Dimitris Korakakis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Dimitris Korakakis has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Lee E Rodak
West Virginia University, Lane Dept. of Computer Science and Electrical Engineering, PO Box 6109, Morgantown, West Virginia, 26506, United States
7 shared publications - A. Kabulski
West Virginia University, Lane Department of Computer Science and Electrical Engineering, Morgantown, West Virginia, United States
5 shared publications - Ronak Rahimi
West Virginia University, Lane Department of Computer Science and Electrical Engineering, Morgantown, West Virginia, United States
4 shared publications - V. R. Pagán
West Virginia University, Lane Department of Computer Science and Electrical Engineering, Morgantown, West Virginia, United States
4 shared publications - Jeremy Dawson
West Virginia University
3 shared publications - Kalyan Reddy Kasarla
West Virginia University, Lane Department of Computer Science and Electrical Engineering, Morgantown, West Virginia, United States
3 shared publications
Latest Publications
- 16 January 2013
- Published by Springer Nature in MRS Proceedings
- Vol. 1519
High Harmonic Surface Acoustic Wave Devices for Harsh Environment Sensor Applications
- 16 January 2013
- Published by Springer Nature in MRS Proceedings
- Vol. 1519
High Harmonic Surface Acoustic Wave Devices for Harsh Environment Sensor Applications
- 20 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 59 (8) , 1806-1811
Harmonic surface acoustic waves on gallium nitride thin films
SAW devices operating at the fundamental frequency and the 5th, 7th, 9th, and 11th harmonics have been designed, fabricated, and measured. Devices were fabricated on GaN thin films on sapphire substrates, which were grown via metal organic vapor phase epitaxy (MOVPE). Operating frequencies of 230, 962, 1338, 1720, and 2100 MHz were achieved with devices that had a fundamental wavelength, /spl lambda/0 = 20 /spl mu/m. Gigahertz operation is realized with relatively large interdigital transducers that do not require complicated submicrometer fabrication techniques. SAW devices fabricated on the GaN/sapphire bilayer have an anisotropic propagation when the wavelength is longer than the GaN film thickness. It is shown that for GaN thin films, where khGaN > 10 (k = 2/spl pi///spl lambda/ and hGaN = GaN film thickness), effects of the substrate on the SAW propagation are eliminated. Bulk mode suppression at harmonic operation is also demonstrated.
- 20 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 59 (8) , 1806-1811
Harmonic surface acoustic waves on gallium nitride thin films
SAW devices operating at the fundamental frequency and the 5th, 7th, 9th, and 11th harmonics have been designed, fabricated, and measured. Devices were fabricated on GaN thin films on sapphire substrates, which were grown via metal organic vapor phase epitaxy (MOVPE). Operating frequencies of 230, 962, 1338, 1720, and 2100 MHz were achieved with devices that had a fundamental wavelength, /spl lambda/0 = 20 /spl mu/m. Gigahertz operation is realized with relatively large interdigital transducers that do not require complicated submicrometer fabrication techniques. SAW devices fabricated on the GaN/sapphire bilayer have an anisotropic propagation when the wavelength is longer than the GaN film thickness. It is shown that for GaN thin films, where khGaN > 10 (k = 2/spl pi///spl lambda/ and hGaN = GaN film thickness), effects of the substrate on the SAW propagation are eliminated. Bulk mode suppression at harmonic operation is also demonstrated.
- 16 February 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 24 (9) , 778-780
Surface Loading Sensitivity Characterization of a Resonant Planar Optical Waveguide Stack
Detuning of a coupled planar waveguide pair through surface loading of the top waveguide that is in contact with the analyte serves as a transducer for a Stacked Planar Affinity-Regulated Resonant Optical Waveguide (SPARROW) sensor. Here we investigate the surface loading detection sensitivity of a SPARROW transducer composed of a stack of two planar alumina waveguides grown using ion beam assisted e-beam deposition. Using a sucrose analyte solution introduced to the stack surface in a poly-di-methyl-siloxane (PDMS) microfluidic channel, the change in optical output power through the coupled waveguide pair as a function of sucrose analyte solution concentration was experimentally determined. Based on the analyte in the evanescent field penetration depth volume, the effective minimum detectable surface loading of the stack was determined to be 20 with a bulk index sensitivity of 5.6 refractive index units (RIU) for this stack configuration and experimental setup.
