HKHakan Karslı

Hakan Karslı

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hakan Karslı has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    TÜNEL YAPILARINDA KARŞILAŞILAN MÜHENDİSLİK PROBLEMLERİNİN JEOFİZİK YÖNTEMLERLE BELİRLENMESİ: BURSA İLİ DOĞANCI TÜNELİ ÖRNEĞİ

    by Mustafa Kirici, Hakan Karslı

    Tüm dünyada karayolu tünellerin yapımı sırasında ve sonrasında, jeolojik koşullardan kaynaklı pek çok mühendislik problemi ile karşılaşılmaktadır. Bu çalışmada, Bursa İli Osmangazi-Orhangazi ilçeleri bağlantı karayolundaki Doğancı Tüneli'nin yan ve tavan duvarlarından su sızıntılarının ve ilişkili oluşan deformasyonların belirlenmesinde, üç farklı jeofizik yöntemin sağladığı katkılar incelenmiştir. Bu kapsamda, tünelin iç duvarlarında Yer Radarı (YR), Elektrik Özdirenç Tomografi (EÖT) ve Çok Kanallı Yüzey Dalgası Analizi (ÇKYDA), tünelin girişinde üst kotta ve çıkışındaki palye üstünde sadece EÖT ölçümleri yapılmıştır. Özdirenç değerleri 4-1000 Ohm.m ve S-dalga hızı değerleri 280-800 m/s arasında elde edilmiştir. Birbirine paralel YR profillerinden tünelin duvarlarının ve dış cephesinin üç boyutlu görüntüleri oluşturulmuştur. Tüm bulgular birlikte değerlendirildiğinde, genel olarak özdirencin ve S-dalga hızının düşük, YR genliklerinin ise görece yüksek olduğu tünel bölümleri su sızıntılarından kaynaklı deformasyonlarla ilişkilendirilmiştir. Sonuç olarak, birkaç jeofizik yöntemin birlikte kullanılmasının tünellerde gözlenen deformasyonların kaynağının belirlenmesinde son derece yararlı olduğu görülmüştür.

  • Open Access

    Determination of Rippability Classes Through Classical and Geophysical Methods in New Forest Road Excavations, and Their Evaluation in Terms of Cost and Progress Payments

    by Nur Diktaş-Bulut, Selçuk Gümüş, Hakan Karslı, Tuğba Bozlar, Hafiz Hulusi Acar

    Accurately determining soil classes in forest road constructions holds paramount importance in mitigating inconsistencies and disputes in cost and progress payments during and after construction. This study aims to explore the potential of geophysical methods (seismic refraction tomography – SRT, active multichannel analysis of surface waves – A-MASW, electrical resistivity tomography – ERT, and ground-penetrating radar-GPR) in determining the rippability classifications of geological units to be excavated in new forest road constructions, as well as vertical stratification and lateral lithological facies boundaries. This study also conducts a comparative analysis between the cost and progress payment values obtained through classical methods. The study area encompasses six new forest road alignments identified within the Trabzon Regional Directorate of Forestry investment program in Türkiye. For assessing the reliability and validity of the measurements, the Cronbach's alpha test was employed. The equality of the measured variable variances across groups was determined using the Levene's test, and to determine the source of differences among groups subsequent to the measurements, the Dunnett's test from multiple comparison tests was utilized. The study revealed disparities between the excavation volumes/class ratios/approximate costs calculated based on soil classes in new forest roads by the forestry administration, the excavation volumes/class ratios/approximate costs realized upon construction completion, and the excavation volumes/class ratios/approximate costs calculated within the scope of this study. The results obtained demonstrated that the combined utilization of SRT, ERT, and A-MASW methods enhanced the reliability of soil characterization and rippability classification when determining rock rippability characteristics in forest road constructions. In this context, it is considered that the additional cost incurred by geophysical engineering measurements can be justifiably met, given the potential benefits, which include more rational planning of investment budgets and cost analyses in new forest road constructions, as well as the facilitation of savings in time, labor, and capital. Furthermore, these measurements are anticipated to contribute to the resolution of potential disagreements between contractors and forestry administrations.


  • Open Access

    Subsurface characterization by active and passive source geophysical methods after the 06 February 2023 earthquakes in Turkey

