Chia‐Wei Chang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chia‐Wei Chang has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
Sheng‐Lyang Jang
Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
17 shared publicationsSheng-Lyang Jang
Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
10 shared publicationsMiin‐Horng Juang
Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
6 shared publicationsChing‐Wen Hsue
Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
4 shared publicationsChing-Wen Hsue
Department of Electronic Engineering, National Taiwan University of Science and Technology, 43, Keelung Road, Section 4, Taipei, Taiwan 106, Republic of China
3 shared publicationsJhin-Fang Huang
Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
3 shared publications
Latest Publications
- 27 February 2013
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (4) , 700-703
A fully‐integrated CMOS quadrature VCO implemented with balanced VCOs
A new CMOS quadrature voltage‐controlled oscillator (QVCO) is proposed. The LC‐tank QVCO consists of two balanced complementary Colpitts VCOs with differential outputs. The tail inductor output of the first balanced VCO is injected to the gate of the tail transistor in the second balanced VCO and vice versa to ensure the two balanced VCOs operate in quadrature. At the supply voltage of 1.2 V, the total power consumption is 4.32 mW. The free‐running frequency tuning range is 13.4%, tunable from 5.92 to 6.77 GHz as the tuning voltage is varied from 0 to 2 V. The QVCO has been implemented with the TSMC 0.18 μm CMOS technology and the die area is 0.843 × 1.024 mm2. The measured phase noise at 1 MHz offset is −121.67 dBc/Hz at the oscillation frequency of 6.74 GHz and the figure of merit of the proposed QVCO is about −191.89 dBc/Hz. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:700–703, 2013; View this article online at wileyonlinelibrary.com. DOI: 10.1002/mop.27433
- 27 February 2013
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (4) , 700-703
A fully‐integrated CMOS quadrature VCO implemented with balanced VCOs
A new CMOS quadrature voltage‐controlled oscillator (QVCO) is proposed. The LC‐tank QVCO consists of two balanced complementary Colpitts VCOs with differential outputs. The tail inductor output of the first balanced VCO is injected to the gate of the tail transistor in the second balanced VCO and vice versa to ensure the two balanced VCOs operate in quadrature. At the supply voltage of 1.2 V, the total power consumption is 4.32 mW. The free‐running frequency tuning range is 13.4%, tunable from 5.92 to 6.77 GHz as the tuning voltage is varied from 0 to 2 V. The QVCO has been implemented with the TSMC 0.18 μm CMOS technology and the die area is 0.843 × 1.024 mm2. The measured phase noise at 1 MHz offset is −121.67 dBc/Hz at the oscillation frequency of 6.74 GHz and the figure of merit of the proposed QVCO is about −191.89 dBc/Hz. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:700–703, 2013; View this article online at wileyonlinelibrary.com. DOI: 10.1002/mop.27433
- 27 February 2013
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (4) , 737-740
Triple‐band CMOS voltage‐controlled oscillator
A low‐phase noise triple‐band voltage‐controlled oscillator (VCO) is proposed and it consists of a triple‐resonance LC resonator and a cross‐coupled switching transistor pair. In the proposed VCO that uses the triple‐resonance LC‐resonator, band switching is achieved by tuning the varactors in the resonator without using lossy switches in the resonator path. The triple‐resonance LC resonator comprises a parallel‐tuned LC resonator and two series resonant resonators. The proposed VCO has been implemented with the TSMC 0.18 μm 1P6M CMOS technology and the core power consumption is 3.12 mW at the dc drain–source bias of 0.8 V. The VCO can generate differential signals in the frequency range of 6.651∼7.146 GHz, 5.607∼5.941 GHz, and 3.15 GHz∼3.483 GHz. The die area of the triple‐band VCO is 0.684 × 0.754 mm2. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:737–740, 2013; View this article online at wileyonlinelibrary.com. DOI: 10.1002/mop.27431
- 27 February 2013
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (4) , 737-740
Triple‐band CMOS voltage‐controlled oscillator
A low‐phase noise triple‐band voltage‐controlled oscillator (VCO) is proposed and it consists of a triple‐resonance LC resonator and a cross‐coupled switching transistor pair. In the proposed VCO that uses the triple‐resonance LC‐resonator, band switching is achieved by tuning the varactors in the resonator without using lossy switches in the resonator path. The triple‐resonance LC resonator comprises a parallel‐tuned LC resonator and two series resonant resonators. The proposed VCO has been implemented with the TSMC 0.18 μm 1P6M CMOS technology and the core power consumption is 3.12 mW at the dc drain–source bias of 0.8 V. The VCO can generate differential signals in the frequency range of 6.651∼7.146 GHz, 5.607∼5.941 GHz, and 3.15 GHz∼3.483 GHz. The die area of the triple‐band VCO is 0.684 × 0.754 mm2. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:737–740, 2013; View this article online at wileyonlinelibrary.com. DOI: 10.1002/mop.27431
- 28 January 2013
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (3) , 468-471
Dual‐band VCO with composite right‐/left‐handed resonator
