Richard W. Fonda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Richard W. Fonda has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- David J. Rowenhorst
U.S. Naval Research Laboratory
4 shared publications C. R. Feng
Naval Research Laboratory, Washington, DC, USA
2 shared publications- Erik Mejdal Lauridsen
Technical University of Denmark (Risø DTU)
2 shared publications Keith E. Knipling
Naval Research Laboratory, Washington, DC, USA
2 shared publications- Keith E. Knipling
Naval Research Laboratory, Washington, DC 20375, USA
2 shared publications - Wolfgang Ludwig
European Synchrotron Radiation Facility, 71 avenue des Martyrs, CS40220, 38043 Grenoble Cedex 9, France
2 shared publications
Latest Publications
- Open Access
- 1 July 2022
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1249 (1) , 012007
Crystallographic Variability in Additive Manufacturing
The crystallographic textures produced during additive manufacturing can be understood, predicted, and manipulated by varying the grain nucleation and growth processes. The resultant textures are primarily dictated by the melt pool geometry, which defines the local thermal gradient and thus the preferred crystal growth directions, as well as the scan strategy, which controls the propagation of grain orientations into subsequent layers. This texture can be diluted through heterogeneous nucleation of new grain orientations, which can occur through a variety of mechanisms. This ability to control the texture during additive manufacturing can enable the location-specific control of properties as a function of position in the build.
- 1 July 2022
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1249 (1) , 012007
Open AccessCrystallographic Variability in Additive Manufacturing
The crystallographic textures produced during additive manufacturing can be understood, predicted, and manipulated by varying the grain nucleation and growth processes. The resultant textures are primarily dictated by the melt pool geometry, which defines the local thermal gradient and thus the preferred crystal growth directions, as well as the scan strategy, which controls the propagation of grain orientations into subsequent layers. This texture can be diluted through heterogeneous nucleation of new grain orientations, which can occur through a variety of mechanisms. This ability to control the texture during additive manufacturing can enable the location-specific control of properties as a function of position in the build.
- 12 October 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (12) , 6560-6573
The Effects of Post-processing in Additively Manufactured 316L Stainless Steels
- 12 October 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (12) , 6560-6573
The Effects of Post-processing in Additively Manufactured 316L Stainless Steels
- 1 October 2019
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 24 (7) , 617-623
Enhancing the weldability of CP titanium friction stir welds with elemental foils
Friction stir welding (FSW) has proven to be a viable technique for joining a wide variety of alloys. However, thick section welding of alpha and near-alpha Ti alloys has proven particularly challenging. Previous research at the Naval Research Laboratory using Ni markers in CP Ti friction stir welds indicated that elemental additions of Ni to the joint line can provide substantial benefits for improved weldability of these alloys. The current study surveys the effects of Ni and other elemental additions to CP Ti friction stir welds to determine their influence on the resultant weld microstructure, weld surface finish, and welding machine forces. These results reveal that Ni provides the most benefits for the concentrations examined, but other elements may also provide benefits at lower concentrations. The addition of these elements may improve the weldability and weld quality for FSW of CP Ti, enabling thick section welding of this and similar alloys.
- 1 October 2019
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 24 (7) , 617-623
Enhancing the weldability of CP titanium friction stir welds with elemental foils
Friction stir welding (FSW) has proven to be a viable technique for joining a wide variety of alloys. However, thick section welding of alpha and near-alpha Ti alloys has proven particularly challenging. Previous research at the Naval Research Laboratory using Ni markers in CP Ti friction stir welds indicated that elemental additions of Ni to the joint line can provide substantial benefits for improved weldability of these alloys. The current study surveys the effects of Ni and other elemental additions to CP Ti friction stir welds to determine their influence on the resultant weld microstructure, weld surface finish, and welding machine forces. These results reveal that Ni provides the most benefits for the concentrations examined, but other elements may also provide benefits at lower concentrations. The addition of these elements may improve the weldability and weld quality for FSW of CP Ti, enabling thick section welding of this and similar alloys.
- 3 December 2018
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 50 (2) , 655-663
3D Material Flow in Friction Stir Welds
- 3 December 2018
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 50 (2) , 655-663
3D Material Flow in Friction Stir Welds
- 3 November 2015
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 47 (1) , 360-367
Thermal Stir Welds in Titanium
- 3 November 2015
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 47 (1) , 360-367
Thermal Stir Welds in Titanium
- 2 October 2014
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 45 (13) , 5982-5989
Effects of Cooling Rate on Transformations in a Fe-9 Pct Ni Steel
- 2 October 2014
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 45 (13) , 5982-5989
Effects of Cooling Rate on Transformations in a Fe-9 Pct Ni Steel
- 12 November 2013
- Published by Springer Nature in JOM
- Vol. 66 (1) , 149-155
EBSD Analysis of Friction Stir Weld Textures
- 12 November 2013
- Published by Springer Nature in JOM
- Vol. 66 (1) , 149-155
EBSD Analysis of Friction Stir Weld Textures
- 27 July 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 22 (11) , 3376-3380
Soldering a 3D Wire Lattice Structure
- 27 July 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 22 (11) , 3376-3380
Soldering a 3D Wire Lattice Structure
- 17 October 2012
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 44 (1) , 337-344
Material Flow in Friction Stir Welds
- 17 October 2012
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 44 (1) , 337-344
Material Flow in Friction Stir Welds
- 31 March 2011
- Published by Elsevier in Acta Materialia
- Vol. 59 (5) , 2240
Corrigendum to: Texture Development in Near-α Ti Friction Stir Welds [Acta Materialia 58(19), pp. 6452–6463]
- 31 March 2011
- Published by Elsevier in Acta Materialia
- Vol. 59 (5) , 2240
Corrigendum to: Texture Development in Near-α Ti Friction Stir Welds [Acta Materialia 58(19), pp. 6452–6463]