    by Hakan Karslı, Ali Erden Babacan, Özgenç Akın

    Two large earthquakes (Mw = 7.7 and Mw = 7.6) that occurred in Turkey on February 6, 2023, affected a very extent region and caused a lot of loss of life and property. This paper presents preliminary results from geophysical measurements (Seismic Refraction Tomography-SRT, Multi-Channel Surface Wave Analysis-MASW and Microtremor-MT) on eight profiles in four provinces (Kahramanmaraş, Hatay, Malatya, Gaziantep) to understand the relationship between subsurface properties and the destruction that occurs immediately after earthquakes. By analyzing the geophysical data, the dynamic-elastic properties of ground and the soil classification according to Vs30 were determined. It is generally understood that the near-surface (< ~ 10–15 m) units in the measurement areas are very loose, and the deeper ones (≥ ~ 15–20 m) have a very porous/fractured structure. Soil classes were defined as ZD (Malatya-1, Hatay-1 and Kahramanmaraş-1) and ZC (Malatya-2, Hatay-2, Gaziantep-1,2 and Kahramanmaraş-2). In addition, by evaluating the information of strong ground motion station closest to the measurement profiles, it is observed that the PGA values versus epicenter distances are higher at stations in the zone parallel to the direction of both faults than those in the perpendicular zones. This leads directivity effect in the propagation of earthquake waves. The results indicate that one of the basic reasons for the damages is that the earthquake-ground-structure relationship has not been fully and accurately reflected in building designs. Therefore, future researches involving more geophysical data and PGA values will provide more information about the structural, physical and geotechnical properties of subsurface and definitive results.


  • Open Access

    An assessment of seismicity and near surface geophysical characteristics of potential solid waste landfill sites in the Eastern Black Sea Region of Türkiye

    by Hakan Karslı, Ali Erden Babacan, Nilgün Sayıl, Kaan Hakan Çoban, Özgenç Akın

    This study aimed to assess the suitability of the potential solid waste landfill sites in seven provinces (Samsun, Ordu, Giresun, Trabzon, Gümüşhane, Bayburt and Artvin) in the Eastern Blacksea Region of Türkiye. The earthquake hazard analysis for two major earthquakes which occurred in the region was first carried out. Then, the geophysical methods including seismic refraction tomography (SRT), electrical resistivity tomography (ERT) and Multichannel Analysis of Surface Waves (MASW) were conducted to find out the structural and physical properties of the subsurface which include the layering, soil classification based on VS30 and the groundwater content at 25 locations of 13 in target provinces. The integrated interpretation of whole data sets demonstrates that Işıktepe, Esence, Çamburnu and Kazantaş which are characterized by VP > 1200 m/s, VS30 ≥ 400 m/s, ρ > 70 Ohm-m, low earthquake hazard and seismicity are more suitable among others. Vezirköprü, Şebinkarahisar, Yenice, Bayburt-Center, Balkaynak and Murgul will be suitable after a geotechnical reclamation due to moderate seismic velocities and electrical resistivity which are 900 < VP ≤ 1200 m/s, 200 < VS30 < 400 m/s and 10 < ρ ≤ 70 Ohm-m representing stiff and wet soils. In addition, Bafra, Ağalık and Ovacık were considered to be unsuitable due to the presence of thick, water-saturated soft soil and extremely weathered rocks. Finally, this study shows that the joint interpretation of seismicity and geophysical data in potential waste landfill sites, extremely important for the planning and development of a city, can provide the valuable information which will enable to prevent possible deformations, environmental problems and economic losses after waste landfill.


  • AKTİF ÇOK KANALLI YÜZEY DALGASI ANALİZİ (A-ÇKYDA)YÖNTEMİNDE VERİ TOPLAMA VE TABAKA PARAMETRELERİNİN TEMEL MOD DİSPERSİYON EĞRİSİ ÜZERİNDEKİ ETKİLERİ

    by Hakan Karsli, Mustafa Şenkaya

    Aktif ÇKYDA yönteminde, sığ yeraltının güvenilir bir S-dalgası hız-derinlik profilini elde etmek için en önemli aşamalarından biri, geniş frekans aralığında sürekli ve yüksek ayrımlı bir dispersiyon eğrisinin elde edilmesidir. Bu makalede, tabaka (S- ve P-dalga hızları, yoğunluk ve kalınlık) ve veri toplama (kaynak ofseti-X0, alıcı aralığı-dx ve sayısı-N, serim boyu-L=(N-1)*dx) parametrelerinin, yüzey dalga alanının temel mod dispersiyon eğrisi üzerindeki etkileri, yapay atış verilerinin analizi ile incelenmiştir. Yapay veriler, tabaka yansıma/iletim katsayısı tekniği ile hesaplanan dispersiyon eğrisi kullanılarak, her bir alıcıda harmonik mod toplama tekniği ile oluşturulmuştur. Buna göre, düşük S-dalga hızlı ara tabakalar dispersiyon eğrisinin düşük frekans bölgesinde düşük hızlara kaymasına, yüksek hızlı ara tabakalar ise, dispersiyon eğrisinin yüksek frekanslarda sürekliliğinin bozulmasına (zig-zag etkisi) ve yüksek mod etkisi yanılgısına neden olabileceği gözlenmiştir. Kaynak ofseti yüzey dalgalarının tam dalga formlarının oluşmasında etkin iken, ilk ve son alıcı arası uzaklık olan serim uzunluğunun ise, dispersiyon eğrisinin frekans bandını ve çözünürlüğünü etkilediği görülmüştür. Ayrıca, geniş alıcı aralıklarının, dispersiyon eğrisinin düşük frekans bölgesindeki güvenirliğinin arttırmasının yanında, yüksek frekans bölgesinde dalga sayısı katlanması nedeniyle dispersiyon eğrisinin sürekliliğini bozduğu görülmüştür. Sonuç olarak, farklı dalga hızlarına sahip yer modelleri için üretilen yapay veriler üzerinde yapılan analizler N

