Junfen Wan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Junfen Wan has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Xuejun Cao
State Key Laboratory of Bioreactor Engineering, Department of Bioengineering, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237, China
17 shared publications Xue Yu
State Key Laboratory of Bioreactor Engineering, Department of Bioengineering, East China University of Science and Technology, 130 Meilong Rd, Shanghai 200237, PR China; Shandong Key Laboratory of Biophysics, Institute of Biophysics, Dezhou University, Dezhou 253023, PR China
5 shared publicationsXi Chen
State Key Laboratory of Bioreactor Engineering, Department of Bioengineering, East China University of Science and Technology, 130 Meilong Road, Shanghai, 200237 China
4 shared publicationsHainan Zeng
State Key Laboratory of Bioreactor Engineering Department of Bioengineering East China University of Science and Technology Shanghai P. R. China
3 shared publicationsJianhui Xin
Shandong Key Laboratory of Biophysics, Institute of Biophysics, Dezhou University, Dezhou 253023, PR China
2 shared publicationsMengxia Yan
Shandong Key Laboratory of Biophysics, Institute of Biophysics, Dezhou University, Dezhou 253023, PR China
2 shared publications
Latest Publications
- Open Access
- 19 April 2025
- Published by MDPI AG in Pharmaceutics
- Vol. 17 (4) , 534
A Convenient Strategy for Studying Antibody Aggregation and Inhibition of Aggregation: Characterization and Simulation
Background/Objectives: Protein aggregation, particularly the aggregation of antibody-based drugs, has long been a significant challenge in downstream processes and formulation. While the inhibitory effects of excipients on aggregation have been extensively studied using early experimental characterization methods, complete formulation research requires significant amounts of antibodies and time, resulting in high research costs. Methods: This study proposed a quick and small-scale position-restrained simulation method which elucidated the mechanism of the reversible self-association (RSA) of antibodies and the influence of excipients on RSA under different conditions. We also validated the rationality of rapid and small-scale simulations through long-term (>1 μs) and large-scale (>1,000,000 atoms) simulations. Results: Through combing with simple stability characterization, the effects of different excipients on monomer residual content and the trend shown with concentration changes after thermal incubation were found to be similar to those observed in the simulations. Additionally, the formulation proposed by the simulations was validated using experimental characterization. Conclusions: Simulations and experiments revealed the mechanism and showed consistent trends, providing better understanding for aggregation research.
- 19 April 2025
- Published by MDPI AG in Pharmaceutics
- Vol. 17 (4) , 534
Open AccessA Convenient Strategy for Studying Antibody Aggregation and Inhibition of Aggregation: Characterization and Simulation
Background/Objectives: Protein aggregation, particularly the aggregation of antibody-based drugs, has long been a significant challenge in downstream processes and formulation. While the inhibitory effects of excipients on aggregation have been extensively studied using early experimental characterization methods, complete formulation research requires significant amounts of antibodies and time, resulting in high research costs. Methods: This study proposed a quick and small-scale position-restrained simulation method which elucidated the mechanism of the reversible self-association (RSA) of antibodies and the influence of excipients on RSA under different conditions. We also validated the rationality of rapid and small-scale simulations through long-term (>1 μs) and large-scale (>1,000,000 atoms) simulations. Results: Through combing with simple stability characterization, the effects of different excipients on monomer residual content and the trend shown with concentration changes after thermal incubation were found to be similar to those observed in the simulations. Additionally, the formulation proposed by the simulations was validated using experimental characterization. Conclusions: Simulations and experiments revealed the mechanism and showed consistent trends, providing better understanding for aggregation research.
