MTMasao Takeyama

Masao Takeyama

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Masao Takeyama has a total of 46 co-authors. Here are the top co-authors by number of shared publications:

  • Satoru Kobayashi

    Department of Materials Science & Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology

    5 shared publications
  • Hirotoyo Nakashima

    Department of Materials Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 2-12-1 Ookayama Meguro-ku, Tokyo 152-8552, Japan

    3 shared publications
  • Hideki Wakabayashi

    Dept. Materials Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, Meguro-ku, Tokyo, Japan

    2 shared publications
  • Hirotoyo Nakashima

    Department of Materials Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology

    2 shared publications
  • Ryosuke Yamagata

    Department of Materials Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology

    2 shared publications
  • Ryosuke Yamagata

    Department of Materials Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, Tokyo, Japan

    2 shared publications

Latest Publications

  • Open Access

    Grain Boundary Precipitation Control of GCP Phase Using TCP or A2 Phase in Ni-Based Alloys

    by Shuntaro Ida, Ryosuke Yamagata, Hirotoyo Nakashima, Satoru Kobayashi, Masao Takeyama

    To cover the grain boundary (GB) of the Ni phase with precipitates, the GB precipitation behavior of both topologically close-packed (TCP) or A2 and geometrically close-packed (GCP) phases was investigated in two Ni–Nb–(Co, Cr) ternary systems. The Ni/TCP or A2/GCP three-phase region existed in both systems. In the Ni-Nb-Co ternary system, Nb was approximately equally partitioned into both Co7Nb2 (mC18 structure, TCP) and (Ni, Co)3Nb (D019 structure, GCP) phases. In the Ni–Nb-Cr ternary system, Nb and Cr were mainly partitioned into the Ni3Nb (D0a structure, GCP) and Cr (A2 structure) phases, respectively. In the Ni–Nb–Co ternary system, the Co7Nb2 phase grew along the GB, whereas the (Ni, Co)3Nb phase grew toward the grain interior (GI). However, the growth of the Ni3Nb phase toward the GI was suppressed in the Ni–Nb–Cr ternary system. The suppression of growth of the GCP phase and covering the GB using both the TCP or A2 and GCP phases might be possible in a system where the precipitation of the GCP phase nucleating on the GB prior to the TCP or A2 phase increases supersaturation for precipitation of the TCP or A2 phase.


  • Effects of Zr Addition on Precipitation and Stability of Fe2Nb Laves and Ni3Nb Phases in Novel Fe–Cr–Ni–Nb Austenitic Heat-resistant Steels

    by Seongtak Oh, Hirotoyo Nakashima, Ryosuke Yamagata, Satoru Kobayashi, Masao Takeyama

    Effects of Zr addition on the microstructure formation of two intermetallic phases of Fe2Nb Laves (TCP) and Ni3Nb (GCP) in a carbon-free Fe-20Cr-35Ni-2.5Nb (at.%) novel austenitic heat-resistant steel at elevated temperatures were examined from the viewpoints of thermodynamics and kinetics. From a thermodynamic perspective, the maximum solubility of Zr in the matrix phase is about 0.1 at.% under homogenization treated states at around 1473 K. The dissolved Zr in the matrix eventually reduces the solubility limit of Nb, thereby playing an important role in promoting the formation of grain-boundary Fe2Nb phase as well as that of thermodynamically stable Ni3Nb-δ phase within grain interiors after long-term aging at 1073 K. The Zr dissolved in the matrix after the homogenization treatment is found to enrich in δ phase formed during the aging and raises the temperature limit of formation of δ phase by about 50 K. From a kinetic perspective, because of the increase in Nb supersaturation, the dissolved Zr not only enhances the precipitation of Laves phase at grain boundaries but also promotes the homogeneous nucleation of metastable Ni3Nb-γ″ phase within grain interiors from the beginning of aging and retards the phase transformation from γ″ to δ. These microstructure changes by Zr can be interpreted in terms of the phase equilibria and relative phase stability among different phases. The present results reveal that even a small amount of Zr in solution, not segregation to grain boundaries, has tremendous effects on the precipitation behavior and morphology of intermetallic phases.