This article proposes a high‐performance CMOS voltage‐controlled oscillator (VCO) implemented with composite right‐/left‐handed nonmobius‐connected LC‐rings to provide dual‐band differential outputs.The VCO consists of two cross‐coupled sub‐VCOs sharing series‐LC resonators. nMOSFET switches are used to control high‐ and low‐band outputs. The proposed VCO has been implemented with the TSMC 0.18 μm SiGe BiCMOS technology. The die area of the VCO is 1.16 × 1.12 mm2. With the switch on, the odd‐mode VCO operates at the high‐frequency 6 GHz band, and when the switch is off, the even‐mode VCO operates at the low‐frequency 4 GHz band. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 54:468–471, 2013; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.27375
- 28 January 2013
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (3) , 468-471
Dual‐band VCO with composite right‐/left‐handed resonator
This article proposes a high‐performance CMOS voltage‐controlled oscillator (VCO) implemented with composite right‐/left‐handed nonmobius‐connected LC‐rings to provide dual‐band differential outputs.The VCO consists of two cross‐coupled sub‐VCOs sharing series‐LC resonators. nMOSFET switches are used to control high‐ and low‐band outputs. The proposed VCO has been implemented with the TSMC 0.18 μm SiGe BiCMOS technology. The die area of the VCO is 1.16 × 1.12 mm2. With the switch on, the odd‐mode VCO operates at the high‐frequency 6 GHz band, and when the switch is off, the even‐mode VCO operates at the low‐frequency 4 GHz band. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 54:468–471, 2013; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.27375
- 28 January 2013
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (3) , 485-488
A dual-band cross-coupled oscillator using the varactor-switching mode technique
- 28 January 2013
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (3) , 485-488
A dual-band cross-coupled oscillator using the varactor-switching mode technique
- 21 December 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (2) , 310-313
CMOS quadrature VCO using a passive coupling device
This article presents a new fully‐integrated quadrature voltage‐controlled oscillator (QVCO), which consists of two differential VCOs coupled via an inductor‐ring. The proposed CMOS QVCO has been implemented with the TSMC 0.18‐μm CMOS technology and the die area is 0.693 × 0.976 mm2. At the supply voltage of 0.7 V, the total power consumption is 2.58 mW. The free‐running frequency of the QVCO is tunable from 5.15 to 5.55 GHz as the tuning voltage is varied from 0 to 0.7 V. The measured phase noise at 1 MHz frequency offset is −120.88 dBc/Hz at the oscillation frequency of 5.28 GHz and the figure of merit of the proposed QVCO is −191.21 dBc/Hz. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:310–313, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.27283
- 21 December 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (2) , 310-313
CMOS quadrature VCO using a passive coupling device
This article presents a new fully‐integrated quadrature voltage‐controlled oscillator (QVCO), which consists of two differential VCOs coupled via an inductor‐ring. The proposed CMOS QVCO has been implemented with the TSMC 0.18‐μm CMOS technology and the die area is 0.693 × 0.976 mm2. At the supply voltage of 0.7 V, the total power consumption is 2.58 mW. The free‐running frequency of the QVCO is tunable from 5.15 to 5.55 GHz as the tuning voltage is varied from 0 to 0.7 V. The measured phase noise at 1 MHz frequency offset is −120.88 dBc/Hz at the oscillation frequency of 5.28 GHz and the figure of merit of the proposed QVCO is −191.21 dBc/Hz. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:310–313, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.27283
- 21 December 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (2) , 266-269
An injection‐locked frequency quadrupler in 90 nm CMOS technology
On‐chip high‐frequency frequency sources suffer from quality (Q)‐factor degradation of varactors.Injection‐locked frequency multipliers allow the design of oscillators running at a frequency lower than required to take the advantage of higher Q‐factor varactor. This article proposes a fully integrated CMOS LC‐tank injection‐locked frequency quadrupler fabricated in the TSMC 90 nm RF‐CMOS process and describes the circuit design, operation principle, and measurement results of the quadrupler. The injection‐locked frequency quadrupler comprises a first‐harmonic injection‐locked oscillator with dual‐injection ports, two frequency doublers and a transformer balun. At the supply voltage of 0.7 V, the dc power consumption is 9.1 mW. At the incident power of 0 dBm, the injection‐locked frequency quadrupler can provide an output signal with the frequency from 24 to 29.6 GHz, while the frequency of the injection signal varies from 6 to 7.4 GHz. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:266–269, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.27291
- 21 December 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 55 (2) , 266-269
An injection‐locked frequency quadrupler in 90 nm CMOS technology