- 17 August 2024
- Published by Elsevier in Journal of Chromatography A
- Vol. 1735, 465282
Highly selective separation and purification of lincomycin by macroporous adsorption resin column chromatography
- 17 August 2024
- Published by Elsevier in Journal of Chromatography A
- Vol. 1735, 465282
Highly selective separation and purification of lincomycin by macroporous adsorption resin column chromatography
- Open Access
Rational Design of Non-Covalent Imprinted Polymers Based on the Combination of Molecular Dynamics Simulation and Quantum Mechanics Calculations
Molecular imprinting is a promising approach for developing polymeric materials as artificial receptors. However, only a few types of molecularly imprinted polymers (MIPs) are commercially available, and most research on MIPS is still in the experimental phase. The significant limitation has been a challenge for screening imprinting systems, particularly for weak functional target molecules. Herein, a combined method of quantum mechanics (QM) computations and molecular dynamics (MD) simulations was employed to screen an appropriate 2,4-dichlorophenoxyacetic acid (2,4-D) imprinting system. QM calculations were performed using the Gaussian 09 software. MD simulations were conducted using the Gromacs2018.8 software suite. The QM computation results were consistent with those of the MD simulations. In the MD simulations, a realistic model of the ‘actual’ pre-polymerisation mixture was obtained by introducing numerous components in the simulations to thoroughly investigate all non-covalent interactions during imprinting. This study systematically examined MIP systems using computer simulations and established a theoretical prediction model for the affinity and selectivity of MIPs. The combined method of QM computations and MD simulations provides a robust foundation for the rational design of MIPs.
Open AccessRational Design of Non-Covalent Imprinted Polymers Based on the Combination of Molecular Dynamics Simulation and Quantum Mechanics Calculations
Molecular imprinting is a promising approach for developing polymeric materials as artificial receptors. However, only a few types of molecularly imprinted polymers (MIPs) are commercially available, and most research on MIPS is still in the experimental phase. The significant limitation has been a challenge for screening imprinting systems, particularly for weak functional target molecules. Herein, a combined method of quantum mechanics (QM) computations and molecular dynamics (MD) simulations was employed to screen an appropriate 2,4-dichlorophenoxyacetic acid (2,4-D) imprinting system. QM calculations were performed using the Gaussian 09 software. MD simulations were conducted using the Gromacs2018.8 software suite. The QM computation results were consistent with those of the MD simulations. In the MD simulations, a realistic model of the ‘actual’ pre-polymerisation mixture was obtained by introducing numerous components in the simulations to thoroughly investigate all non-covalent interactions during imprinting. This study systematically examined MIP systems using computer simulations and established a theoretical prediction model for the affinity and selectivity of MIPs. The combined method of QM computations and MD simulations provides a robust foundation for the rational design of MIPs.
- 12 April 2024
- Published by Elsevier in Journal of Chromatography A
- Vol. 1725, 464876
Computational design and preparation of water-compatible noncovalent imprinted microspheres
- 12 April 2024
- Published by Elsevier in Journal of Chromatography A
- Vol. 1725, 464876
Computational design and preparation of water-compatible noncovalent imprinted microspheres
- 11 March 2023
- Published by Elsevier in Journal of Chromatography A
- Vol. 1694, 463921
Prediction and validation of monoclonal antibodies separation in aqueous two-phase system using molecular dynamic simulation
- 11 March 2023
- Published by Elsevier in Journal of Chromatography A
- Vol. 1694, 463921
Prediction and validation of monoclonal antibodies separation in aqueous two-phase system using molecular dynamic simulation
- 18 January 2023
- Published by Taylor & Francis in Preparative Biochemistry & Biotechnology
- Vol. 53 (9) , 1092-1098
Optimization of extraction tower structure and extraction conditions for lincomycin separation
Lincomycin is a widely used aminoglycoside antibiotic. For its separation from fermentation broth in production, solvent extraction is usually applied because of its low cost and high capacity compared to other bioseparation methods. The multistage mixer-settler is a common extraction equipment in commercial production, but it occupies a large area and causes pollution. In this study, a fully enclosed turbine tower was designed and applied in order to replace the mixer-settler. Its structure parameters (turbine diameter, tray porosity) were optimized on the basis of the extraction effect of lincomycin. The results showed that with 35% tray porosity and 28/26 mm turbine diameter of the tower, the extraction rate was kept above 99.0% steadily under 375 rpm/min rotating speed and 60 °C temperature. The extraction effect is much better than mixer-settler and such turbine tower is expected to be applied in the commercial production of lincomycin.