- 16 February 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 24 (9) , 778-780
Surface Loading Sensitivity Characterization of a Resonant Planar Optical Waveguide Stack
Detuning of a coupled planar waveguide pair through surface loading of the top waveguide that is in contact with the analyte serves as a transducer for a Stacked Planar Affinity-Regulated Resonant Optical Waveguide (SPARROW) sensor. Here we investigate the surface loading detection sensitivity of a SPARROW transducer composed of a stack of two planar alumina waveguides grown using ion beam assisted e-beam deposition. Using a sucrose analyte solution introduced to the stack surface in a poly-di-methyl-siloxane (PDMS) microfluidic channel, the change in optical output power through the coupled waveguide pair as a function of sucrose analyte solution concentration was experimentally determined. Based on the analyte in the evanescent field penetration depth volume, the effective minimum detectable surface loading of the stack was determined to be 20 with a bulk index sensitivity of 5.6 refractive index units (RIU) for this stack configuration and experimental setup.
- 1 July 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 110 (1) , 013702
Transport mechanism in ambipolar pentacene organic thin film transistors with lithium fluoride gate dielectric
The electrical properties of organic thin film transistors (OTFTs) based on pentacene as the active layer and lithium fluoride (LiF) as the gate dielectric layer were investigated. Fabricateddevices exhibited ambipolar behavior that can be controlled by the applied source, drain and gate biases. It was found that at low source-drain biases, multistep hopping is the dominant conduction mechanism, whereas in high voltage regimes, I-V data fits in the Fowler-Nordheim(FN)tunneling model. The relationship between the applied gate bias and the field enhancement factor, which is the ratio of the local surface electric field to the applied electric field, were determined from the slope of the FN plots. The dependency between the transition points in conduction mechanism upon gate bias has also been extracted from the FN plots. The transition points show more dependency on gate voltage for negative biases compared to the positive biases.
- 1 July 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 110 (1) , 013702
Transport mechanism in ambipolar pentacene organic thin film transistors with lithium fluoride gate dielectric
The electrical properties of organic thin film transistors (OTFTs) based on pentacene as the active layer and lithium fluoride (LiF) as the gate dielectric layer were investigated. Fabricateddevices exhibited ambipolar behavior that can be controlled by the applied source, drain and gate biases. It was found that at low source-drain biases, multistep hopping is the dominant conduction mechanism, whereas in high voltage regimes, I-V data fits in the Fowler-Nordheim(FN)tunneling model. The relationship between the applied gate bias and the field enhancement factor, which is the ratio of the local surface electric field to the applied electric field, were determined from the slope of the FN plots. The dependency between the transition points in conduction mechanism upon gate bias has also been extracted from the FN plots. The transition points show more dependency on gate voltage for negative biases compared to the positive biases.
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1202
Surface Acoustic Wave Sensors Deposited on AlN Thin Films
Over the past few decades, there has been considerable research and advancement in surface acoustic wave (SAW) technology. At present, SAW devices have been highly successful as frequency band pass filters for the mobile telecommunications and electronics industries. In addition to their inherent frequency selectivity, SAW devices are also highly sensitive to surface perturbations. This sensitivity, along with a relative ease of manufacture, makes SAW devices ideally suited for many sensing applications including mass, pressure, temperature, and biosensors. In the area of biosensing, surface plasmon resonance (SPR) and quartz crystal microbalances (QCM) are still in the forefront of research and development, but advancement in SAW sensors could prove to have significant advantages over these technologies. This study investigates the advantages of using aluminum nitride (AlN) as a material for SAW sensors. AlN retains its piezoelectric properties at relatively high temperatures when compared to more common piezoelectric materials such as lead zirconium titanate (PZT), lithium tantalate (LiTaO3) and zinc oxide (ZnO). AlN is also a very robust material making it suitable for biosensing applications where the sensing target is selectively absorbed by an active layer on the device which may attack the piezoelectric layer. AlN thin films of different thicknesses have been deposited on Si substrates by DC reactive sputtering. Rayleigh-wave SAW devices have been fabricated by the deposition of platinum contacts and interdigital transducers (IDTs) onto AlN thin films using standard photolithographic processes. Experiments have been conducted to measure Rayleigh velocities, resonant frequencies, and insertion loss. Experimental results are compared to theoretical calculations.