  • Open Access

    Improving the Tensile Properties of Additively Manufactured β-Containing TiAl Alloys via Microstructure Control Focusing on Cellular Precipitation Reaction

    by Ken Cho, Hirotaka Odo, Keisuke Okamoto, Hiroyuki Y. Yasuda, Hirotoyo Nakashima, Masao Takeyama, Takayoshi Nakano

    The effect of a two-step heat treatment on the microstructure and high-temperature tensile properties of β-containing Ti-44Al-4Cr (at%) alloys fabricated by electron beam powder bed fusion were examined by focusing on the morphology of α2/γ lamellar grains and β/γ cells precipitated at the lamellar grain boundaries by a cellular precipitation reaction. The alloys subjected to the first heat treatment step at 1573 K in the α + β two-phase region exhibit a non-equilibrium microstructure consisting of the α2/γ lamellar grains with a fine lamellar spacing and a β/γ duplex structure located at the grain boundaries. In the second step of heat treatment, i.e., aging at 1273 K in the β + γ two-phase region, the β/γ cells are discontinuously precipitated from the lamellar grain boundaries due to excess Cr supersaturation in the lamellae. The volume fraction of the cells and lamellar spacing increase with increasing aging time and affect the tensile properties of the alloys. The aged alloys exhibit higher strength and comparable elongation at 1023 K when compared to the as-built alloys. The strength of these alloys is strongly dependent on the volume fraction and lamellar spacing of the α2/γ lamellae. In addition, the morphology of the β/γ cells is also an important factor controlling the fracture mode and ductility of these alloys.


  • Design Approaches and Achievements of Novel Wrought TiAl Alloys for Jet Engine Applications

    by Hideki Wakabayashi, Loris J. Signori, Ali Shaaban, Ryosuke Yamagata, Hirotoyo Nakashima, Masao Takeyama


  • Effect of Homogenization on Creep of Additive Manufactured Alloy 718

    by Tomoki Otsuka, Hideki Wakabayashi, Daisuke Igarashi, Achmad Ariaseta, Shinya Imano, Yuting Wang, Satoru Kobayashi, Masao Takeyama


  • Microscale Fracture Toughness Testing of TiAl PST Crystals

    by Daisuke Miyaguchi, Masaaki Otsu, Kazuki Takashima, Masao Takeyama


  • Change in Creep Deformation of PST Crystals with Different Stress Axes

    by Xiaohua Min, Eisaku Sakurada, Masao Takeyama, Takashi Matsuo

    Based on our analysis of a lot of creep rate-strain curves of PST crystals with the different angles between the lamellar plate and the stress axis, designated as ø, it was confirmed that the creep rate and the creep deformation manner strongly depend on the ø. It was supposed that the predominant creep deformation using γ plate during the transient stage is derived by the fully suppression of the operation of another slip systems not parallel to γ plate through α2 plate. It was also confirmed that the initial stress axes of the PST crystals within the standard stereographic triangle move for the [001]-[111] line, and then turn their directions for [111] pole during the transient stage. This moving manner of the stress axis indicated that the first slip system of [101](111) continues to the area near the [001]-[111] line in the standard stereographic triangle, and then, the second slip system of [110](111) operates. By comparing this moving manner to the creep rate-strain curve, it is suggested that the first slip system of [101](111) operates during the Stage I where the light decrease in the creep rate remains, after that, the second slip system of [110](111) appears and leads to steep decrease in the creep rate. This stage was designated as the Stage II. According to this conception, it is supposed that the strain at the end of the Stage I is directly correlated with the angle from the initial stress axis to the [001]-[111] line in the standard stereographic triangle. In this study, this supposition was confirmed by conducting the creep tests at 1148 K/68.6 MPa using two PST crystals with ø of 31° and 34°. The initial stress axis of the PST crystal with ø of 31° locates nearer to the [001]-[-111] line than that of the PST crystal with ø of 34°. The strain at the end of the Stage I of the PST crystal with ø of 31° is half that of the PST crystal with ø of 34°. By analyzing the inverse pole figures of the creep interrupted PST crystals, it was confirmed that the angle from the initial stress axis to the [001]-[111] line is correlated with the strain of the transient stage.

  • On The Influence of Nb on the Transition Temperatures of Titanium Aluminides

    by Harald F. Chladil, Helmut Clemens, Masao Takeyama, Ernst Kozeschnik, Arno Bartels, Rainer Gerling, Sascha Kremmer

    Phase transformations and phase transition temperatures in several Ti-45Al and Ti-45Al-(5-10)Nb (at%) alloys were investigated experimentally and compared to thermodynamic calculation. The present study combines scanning electron microscopy, high-energy and conventional X-ray diffraction as well as differential scanning calorimetry for the characterization of the prevailing phases and phase transformations. Thermodynamic simulation based on the CALPHAD method was used to predict phase stabilities. Modifications of a commercial available database, based on the thermo-physical measurements and long-term annealing treatments, were introduced in order to achieve better agreement between calculated and experimental results.