Philip J. Brown
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Philip J. Brown has a total of 81 co-authors. Here are the top co-authors by number of shared publications:
- Kathryn Stevens
Center for Optical Materials Science & Engineering Technologies (COMSET), School of Materials Science and Engineering, Clemson University, Clemson, SC 29634, USA
2 shared publications A. Dinkelmann
1 shared publicationA. Scherrieble
1 shared publication- Alan Edward Tonelli
North Carolina State University
1 shared publication Alexander Sponner
1 shared publication- Andrew P. Monkman
Department of Physics Durham University Durham UK
1 shared publication
Latest Publications
- Open Access
Towards a Long-Chain Perfluoroalkyl Replacement: Water and Oil Repellent Perfluoropolyether-Based Polyurethane Oligomers
Original perfluoropolyether (PFPE)-based oligomeric polyurethanes (FOPUs) with different macromolecular architecture were synthesized (in one step) as low-surface-energy materials. It is demonstrated that the oligomers, especially the ones terminated with CF3 moieties, can be employed as safer replacements to long-chain perfluoroalkyl substances/additives. The FOPU macromolecules, when added to an engineering thermoplastic (polyethylene terephthalate, PET) film, readily migrate to the film surface and bring significant water and oil repellency to the thermoplastic boundary. The best performing FOPU/PET films have reached the level of oil wettability and surface energy significantly lower than that of polytetrafluoroethylene, a fully perfluorinated polymer. Specifically, the highest level of the repellency is observed with an oligomeric additive, which was made using aromatic diisocyanate as a comonomer and has CF3 end-group. This semicrystalline oligomer has a glass transition temperature (Tg) well above room temperature, and we associate the superiority of the material in achieving low water and oil wettability with its ability to effectively retain CF3 and CF2 moieties in contact with the test wetting liquids.
Open AccessTowards a Long-Chain Perfluoroalkyl Replacement: Water and Oil Repellent Perfluoropolyether-Based Polyurethane Oligomers
Original perfluoropolyether (PFPE)-based oligomeric polyurethanes (FOPUs) with different macromolecular architecture were synthesized (in one step) as low-surface-energy materials. It is demonstrated that the oligomers, especially the ones terminated with CF3 moieties, can be employed as safer replacements to long-chain perfluoroalkyl substances/additives. The FOPU macromolecules, when added to an engineering thermoplastic (polyethylene terephthalate, PET) film, readily migrate to the film surface and bring significant water and oil repellency to the thermoplastic boundary. The best performing FOPU/PET films have reached the level of oil wettability and surface energy significantly lower than that of polytetrafluoroethylene, a fully perfluorinated polymer. Specifically, the highest level of the repellency is observed with an oligomeric additive, which was made using aromatic diisocyanate as a comonomer and has CF3 end-group. This semicrystalline oligomer has a glass transition temperature (Tg) well above room temperature, and we associate the superiority of the material in achieving low water and oil wettability with its ability to effectively retain CF3 and CF2 moieties in contact with the test wetting liquids.
- Open Access
The Influence of Synthesis Parameters on Particle Size and Photoluminescence Characteristics of Ligand Capped Tb3+:LaF3
Organic ligand surface-treated Tb3+:LaF3 was synthesized in water and methanol for subsequent incorporation into polymethyl methacrylate (PMMA) via solution-precipitation chemistry in order to produce optically active polymer nanocomposites. Nanoparticle agglomerate diameters ranged from 388 ± 188 nm when synthesized in water and 37 ± 2 nm when synthesized in methanol. Suspension stability is paramount for producing optically transparent materials. Methanol nanoparticle synthesized at a pH of 3 exhibited the smallest agglomerate size. Optical spectroscopy, dynamic light scattering, transmission electron microscopy, scanning transmission electron microscopy, and zeta potential analysis were used to characterize the particles synthesized.
Open AccessThe Influence of Synthesis Parameters on Particle Size and Photoluminescence Characteristics of Ligand Capped Tb3+:LaF3
Organic ligand surface-treated Tb3+:LaF3 was synthesized in water and methanol for subsequent incorporation into polymethyl methacrylate (PMMA) via solution-precipitation chemistry in order to produce optically active polymer nanocomposites. Nanoparticle agglomerate diameters ranged from 388 ± 188 nm when synthesized in water and 37 ± 2 nm when synthesized in methanol. Suspension stability is paramount for producing optically transparent materials. Methanol nanoparticle synthesized at a pH of 3 exhibited the smallest agglomerate size. Optical spectroscopy, dynamic light scattering, transmission electron microscopy, scanning transmission electron microscopy, and zeta potential analysis were used to characterize the particles synthesized.