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1202
Surface Acoustic Wave Sensors Deposited on AlN Thin Films
Over the past few decades, there has been considerable research and advancement in surface acoustic wave (SAW) technology. At present, SAW devices have been highly successful as frequency band pass filters for the mobile telecommunications and electronics industries. In addition to their inherent frequency selectivity, SAW devices are also highly sensitive to surface perturbations. This sensitivity, along with a relative ease of manufacture, makes SAW devices ideally suited for many sensing applications including mass, pressure, temperature, and biosensors. In the area of biosensing, surface plasmon resonance (SPR) and quartz crystal microbalances (QCM) are still in the forefront of research and development, but advancement in SAW sensors could prove to have significant advantages over these technologies. This study investigates the advantages of using aluminum nitride (AlN) as a material for SAW sensors. AlN retains its piezoelectric properties at relatively high temperatures when compared to more common piezoelectric materials such as lead zirconium titanate (PZT), lithium tantalate (LiTaO3) and zinc oxide (ZnO). AlN is also a very robust material making it suitable for biosensing applications where the sensing target is selectively absorbed by an active layer on the device which may attack the piezoelectric layer. AlN thin films of different thicknesses have been deposited on Si substrates by DC reactive sputtering. Rayleigh-wave SAW devices have been fabricated by the deposition of platinum contacts and interdigital transducers (IDTs) onto AlN thin films using standard photolithographic processes. Experiments have been conducted to measure Rayleigh velocities, resonant frequencies, and insertion loss. Experimental results are compared to theoretical calculations.
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1202
Properties of Digital Aluminum Gallium Nitride Alloys Grown via Metal Organic Vapor Phase Epitaxy
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1202
Properties of Digital Aluminum Gallium Nitride Alloys Grown via Metal Organic Vapor Phase Epitaxy
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1195
Dependency of Indium Concentration on Structural Defects in MOVPE-grown InGaN/GaN Heterostructures
Indium Gallium Nitride (InxGa1-xN) alloys are currently playing an ever increasing role in optoelectronic devices as the bandgap of such alloys can theoretically be tuned between 0.7eV and 3.4eV–covering the entire visible spectrum. Although growth of high quality InxGa1-xN alloys with high indium mole fractions are difficult or presently unattainable, InGaN alloys are still a viable choice for light emitters and detectors over the visible (blue/green) to ultraviolet spectrum. However, many inherent problems during InGaN growth via Metal Organic Vapor Phase Epitaxy (MOVPE) arise due to the large lattice mismatch and low miscibility between GaN and InN–leading to the formation of Inverted Hexagonal Pyramid (IHP) defects at the termination of threading dislocations. Additionally, growth of InGaN at lower temperatures to promote increased indium incorporation results in poor surface morphology. Several methods such as strained layer superlattices and low mole fraction InGaN layers before the growth of the InGaN/GaN MQW structures have been shown to relive strain in the MQWs, thus reducing the density of IHP defects and/or improving the optical output characteristics. This work focuses on the application of GaN monolayer insertions during InGaN quantum well growth via Metal Organic Vapor Phase Epitaxy (MOVPE) as a means to reduce the IHP defect density and passivate effects on surface roughness while observing variations in indium concentration. Observations include the reduction of IHP defect density by nearly twofold as the number of GaN monolayer interruptions increase from zero to three while sustaining only slightly lower effective indium concentrations.
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1195
Dependency of Indium Concentration on Structural Defects in MOVPE-grown InGaN/GaN Heterostructures
Indium Gallium Nitride (InxGa1-xN) alloys are currently playing an ever increasing role in optoelectronic devices as the bandgap of such alloys can theoretically be tuned between 0.7eV and 3.4eV–covering the entire visible spectrum. Although growth of high quality InxGa1-xN alloys with high indium mole fractions are difficult or presently unattainable, InGaN alloys are still a viable choice for light emitters and detectors over the visible (blue/green) to ultraviolet spectrum. However, many inherent problems during InGaN growth via Metal Organic Vapor Phase Epitaxy (MOVPE) arise due to the large lattice mismatch and low miscibility between GaN and InN–leading to the formation of Inverted Hexagonal Pyramid (IHP) defects at the termination of threading dislocations. Additionally, growth of InGaN at lower temperatures to promote increased indium incorporation results in poor surface morphology. Several methods such as strained layer superlattices and low mole fraction InGaN layers before the growth of the InGaN/GaN MQW structures have been shown to relive strain in the MQWs, thus reducing the density of IHP defects and/or improving the optical output characteristics. This work focuses on the application of GaN monolayer insertions during InGaN quantum well growth via Metal Organic Vapor Phase Epitaxy (MOVPE) as a means to reduce the IHP defect density and passivate effects on surface roughness while observing variations in indium concentration. Observations include the reduction of IHP defect density by nearly twofold as the number of GaN monolayer interruptions increase from zero to three while sustaining only slightly lower effective indium concentrations.
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1207
Fabrication of Two Dimensional Array of Silica Nanospheres on GaN Using Spin Coating Method and Nomarski Image Processing
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1207
Fabrication of Two Dimensional Array of Silica Nanospheres on GaN Using Spin Coating Method and Nomarski Image Processing