GFGongkang Fu

Gongkang Fu

*This is an algorithmically generated author record based on publicly available information.

Gongkang Fu has a total of 21 co-authors. Here are the top co-authors by number of shared publications:

  • J. Feng

    Dept. of Civil and Environmental Engineering, Center for Advanced Bridge Engineering, Wayne State Univ., Detroit, MI 48202; and, Changjiang Scholar Chair Professor, Tongji Univ., Shanghai, China

    2 shared publications
  • Ji You

    Chair Professor, Guangdong Univ. of Technology, Guangzhou, China; Fuzhou Univ., Fuzhou, China; and Tongji Univ., Shanghai, China; and Professor and Chairman, Dept. of Civil, Architectural, and Environmental Engineering, Illinois Institute of Technology, Chicago, IL 60616; formerly Professor and Director, Center for Advanced Bridge Engineering, Dept. of Civil and Environmental Engineering, Wayne State Univ., Detroit, MI 48202

    2 shared publications
  • W. Dekelbab

    Dept. of Civil and Environmental Engineering, Center for Advanced Bridge Engineering, Wayne State Univ., Detroit, MI 48202; and, Changjiang Scholar Chair Professor, Tongji Univ., Shanghai, China

    2 shared publications
  • Asce Member

    1 shared publication
  • D. Mertz

    Dept. of Civil and Environmental Engineering, Center for Advanced Bridge Engineering, Wayne State Univ., Detroit, MI 48202; Changjiang Scholar Chair Professor, Tongji Univ., Shanghai, China

    1 shared publication
  • F. Moses

    Dept. of Civil and Environmental Engineering, Center for Advanced Bridge Engineering, Wayne State Univ., Detroit, MI 48202; Changjiang Scholar Chair Professor, Tongji Univ., Shanghai, China

    1 shared publication

Latest Publications

  • Extrapolation for Future Maximum Load Statistics

    by Gongkang Fu, Ji You

    The use of short-term load data to extrapolate or project remote future maximum load has been practiced in structural design code development and/or calibration. However, this approach has not been adequately evaluated or validated because of the absence of long-term data, which is important for the structures’ safety governed by these codes. In this paper, the application of such extrapolations to highway bridge design is studied by taking advantage of available long-term truck weight data obtained from the weigh-in-motion technique. A new extrapolation method is proposed from the understanding of the importance of the load probability distribution’s high tail. This approach significantly reduces the mathematical length of the extrapolation/projection and thus increases its reliability. Also presented in this paper are application examples. In addition, the extrapolation process proposed is evaluated with quantitative indexes. The application of a temporal extrapolation/projection can now be evaluated by...


  • Edge-Based Close-Range Digital Photogrammetry for Structural Deformation Measurement

    by Jian Ye, Gongkang Fu, Upendra P. Poudel

    This paper proposes a close-range digital photogrammetric system based on edge detection for structural deformation measurement. Different from traditional photogrammetric applications using discrete points, continuous edges in digital images are used here as the controlling feature in this new system. This makes it possible to acquire spatially intensive information. The system uses several digital images of the structure, taken from a number of different stations before and after the deformation is induced. Then, an image-matching algorithm based on the coplanarity condition developed here is applied to establish spatial relationships of the interested edges, identified by using a new high-precision method. These relationships are subsequently employed to acquire full-field deformation measurement of the structure. A series of experiments was conducted in the laboratory to investigate the capability of the new photogrammetric system. Results show that the system is highly accurate and suitable for struc...


  • Behavior of Reinforced Concrete Bridge Decks on Skewed Steel Superstructure under Truck Wheel Loads

    by Gongkang Fu, Yizhou Zhuang, Jihang Feng

    This paper focuses on the behavior of skewed concrete bridge decks on steel superstructure subjected to truck wheel loads. It was initiated to meet the need for investigating the role of truck loads in observed skewed deck cracking, which may interest bridge owners and engineers. Finite-element analysis was performed for typical skewed concrete decks, verified using in situ deck strain measurement during load testing of a bridge skewed at 49.1°. The analysis results show that service truck loads induce low strains/stresses in the decks, unlikely to initiate concrete cracking alone. Nevertheless, repeated truck wheel load application may cause cracks to become wider, longer, and more visible. The local effect of wheel load significantly contributes to the total strain/stress response, and the global effect may be negligible or significant, depending on the location. The current design approach estimates the local effect but ignores the global effect. It therefore does not model the situation satisfactorily. In addition, total strain/stress effects due to truck load increase slightly because of skew angle.


