Daniel Rademacher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Daniel Rademacher has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Michael Vergöhl
8 shared publications- Stefan Bruns
Department of Optical and Electrical Coatings, Fraunhofer Institute for Surface Engineering and Thin Films IST, 38108 Braunschweig, Germany
3 shared publications Benjamin Fritz
Fraunhofer Institute for Surface Engineering and Thin Films IST, Bienroder Weg 54 E, Braunschweig 38108, Germany
2 shared publicationsGünter Bräuer
2 shared publicationsPeter Weiss
1 shared publicationPeter Weiss
1 shared publication
Latest Publications
- 21 January 2014
- Published by Optica Publishing Group in Applied Optics
- Vol. 53 (4)
Properties of reactive sputtered alumina–silica mixtures
- 21 January 2014
- Published by Optica Publishing Group in Applied Optics
- Vol. 53 (4)
Properties of reactive sputtered alumina–silica mixtures
- 9 December 2012
- Published by Elsevier in Thin Solid Films
- Vol. 532, 98-105
Sputtering of dielectric single layers by metallic mode reactive sputtering and conventional reactive sputtering from cylindrical cathodes in a sputter-up configuration
- 9 December 2012
- Published by Elsevier in Thin Solid Films
- Vol. 532, 98-105
Sputtering of dielectric single layers by metallic mode reactive sputtering and conventional reactive sputtering from cylindrical cathodes in a sputter-up configuration
- 20 November 2012
- Published by Optica Publishing Group in Applied Optics
- Vol. 51 (33) , 8047-8051
Optical properties of silicon titanium oxide mixtures prepared by metallic mode reactive sputtering
In this paper different mixtures are prepared by metallic mode reactive sputtering. The samples were sputtered from cylindrical targets in a sputter-up configuration using an additional plasma source for oxidization. The different ratios of and in the mixtures are prepared by a target sputtering power variation. Optical film properties of the mixtures such as refractive index, which is determined by ellipsometric measurements, and optical bandgap, which is measured by photometric (transmission) measurements, are investigated. The thin-film structure is investigated by x-ray diffraction analysis and the stress of the films is presented. It is shown that the metallic mode reactive sputtering in the present configuration is applicable to continuously tune optical and mechanical properties. Finally the sputtered mixed materials are compared with other optical standard materials such as , , , and .- 20 November 2012
- Published by Optica Publishing Group in Applied Optics
- Vol. 51 (33) , 8047-8051
Optical properties of silicon titanium oxide mixtures prepared by metallic mode reactive sputtering
In this paper different mixtures are prepared by metallic mode reactive sputtering. The samples were sputtered from cylindrical targets in a sputter-up configuration using an additional plasma source for oxidization. The different ratios of and in the mixtures are prepared by a target sputtering power variation. Optical film properties of the mixtures such as refractive index, which is determined by ellipsometric measurements, and optical bandgap, which is measured by photometric (transmission) measurements, are investigated. The thin-film structure is investigated by x-ray diffraction analysis and the stress of the films is presented. It is shown that the metallic mode reactive sputtering in the present configuration is applicable to continuously tune optical and mechanical properties. Finally the sputtered mixed materials are compared with other optical standard materials such as , , , and .- 28 February 2012
- Published by Optica Publishing Group in Applied Optics
- Vol. 51 (7) , 927-935
Origin of particles during reactive sputtering of oxides using planar and cylindrical magnetrons
Particles generated during reactive magnetron sputtering cause defects in optical thin films, which may lead to losses in optical performance, pinholes, loss of adhesion, decreased laser-induced damage thresholds and many more negative effects. Therefore, it is important to reduce the particle contamination during the manufacturing process. In the present paper, the origin of particles during the deposition of various oxide films by midfrequency pulsed reactive magnetron sputtering was investigated. Several steps have been undertaken to decrease the particle contamination during the complete substrate handling procedure. It was found that conditioning of the vacuum chamber can help to decrease the defect level significantly. This level remains low for several hours of sputtering and increases after 100 hours of process time. Particle densities of films deposited with cylindrical and planar dual magnetrons at different process parameters as well as different positions underneath the target were compared. It was observed that the process power influences the particle density significantly in case of planar targets while cylindrical targets have no such strong dependence. In addition, the particle contamination caused by different cylindrical target materials was analyzed. No major differences in particle contamination of different cylindrical target types and materials were found.- 28 February 2012
- Published by Optica Publishing Group in Applied Optics
- Vol. 51 (7) , 927-935
Origin of particles during reactive sputtering of oxides using planar and cylindrical magnetrons
Particles generated during reactive magnetron sputtering cause defects in optical thin films, which may lead to losses in optical performance, pinholes, loss of adhesion, decreased laser-induced damage thresholds and many more negative effects. Therefore, it is important to reduce the particle contamination during the manufacturing process. In the present paper, the origin of particles during the deposition of various oxide films by midfrequency pulsed reactive magnetron sputtering was investigated. Several steps have been undertaken to decrease the particle contamination during the complete substrate handling procedure. It was found that conditioning of the vacuum chamber can help to decrease the defect level significantly. This level remains low for several hours of sputtering and increases after 100 hours of process time. Particle densities of films deposited with cylindrical and planar dual magnetrons at different process parameters as well as different positions underneath the target were compared. It was observed that the process power influences the particle density significantly in case of planar targets while cylindrical targets have no such strong dependence. In addition, the particle contamination caused by different cylindrical target materials was analyzed. No major differences in particle contamination of different cylindrical target types and materials were found.- 20 December 2010
- Published by Optica Publishing Group in Applied Optics
- Vol. 50 (9) , C222-C227
In situ thickness determination of multilayered structures using single wavelength ellipsometry and reverse engineering.
An in situ monitoring setup and process control loop were developed and integrated into a magnetron sputtering coater equipped with a Sentech SE 401 single wavelength ellipsometer, including the engineering of software for in situ process control to enhance production accuracy. By using that software, the system allows direct monitoring of the layer thickness on a moving substrate. It is shown that it is possible to determine the complex index of refraction from the distribution of measurements depending on the layer thickness. A strategy has been developed for in situ reverse thickness engineering of the top layers to compensate measurement errors.
- 20 December 2010
- Published by Optica Publishing Group in Applied Optics
- Vol. 50 (9) , C222-C227
In situ thickness determination of multilayered structures using single wavelength ellipsometry and reverse engineering.
An in situ monitoring setup and process control loop were developed and integrated into a magnetron sputtering coater equipped with a Sentech SE 401 single wavelength ellipsometer, including the engineering of software for in situ process control to enhance production accuracy. By using that software, the system allows direct monitoring of the layer thickness on a moving substrate. It is shown that it is possible to determine the complex index of refraction from the distribution of measurements depending on the layer thickness. A strategy has been developed for in situ reverse thickness engineering of the top layers to compensate measurement errors.
- 1 January 2010
- Published by Optica Publishing Group
Particle generation during reactive magnetron sputtering of SiO2 with cylindrical and planar cathodes
SiO2layers were deposited by pulsed reactive magnetron sputtering with cylindrical and planar dual magnetrons. The particle density in SiO2films deposited at different process parameters is analyzed.
- 1 January 2010
- Published by Optica Publishing Group
Particle generation during reactive magnetron sputtering of SiO2 with cylindrical and planar cathodes
SiO2layers were deposited by pulsed reactive magnetron sputtering with cylindrical and planar dual magnetrons. The particle density in SiO2films deposited at different process parameters is analyzed.