag-to-bag interface increases. A series of lateral shear loading tests were performed on a pile of three full-scale soil bags stacked horizontally (δ = 0°) as well as inclined (δ = 18°) at different vertical confining pressures (30 kPa, 150 kPa and 300 kPa). Two types of backfill material were used: a poorly graded fine sand and a well-graded sandy gravel. The shear strength of the soil bags was considerably larger when stacked inclined than when stacked horizontally. With soil bags of sandy gravel, whether stacked horizontally or inclined, failure was dominantly always by slippage along the bag-to-bag interface. With soil bags of Toyoura sand, when stacked inclined at high confining pressure, failure was induced by shear failure in the backfill. It is shown that the method of inclined stacking method at a suitable angle is simple and cost-effective. It is also important to compact soil bags in advance, and to use well-graded coarse backfill to increase the interface friction angle, the strength of the backfill and the confining pressure in the backfill. The strength of stacked soil bags is very low when sheared laterally, compared with the strength when compressed vertically. To substantially increase the stability of soil structures composed of stacked soil bags, this paper proposes inclined stacking of soil bags so that the compressive stress on the bag-to-bag interface increases. A series of lateral shear loading tests were performed on a pile of three full-scale soil bags stacked horizontally (δ = 0°) as well as inclined (δ = 18°) at different vertical confining pressures (30 kPa, 150 kPa and 300 kPa). Two types of backfill material were used: a poorly graded fine sand and a well-graded sandy gravel. The shear strength of the soil bags was considerably larger when stacked inclined than when stacked horizontally. With soil bags of sandy gravel, whether stacked horizontally or inclined, failure was dominantly always by slippage along the bag-to-bag interface. With soil bags of Toyoura sand, when stacked inclined at high confining pressure, failure was induced by shear failure in the backfill. It is shown that the method of inclined stacking method at a suitable angle is simple and cost-effective. It is also important to compact soil bags in advance, and to use well-graded coarse backfill to increase the interface friction angle, the strength of the backfill and the confining pressure in the backfill.