  • Combining ground-penetrating radar sections with different antenna frequencies including time-frequency domain noise suppression filters

    by Hilal Alemdağ, Aysel Şeren, Hakan Karslı

    Ground-penetrating radar (GPR) is one of the most useful geophysical methods that rapidly and efficiently provide high-resolution subsurface images depending on antenna frequencies and target depth. Recently, to enrich the interpretation of GPR sections, multifrequency sections have been combined at deeper and shallower levels in a profile. In this context, the techniques of combination and image quality improving processes of GPR data also have gained importance. For this, simple summation (SS) and time-shifted balanced summation (TSBS) techniques, frequency-domain local mean notch filter (FDLMNF), frequency-space (f-x) filter, and automatic gain control (AGC) processes are sequentially applied within a workflow. Although the FDLMNF is used to effectively remove single-frequency spike-like noises without distortion around the notch frequency, the f-x filter is applied to suppress the random noise and improve the lateral traceability of the section, and AGC provides a statistically based gain recovery. In the proposed workflow, after generating synthetic and field GPR data with 100 and 250 MHz frequencies, data were combined using SS and TSBS techniques. Finally, FDLMNF, f-x, and AGC were applied to increase the image quality of this combined section. The result sections were evaluated and compared using the Fourier average amplitude and f-k spectra. According to the spectra, the TSBS technique provides good spectral balancing and offers wider spectral content. At the same time, it was observed that the image quality of the combined GPR sections increased significantly after applying FDLMNF, f-x, and AGC processes. As a result, when the sections resulting from SS and TSBS techniques are examined, the image enhancement processes that protect and strengthen the spectral bandwidth of the data are successful. Thus, the temporal resolution and spatial continuity of GPR sections also will be increased, and a better quality interpretation will be provided.


  • SİSMİK KIRILMA VERİLERİNDE JEOFON MERKEZ FREKANSININ İLK VARIŞ ZAMANLARI ÜZERİNDEKİ ETKİSİNİN İNCELENMESİ

    by Mustafa Şenkaya, Hakan Karsli

    Ülkemizde, arazide gerçekleştirilen ya da kamu kurumlarınca kontrol edilen Jeofizik çalışmalarda çok kanallı yüzey dalgası ölçümü için genellikle 4.5Hz’ lik düşey bileşen jeofonlar kullanılmaktadır. Ancak, bazı kamu kurumları 4.5Hz düşey jeofonlarla, ilk varışların belirlenmesi amacıyla sismik kırılma çalışmaları yapılmasına izin vermemekte ve ilk varışların bu jeofonlarla elde edilen sismik kırılma verilerinden güvenilir şekilde okunamayacağını düşünmektedir. Bu çalışma kapsamında, sismik kırılma verilerinde jeofon merkez frekansının ilk varışlar üzerindeki etkisi araştırılmıştır. Çalışmada, 4.5, 14 ve 40 Hz merkez frekanslı üç farklı düşey bileşen jeofon için hesaplanan sentetik sismik izler ve iki farklı sahada, farklı üreticilere ait sırasıyla 4.5-14 Hz, 4.5-40 Hz jeofon çiftleri ile toplanan gerçek sismik kırılma verileri kullanılmıştır. Sentetik ve tüm saha verileri üzerinde yapılan ilk varış analizleri açık şekilde göstermiştir ki, sismik kırılma verilerinden elde edilecek ilk varışlar, kullanılan jeofonların merkez frekanslarından bağımsızdır. Dolayısıyla, aynı saha parametreleri ile farklı merkez frekanslı jeofonlarla toplanan sismik kırılma verilerinin ilk varış zamanları değişiklik göstermemektedir. Bu tip veri setlerinde görülebilecek tek fark, kayıt edilen verinin genlik spektrumunda merkez frekans etrafındaki genliğin artması olacaktır, ancak bu durum ilk varış zamanlarını etkilememektedir. Sonuç olarak, sismik kırılma arazi çalışmalarında hem çok kanallı yüzey dalgası hem de geleneksel sismik kırılma verilerinin toplanmasında, farklı jeofon setlerinin lojistiğine ihtiyaç olmayıp, tek bir jeofon setinin (örneğin 4.5 Hz) yeterli olacağı bu çalışmayla gösterilmiştir.