- 1 January 2007
- Published by Elsevier
Contributor contact details
- 1 January 2005
- Published by Elsevier
Contributor contact details
- 18 June 2003
- Published by Wiley in Advanced Materials
- Vol. 15 (13) , 1081-1084
Fabrication and Characteristics of 2‐Acrylamido‐2‐methyl‐1‐propanesulfonic Acid‐Doped Polyaniline Hollow Fibers
Polyaniline:2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid has been wet‐spun to yield hollow fibers using dichloroacetic acid as the solvent. The fibers have excellent circular cross‐sections and good surface morphology, as can be seen from the Figure. The permeability of the fibers, as suitable for gas separation, has been assessed.
- 18 June 2003
- Published by Wiley in Advanced Materials
- Vol. 15 (13) , 1081-1084
Fabrication and Characteristics of 2‐Acrylamido‐2‐methyl‐1‐propanesulfonic Acid‐Doped Polyaniline Hollow Fibers
Polyaniline:2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid has been wet‐spun to yield hollow fibers using dichloroacetic acid as the solvent. The fibers have excellent circular cross‐sections and good surface morphology, as can be seen from the Figure. The permeability of the fibers, as suitable for gas separation, has been assessed.
- 1 June 2002
- Published by Walter de Gruyter GmbH in Autex Research Journal
- Vol. 2 (2) , 101-108
MORPHOLOGICAL STRUCTURE OF POLYETHERKETONE MEMBRANES FOR GAS SEPARATION PREPARED BY PHASE INVERSION
There has been increasing worldwide interest in the field of technical textile materials. Within this context the use of membranes for industrial separation processes has developed, and they can now compete effectively with conventional processes in terms of energy and capital costs. Membranes for gas separation have developed significantly in the last twenty years; however, there is still a need for high-temperature and chemically resistant membranes that exhibit good selectivity and gas permeability. In spite of the developments in gas separation membranes, only a few types of hollowfibre membranes are still commercially available. Our study examines the fundamental properties of polyetherketone (PEK, a thermally stable and chemically resistant polymer) membranes prepared using concentrated sulphuric acid (98% H2SO4) as a solvent and dilute sulphuric acid (30%-60% H2SO4) as a non-solvent. Other non-solvents included acetic acid, ethanol, methanol, glycerol, and water. The concentration of the polymer-casting solutions was between 15% and 20%. The membrane structure was examined using SEM, and the gas separation properties were measured using a labscale test rig. The results show that formation and control of membrane structure are complicated, and that many preparation parameters affect membrane morphology and performance. Polymer concentration is a particularly important parameter. At each individual polymer concentration, the precipitant plays a crucial role, and has a determining influence on membrane structure. Membranes cast using 30-40% glycerol and 50-60% H2SO4 or 70-90% acetic acid as precipitants possessed sponge-type structures, and as such have an acceptable permeation rate. However, membranes cast into water display finger-like structures even at a low coagulation temperature of 3°C, and also exhibit lower permeation rates. It has also been shown that precipitated structures of PEK membranes are highly dependent upon the heat of mixing of the solvent with non-solvent, and that a reduction in this heat of mixing leads to sponge-like structures that are preferential for gas separation membranes.
- 1 June 2002
- Published by Walter de Gruyter GmbH in Autex Research Journal
- Vol. 2 (2) , 101-108
MORPHOLOGICAL STRUCTURE OF POLYETHERKETONE MEMBRANES FOR GAS SEPARATION PREPARED BY PHASE INVERSION
There has been increasing worldwide interest in the field of technical textile materials. Within this context the use of membranes for industrial separation processes has developed, and they can now compete effectively with conventional processes in terms of energy and capital costs. Membranes for gas separation have developed significantly in the last twenty years; however, there is still a need for high-temperature and chemically resistant membranes that exhibit good selectivity and gas permeability. In spite of the developments in gas separation membranes, only a few types of hollowfibre membranes are still commercially available. Our study examines the fundamental properties of polyetherketone (PEK, a thermally stable and chemically resistant polymer) membranes prepared using concentrated sulphuric acid (98% H2SO4) as a solvent and dilute sulphuric acid (30%-60% H2SO4) as a non-solvent. Other non-solvents included acetic acid, ethanol, methanol, glycerol, and water. The concentration of the polymer-casting solutions was between 15% and 20%. The membrane structure was examined using SEM, and the gas separation properties were measured using a labscale test rig. The results show that formation and control of membrane structure are complicated, and that many preparation parameters affect membrane morphology and performance. Polymer concentration is a particularly important parameter. At each individual polymer concentration, the precipitant plays a crucial role, and has a determining influence on membrane structure. Membranes cast using 30-40% glycerol and 50-60% H2SO4 or 70-90% acetic acid as precipitants possessed sponge-type structures, and as such have an acceptable permeation rate. However, membranes cast into water display finger-like structures even at a low coagulation temperature of 3°C, and also exhibit lower permeation rates. It has also been shown that precipitated structures of PEK membranes are highly dependent upon the heat of mixing of the solvent with non-solvent, and that a reduction in this heat of mixing leads to sponge-like structures that are preferential for gas separation membranes.