Jonathan D'Angelo

Thermoelectric materials can be used for cooling/heating applications, or converting waste heat into electricity. Novel thermoelectric materials have been discovered in recent years. Characterization of an electrical conductivity and thermopower of a sample from room temperature to ≥900 K is often necessary for thermoelectric materials. This paper describes a system built for measurement of the power factor of thermoelectric materials from 300 to 1273 K. Characterization results of the system are also presented.

Thermoelectric generators can be used for converting waste heat into electric power. Significant interest in developing new materials in recent years has led to the discovery of several promising thermoelectrics, however, there can be considerable challenges in developing the materials into working devices. Testing and feedback is needed at each step to gain valuable information for identification of difficulties, quality of the materials and modules, repeatability in fabrication, and longevity of the devices. This paper describes a long-term module testing system for monitoring the output power of a module over extended testing times. To evaluate the system, we have tested commercially available thermoelectric modules over a one month time period.

The U.S. military uses large amounts of fuel during deployments and battlefield operations. Consequently, the U.S. military has a strong need to develop technologies that increase fuel efficiency and minimize fuel requirements all along the logistics trail and in all battlefield operations. There are additional requirements to reduce and minimize the environmental footprint of various military equipment and operations and reduce the need for batteries (non-rechargeable) in battlefield operations. The tri-agency SERDP (Strategic Environmental Research and Development Program) office is sponsoring a challenging, high-payoff project to develop a lightweight, small form-factor, soldier-portable advanced thermoelectric generator (TEG) system prototype to recover and convert waste heat from a variety of deployed equipment with the ultimate purpose of obtaining additional power for soldier battery charging, advanced capacitor charging, and other battlefield power applications. The project seeks to achieve power conversion efficiencies of 10% (double current commercial TE conversion efficiencies) in a system with ˜1.6-kW power output for a spectrum of battlefield power applications. In order to meet this objective, the project is taking on the multi-faceted challenges of tailoring LAST/LASTT-based thermoelectric (TE) materials for the proper temperature ranges (300 K – 700 K), fabricating these materials with cost-effective hot-pressed and sintered processes while maintaining their TE properties, measuring and characterizing their thermal fatigue and structural properties, developing the proper manufacturing processes for the TE materials and modules, designing and fabricating the necessary microtechnology heat exchangers, and fabricating and testing the final TEG system. The ultimate goal is to provide an opportunity to deploy these TEG systems in a wide variety of current military equipment. This would help the Army in achieving one of the Office of Secretary of Defense’s major strategic objectives to maintain and enhance operational effectiveness while reducing total force energy demands. The presentation will review the progress made on 1) the performance of LAST / LASTT TE materials and tailoring their temperature dependency; 2) evaluating the structural (Elastic modulus, Poisson’s ratio and mechanical strength) properties of these materials, 3) development of the necessary LAST/LASTT-based TE modules, 4) development of the required hot- and cold-side microtechnology heat exchangers, and 5) the overall system designs for 30 kW and 60 kW TQG applications and potential performance pathways/differences for these two TQG cases. This work leverages critical fundamental research performed by the Office of Naval Research in developing LAST/LASTT materials.

Lead-Antimony-Silver-Tellurium (L-A-S-T) materials, synthesized at Michigan State University, show promising thermoelectric properties at high temperatures for use in power generation applications. Recent scaled-up quantities of L-A-S-T show a ZT=1.4 at 700 K approaching the figure of merit for samples made in small quantities. These materials are of great interest for power generation applications with hot side temperatures in the range of 600-800 K. Developing these materials into working devices requires minimization of the thermal and electrical parasitic contact resistances, so various fabrication methods are under investigation. To examine each method, a new measurement system has been developed to characterize these devices under various load and temperature gradients. An introduction to the system will be presented, as well as results for devices made of the L-A-S-T materials.