- 18 January 2023
- Published by Taylor & Francis in Preparative Biochemistry & Biotechnology
- Vol. 53 (9) , 1092-1098
Optimization of extraction tower structure and extraction conditions for lincomycin separation
Lincomycin is a widely used aminoglycoside antibiotic. For its separation from fermentation broth in production, solvent extraction is usually applied because of its low cost and high capacity compared to other bioseparation methods. The multistage mixer-settler is a common extraction equipment in commercial production, but it occupies a large area and causes pollution. In this study, a fully enclosed turbine tower was designed and applied in order to replace the mixer-settler. Its structure parameters (turbine diameter, tray porosity) were optimized on the basis of the extraction effect of lincomycin. The results showed that with 35% tray porosity and 28/26 mm turbine diameter of the tower, the extraction rate was kept above 99.0% steadily under 375 rpm/min rotating speed and 60 °C temperature. The extraction effect is much better than mixer-settler and such turbine tower is expected to be applied in the commercial production of lincomycin.
- Open Access
- 30 December 2021
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (1) , 683-687
Conversion of Calcium Citrate to Citric Acid with Compressed CO2
Citric acid is mainly produced in the fermentation industry, which needs complex processes and produces a high amount of CaSO4 as waste. In this study, CO2 has been used to convert calcium citrate to citric acid and CaCO3 by controlling the reaction parameters (reactants ratio, temperature, and pressure). The CaCO3 produced in this conversion could further be used in the fermentation industry for citric acid production. The transformation condition has been optimized by controlling temperature, pressure, reaction time, and mass ratio of calcium citrate and water. The highest conversion could reach up to 94.7% under optimal experimental conditions of 18 MPa of pressure, 65 °C of reaction temperature, 4 h of reaction time, and 2 g/L of calcium citrate/water suspension solution. This method features simple process, easy separation of citric acid, and environmentally friendly process, which could be a potentially alternative route for downstream treatment in fermentation production of citric acid.
- 30 December 2021
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (1) , 683-687
Open AccessConversion of Calcium Citrate to Citric Acid with Compressed CO2
Citric acid is mainly produced in the fermentation industry, which needs complex processes and produces a high amount of CaSO4 as waste. In this study, CO2 has been used to convert calcium citrate to citric acid and CaCO3 by controlling the reaction parameters (reactants ratio, temperature, and pressure). The CaCO3 produced in this conversion could further be used in the fermentation industry for citric acid production. The transformation condition has been optimized by controlling temperature, pressure, reaction time, and mass ratio of calcium citrate and water. The highest conversion could reach up to 94.7% under optimal experimental conditions of 18 MPa of pressure, 65 °C of reaction temperature, 4 h of reaction time, and 2 g/L of calcium citrate/water suspension solution. This method features simple process, easy separation of citric acid, and environmentally friendly process, which could be a potentially alternative route for downstream treatment in fermentation production of citric acid.
- 24 November 2021
- Published by Wiley in Journal of Separation Science
- Vol. 45 (2) , 570-581
Effective extraction of tylosin and spiramycin from fermentation broth using thermo‐responsive ethylene oxide/propylene oxide aqueous two‐phase systems
Recyclable aqueous two‐phase systems with thermo‐responsive phase‐forming materials have been employed to separate macromolecules; however, these systems have achieved very limited separation efficiency for small molecules, such as antibiotics. In this study, aqueous two‐phase systems composed of the ethylene oxide/propylene oxide copolymer and water were developed to extract alkaline antibiotics from the fermentation broth. In the aqueous two‐phase systems with an ethylene oxide ratio of 20 and propylene oxide ratio of 80, the partition coefficients of tylosin and spiramycin reached 16.87 and 20.39, respectively, while the extraction recoveries were 70.67 and 86.70%, respectively. Coupled with mechanism analysis, we demonstrated the feasibility of extracting alkaline antibiotics using this aqueous two‐phase system, especially for 16‐membered macrolide antibiotics. The molecular dynamic simulation was employed to visualize the process of dual‐phase formation and the partition behavior of antibiotics in an aqueous two‐phase system. The dynamic simulation revealed the binding energy between the antibiotic and ethylene oxide/propylene oxide copolymers, which provides a simple indicator for screening suitable antibiotics in aqueous two‐phase systems. Our recyclable aqueous two‐phase systems provide a robust approach for the extraction of 16‐membered macrolide antibiotics with ease of operation and high recovery rates, which is appropriate for large‐scale extraction in the fermentation industry.
