Christopher J. Walsh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Christopher J. Walsh has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Achim J. Leistner
The authors are with the Division of Telecommunications and Industrial Physics, Commonwealth Scientific and Industrial Research Organisation (CSIRO), P.O. Box 218, Lindfield 2070, Australia
2 shared publicationsBozenko F. Oreb
The authors are with the Division of Telecommunications and Industrial Physics, Commonwealth Scientific and Industrial Research Organisation (CSIRO), P.O. Box 218, Lindfield 2070, Australia
2 shared publicationsDavid I. Farrant
The authors are with the Commonwealth Scientific and Industrial Research Organization, Division of Telecommunications and Industrial Physics, P.O. Box 218, Lindfield 2070, Australia
1 shared publicationJeffrey Seckold
The authors are with the Commonwealth Scientific and Industrial Research Organization, Division of Telecommunications and Industrial Physics, P.O. Box 218, Lindfield 2070, Australia
1 shared publication
Latest Publications
- 1 August 1999
- Published by Optica Publishing Group in Applied Optics
- Vol. 38 (22) , 4790-4801
Power spectral density analysis of optical substrates for gravitational-wave interferometry.
The power spectral density of surface-relief variations on polished optical surfaces across microscopic through to macroscopic spatial scales is calculated from measurements on substrates that are being produced for the Laser Interferometer Gravitational-Wave Observatory (LIGO). These spectra give a guide to the scattering properties of the surface, which in turn critically influence the performance of LIGO. Measurements obtained by use of a full-aperture interferometer and an interference microscope with two different objectives are combined to produce one-dimensional power spectral density representations of the surfaces across spatial frequencies ranging from 0.1 to 8000 cm-1. These measurements from different instruments are in good agreement with an analytic power spectrum that varies as ν -1.5, where ν is the spatial frequency. Some anomalies in the power spectral density spectra can be related to aspects of the polishing process.
- 1 August 1999
- Published by Optica Publishing Group in Applied Optics
- Vol. 38 (22) , 4790-4801
Power spectral density analysis of optical substrates for gravitational-wave interferometry.
The power spectral density of surface-relief variations on polished optical surfaces across microscopic through to macroscopic spatial scales is calculated from measurements on substrates that are being produced for the Laser Interferometer Gravitational-Wave Observatory (LIGO). These spectra give a guide to the scattering properties of the surface, which in turn critically influence the performance of LIGO. Measurements obtained by use of a full-aperture interferometer and an interference microscope with two different objectives are combined to produce one-dimensional power spectral density representations of the surfaces across spatial frequencies ranging from 0.1 to 8000 cm-1. These measurements from different instruments are in good agreement with an analytic power spectrum that varies as ν -1.5, where ν is the spatial frequency. Some anomalies in the power spectral density spectra can be related to aspects of the polishing process.
- 1 May 1999
- Published by Optica Publishing Group in Applied Optics
- Vol. 38 (13) , 2870-2879
Fabrication and measurement of optics for the laser interferometer gravitational wave observatory.
The manufacture and testing of high-precision optical surfaces for the Laser Interferometer Gravitational Wave Observatory is described. Through the use of carefully shaped polishing laps made of a nondeformable polymer material coated on a rigid base, surfaces 250 mm in diameter with radii of curvature between 7 and 15 km were polished to an accuracy of several hundred meters in the curvature and with low values of waviness and microroughness. Metrology instrumentation used to measure the optical finish included a large-aperture digital interferometer calibrated to nanometer-level accuracy for measurements of curvature, astigmatism, and waviness and an interference microscope for measurements of microroughness. The power spectra of the data from both instruments were in good agreement.
- 1 May 1999
- Published by Optica Publishing Group in Applied Optics
- Vol. 38 (13) , 2870-2879
Fabrication and measurement of optics for the laser interferometer gravitational wave observatory.
The manufacture and testing of high-precision optical surfaces for the Laser Interferometer Gravitational Wave Observatory is described. Through the use of carefully shaped polishing laps made of a nondeformable polymer material coated on a rigid base, surfaces 250 mm in diameter with radii of curvature between 7 and 15 km were polished to an accuracy of several hundred meters in the curvature and with low values of waviness and microroughness. Metrology instrumentation used to measure the optical finish included a large-aperture digital interferometer calibrated to nanometer-level accuracy for measurements of curvature, astigmatism, and waviness and an interference microscope for measurements of microroughness. The power spectra of the data from both instruments were in good agreement.