  • Planning for Commercial Vehicle Weight Limit Change: Application and Computer Software

    by G. Fu, Harry Cohen, Paul Thompson, J. Feng, W. Dekelbab

    Commercial vehicle weight limits here refer to those on the gross weight, axle spacing, and axle weights. They have a notable influence on the deterioration and lifespan of highway facilities such as pavements and bridges. A new methodology is presented here for estimating the monetary impact to a network of highway bridges due to commercial vehicle weight limit increase. This methodology focuses on four categories of cost impact: (1) life reduction due to fatigue of steel components; (2) life reduction due to fatigue of reinforced concrete decks; (3) requirements for addressing deficiency of existing bridges; and (4) capacity requirements for new bridges. For illustration, an application example of the new methodology is presented. The results show that Categories 3 and 4, additional inadequate bridges and increased requirements for new bridges, contribute more significantly to the total impact cost. In addition, a computer software program for the methodology has been developed and is introduced in this paper to facilitate implementation. It is intended to be used for highway planning at different network levels, such as for state, provincial, federal, or national jurisdictions.

  • Truck Loads and Bridge Capacity Evaluation in China

    by Gongkang Fu, Ji You

    Over the past 2–3 decades, the economic development in China has natured the establishment of a highway network with a large number of bridges. However, there are still no nationwide specification provisions for assessing their safe load carrying capacity. The research work reported herein focuses on developing reliability based requirements for this purpose. In this study, weigh-in-motion data for more than 7.3 million trucks were gathered from highways in three provinces of China, continuously over 1–16 months in 2006 and 2007. The data were processed and projected to model the live-load spectrum over 3-year and 100-year periods, respectively. The former is the required bridge inspection interval and the latter the bridge design life span, according to current Chinese maintenance and design specifications. The proposed projection method is shown to be more reliable compared with those reported. The resulting load spectra are used to assess the structural reliability of typical Chinese highway bridges at...


  • Impact of Commercial Vehicle Weight Change on Highway Bridge Infrastructure

    by G. Fu, J. Feng, W. Dekelbab, F. Moses, H. Cohen, D. Mertz

    Heavy trucks represent a major load to highway bridges in the transportation infrastructure system. These loads are directly related to the truck weight limits of the jurisdiction, and largely determine the standard loads for bridge design and evaluation. Thus, truck weight limit is one of the major factors affecting bridge deterioration and expenditure for maintenance, repair, and/or replacement. Truck weight in this paper not only refers to the truck gross weight but also to the axle weights and spacings that affect load effects. This paper presents the concepts of a new methodology for estimating cost effects of truck weight limit changes on bridges in a transportation infrastructure network. The methodology can serve as a tool for studying impacts of such changes. The resulting knowledge is needed when examining new truck weight limits, several of which have been and are still being debated at both the state and federal levels in the United States. The development of this estimation method has considered maximizing the use of available data (such as the bridge inventory) at the state infrastructure system level. In application examples completed (but not reported herein), the costs for relatively inadequate strength of existing bridges and for increased design requirement for new bridges were found dominant in the total impact cost.


  • Shake table model testing and its application

    by Xilin Lu, Gongkang Fu, Weixing Shi, Wensheng Lu

    This paper presents a study of shake table testing for aseismic design of structure systems. Two reinforced concrete structure models of different scales were used first to implement and demonstrate the similitude concept using available testing equipment. This concept was then applied to a 33‐story reinforced concrete building's scaled model, using multidirectional simulated seismic excitations. The test results were used to evaluate and modify the original design. Some of these results were also verified using field testing after the building's construction was completed. Comparison of the results between the model test and the full‐scale test shows that testing based on dynamic similitude using shake table are useful although not perfect and can provide supplementary data for decision making in engineering design. Copyright © 2007 John Wiley & Sons, Ltd.


  • Locality of Truck Loads and Adequacy of Bridge Design Load

    by John W. van de Lindt, Gongkang Fu, Yingmin Zhou, Reynaldo M. Pablo

    United States highway bridge design has advanced into the era of risk-based practice, milestoned by the American Association of State Highway and Transportation Officials Load and Resistance Factor Design Bridge Design Specifications. On the other hand, national and state design codes cannot specifically account for localized risk for each bridge site, which may have significantly different loading conditions from the national average. This issue is focused on here, as related to the adequacy of current bridge design loads for sites in the state of Michigan. The structural reliability indices are calculated for a randomly selected sample of new bridges from the Michigan inventory, including four major girder bridge types. Weigh-in-motion truck load data collected in Michigan are used to statistically characterize the truck load effect in the bridges’ primary members for moment and shear at critical cross sections. The reliability indices are found to vary significantly among the bridge sites and types investigated. Many of them indicate inadequate design load for the Detroit area.


  • Multimodal Simulation Method for System Reliability Analysis

    by Gongkang Fu, Fred Moses, Member Gongkang Fu, Asce Member

    In system reliability analysis, it is frequently necessary to resort to Monte Carlo simulation (MCS). The importance sampling method (ISM) is an advanced MCS method that may greatly improve the efficiency and accuracy of simulation approaches. Its application to structural system reliability analysis is focused here. Importance of proper determination of the sampling density is emphasized based on a critical review of other suggested sampling densities. A new sampling density, the weighted general normal sampling density (WGNSD), is proposed. This density is proportional to the ideally optimal one at the most important points of the variable space, and it is general for structural system reliability analysis. A variety of applications of this method are presented for illustration, as well as for demonstration of success with the proposed sampling density, including nondifferentiable failure surfaces and higher‐dimensional problems.