- 24 November 2021
- Published by Wiley in Journal of Separation Science
- Vol. 45 (2) , 570-581
Effective extraction of tylosin and spiramycin from fermentation broth using thermo‐responsive ethylene oxide/propylene oxide aqueous two‐phase systems
Recyclable aqueous two‐phase systems with thermo‐responsive phase‐forming materials have been employed to separate macromolecules; however, these systems have achieved very limited separation efficiency for small molecules, such as antibiotics. In this study, aqueous two‐phase systems composed of the ethylene oxide/propylene oxide copolymer and water were developed to extract alkaline antibiotics from the fermentation broth. In the aqueous two‐phase systems with an ethylene oxide ratio of 20 and propylene oxide ratio of 80, the partition coefficients of tylosin and spiramycin reached 16.87 and 20.39, respectively, while the extraction recoveries were 70.67 and 86.70%, respectively. Coupled with mechanism analysis, we demonstrated the feasibility of extracting alkaline antibiotics using this aqueous two‐phase system, especially for 16‐membered macrolide antibiotics. The molecular dynamic simulation was employed to visualize the process of dual‐phase formation and the partition behavior of antibiotics in an aqueous two‐phase system. The dynamic simulation revealed the binding energy between the antibiotic and ethylene oxide/propylene oxide copolymers, which provides a simple indicator for screening suitable antibiotics in aqueous two‐phase systems. Our recyclable aqueous two‐phase systems provide a robust approach for the extraction of 16‐membered macrolide antibiotics with ease of operation and high recovery rates, which is appropriate for large‐scale extraction in the fermentation industry.
- 17 May 2021
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 193 (10) , 3062-3078
Partition of Tea Saponin with a Novel Recyclable Thermo-pH Aqueous Two-Phase Systems
Aqueous two-phase systems (ATPS) have the advantages of environmentally friendly, high mass transfer efficiency, and mild extraction conditions. However, it is difficult to recycle these polymers, which limits the large-scale application of ATPS. In this study, a novel recyclable ATPS was constructed with thermo-responsive polymer PN and pH-responsive polymer PADB4.78 for the partition of tea saponin. PN represents poly-(N-isopropylacrylamide), and PADB4.78 represents poly-(acrylic acid-dimethylamine ethyl methacrylate-butyl methacrylate), where 4.78 in the subscript indicate the isoelectric point of the polymer. The recoveries of PN and PADB4.78 were 95.36% and 93.48%, respectively, after two cycles. Meanwhile, the phase formation mechanism of ATPS was studied by surface tension and low-field nuclear magnetic resonance (LF-NMR). The effects of polymer concentration, pH, temperature, types and concentrations of salt were investigated on tea saponin partition. In the 1.5% (w/v) PN/3.5% (w/v) PADB4.78 ATPS, the optimal partition coefficient (K) of crude tea saponin were 0.15 in the presence of 1.5 mM KCl at pH 7.6 and 25 °C while the extraction recovery (ERb) reached 92.13%. The K and ERb of tea saponin from tea seeds were 0.12 and 94.50% with 7.5 mM LiBr at pH 8.0 and 25 °C, respectively.
- 17 May 2021
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 193 (10) , 3062-3078
Partition of Tea Saponin with a Novel Recyclable Thermo-pH Aqueous Two-Phase Systems
Aqueous two-phase systems (ATPS) have the advantages of environmentally friendly, high mass transfer efficiency, and mild extraction conditions. However, it is difficult to recycle these polymers, which limits the large-scale application of ATPS. In this study, a novel recyclable ATPS was constructed with thermo-responsive polymer PN and pH-responsive polymer PADB4.78 for the partition of tea saponin. PN represents poly-(N-isopropylacrylamide), and PADB4.78 represents poly-(acrylic acid-dimethylamine ethyl methacrylate-butyl methacrylate), where 4.78 in the subscript indicate the isoelectric point of the polymer. The recoveries of PN and PADB4.78 were 95.36% and 93.48%, respectively, after two cycles. Meanwhile, the phase formation mechanism of ATPS was studied by surface tension and low-field nuclear magnetic resonance (LF-NMR). The effects of polymer concentration, pH, temperature, types and concentrations of salt were investigated on tea saponin partition. In the 1.5% (w/v) PN/3.5% (w/v) PADB4.78 ATPS, the optimal partition coefficient (K) of crude tea saponin were 0.15 in the presence of 1.5 mM KCl at pH 7.6 and 25 °C while the extraction recovery (ERb) reached 92.13%. The K and ERb of tea saponin from tea seeds were 0.12 and 94.50% with 7.5 mM LiBr at pH 8.0 and 25 °C, respectively.