On‐chip high‐frequency frequency sources suffer from quality (Q)‐factor degradation of varactors.Injection‐locked frequency multipliers allow the design of oscillators running at a frequency lower than required to take the advantage of higher Q‐factor varactor. This article proposes a fully integrated CMOS LC‐tank injection‐locked frequency quadrupler fabricated in the TSMC 90 nm RF‐CMOS process and describes the circuit design, operation principle, and measurement results of the quadrupler. The injection‐locked frequency quadrupler comprises a first‐harmonic injection‐locked oscillator with dual‐injection ports, two frequency doublers and a transformer balun. At the supply voltage of 0.7 V, the dc power consumption is 9.1 mW. At the incident power of 0 dBm, the injection‐locked frequency quadrupler can provide an output signal with the frequency from 24 to 29.6 GHz, while the frequency of the injection signal varies from 6 to 7.4 GHz. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 55:266–269, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.27291
- 25 September 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 54 (12) , 2825-2828
A differential BiCMOS divide-by-4 injection-locked frequency divider
- 25 September 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 54 (12) , 2825-2828
A differential BiCMOS divide-by-4 injection-locked frequency divider
- 14 April 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 54 (7) , 1590-1593
A dual‐resonance CMOS voltage‐controlled oscillator with enhanced performance through new varactor topology
A new fully integrated, dual‐band CMOS voltage controlled oscillator (VCO) is presented. The VCO is composed of a p‐core cross‐coupled and an n‐core cross‐coupled Colpitts oscillator with dual‐resonance LC tank and was implemented in 90‐nm CMOS technology with 1.15 V supply voltage. The circuit allows the VCO to operate at two resonant frequencies with a common LC tank. This VCO is configured with 6.3 and 10 GHz frequency bands with differential outputs. The dual‐band VCO operates at 6.11–6.413 GHz and 9.72–10.24 GHz. The phase noises of the VCO operating at 9.72 and 6.4 GHz are −116.31 dBc/Hz and −122.79 dBc/Hz at 1‐MHz offset, respectively, while the VCO draws 4/4.28 mA and 4.6/4.92 mW consumption at high/low frequency band from a 1.15‐V supply. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 54:1590–1593, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.26882
- 14 April 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 54 (7) , 1590-1593
A dual‐resonance CMOS voltage‐controlled oscillator with enhanced performance through new varactor topology
A new fully integrated, dual‐band CMOS voltage controlled oscillator (VCO) is presented. The VCO is composed of a p‐core cross‐coupled and an n‐core cross‐coupled Colpitts oscillator with dual‐resonance LC tank and was implemented in 90‐nm CMOS technology with 1.15 V supply voltage. The circuit allows the VCO to operate at two resonant frequencies with a common LC tank. This VCO is configured with 6.3 and 10 GHz frequency bands with differential outputs. The dual‐band VCO operates at 6.11–6.413 GHz and 9.72–10.24 GHz. The phase noises of the VCO operating at 9.72 and 6.4 GHz are −116.31 dBc/Hz and −122.79 dBc/Hz at 1‐MHz offset, respectively, while the VCO draws 4/4.28 mA and 4.6/4.92 mW consumption at high/low frequency band from a 1.15‐V supply. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 54:1590–1593, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.26882
- 20 March 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 54 (6) , 1453-1455
CMOS transconductance‐enhanced Colpitts‐like quadrature voltage‐controlled oscillator
A new fully integrated CMOS quadrature voltage‐controlled oscillator (QVCO) is presented.The QVCO is composed of two cross‐coupled nMOSFETs in shunt with a parallel‐tuned LC resonator and was implemented in 0.18 μm CMOS technology. The source of nMOSFET is in series with a degenerated pMOSFET modulated by the VCO output signal. The negative resistance cell in the QVCO is a transconductance‐enhanced Colpitts‐like cell used to improve the start‐up oscillation. The QVCO is tunable from 7.04 to 8.08 GHz. Although the tuning voltage varies from 0 to 2 V. The phase noise of the QVCO operating at 7.09 GHz is −120.5 dBc/Hz at 1 MHz offset, while the QVCO draws 4 mA and uses 4 mW consumption. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 54:1453–1455, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.26820
- 20 March 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 54 (6) , 1453-1455
CMOS transconductance‐enhanced Colpitts‐like quadrature voltage‐controlled oscillator
A new fully integrated CMOS quadrature voltage‐controlled oscillator (QVCO) is presented.The QVCO is composed of two cross‐coupled nMOSFETs in shunt with a parallel‐tuned LC resonator and was implemented in 0.18 μm CMOS technology. The source of nMOSFET is in series with a degenerated pMOSFET modulated by the VCO output signal. The negative resistance cell in the QVCO is a transconductance‐enhanced Colpitts‐like cell used to improve the start‐up oscillation. The QVCO is tunable from 7.04 to 8.08 GHz. Although the tuning voltage varies from 0 to 2 V. The phase noise of the QVCO operating at 7.09 GHz is −120.5 dBc/Hz at 1 MHz offset, while the QVCO draws 4 mA and uses 4 mW consumption. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 54:1453–1455, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.26820
- 20 March 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 54 (6) , 1359-1362
Divide‐by‐4 injection‐locked frequency divider using two linear mixers
- 20 March 2012
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 54 (6) , 1359-1362
Divide‐by‐4 injection‐locked frequency divider using two linear mixers