Keisuke Tanaka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Keisuke Tanaka has a total of 77 co-authors. Here are the top co-authors by number of shared publications:
- Yoshiaki Akiniwa
Yokohama National University
61 shared publications - Hidehiko Kimura
Nagoya University
8 shared publications Hirohisa Kimachi
Meijo University
7 shared publicationsKenji Suzuki
Faculty of Education and Human Sciences, Niigata University
7 shared publicationsHideki Okado
3 shared publications- Kenichi Shimizu
Department of Mechanical Engineering, Meijo University, Nagoya, Japan
3 shared publications
Latest Publications
- Open Access
- 1 August 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 996, 951-957
Residual Stress Evaluation of Short-Fiber Reinforced Plastics by X-Ray Diffraction
The X-ray diffraction method is used to evaluate the residual stress in injection-molded plates of short-fiber reinforced plastics (SFRP) made of crystalline thermoplastics, polyphenylene sulphide (PPS), reinforced by carbon fibers with 30 mass%. The stress in the matrix in the skin layer was determined using Cr-Kα radiation with the sin2 ψ method. The X-ray evaluation of stress in carbon fibers was not possible because of high texture. A new method was proposed to evaluate the macrostress in SFRP from the measurement of the matrix stress. According to micromechanics analysis of SFRP, the matrix stresses in the fiber direction and perpendicular to the fiber direction, and shear stress can be expressed as linear functions of the applied (macro-) stresses in the fiber direction and perpendicular to the fiber direction, and shear stress. The proportional constants are named stress-partitioning coefficients. Using skin-layer strips cut parallel, perpendicular and 45° to the molding direction, the stress in the matrix was evaluated under the uniaxial applied stress and the stress-partitioning coefficients of the above equations were determined. Once the relations between the macrostress and matrix stress are established, the macrostress in SFRP can be evaluated from the measurements of the matrix stresses using X-rays.
- 1 August 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 996, 951-957
Open AccessResidual Stress Evaluation of Short-Fiber Reinforced Plastics by X-Ray Diffraction
The X-ray diffraction method is used to evaluate the residual stress in injection-molded plates of short-fiber reinforced plastics (SFRP) made of crystalline thermoplastics, polyphenylene sulphide (PPS), reinforced by carbon fibers with 30 mass%. The stress in the matrix in the skin layer was determined using Cr-Kα radiation with the sin2 ψ method. The X-ray evaluation of stress in carbon fibers was not possible because of high texture. A new method was proposed to evaluate the macrostress in SFRP from the measurement of the matrix stress. According to micromechanics analysis of SFRP, the matrix stresses in the fiber direction and perpendicular to the fiber direction, and shear stress can be expressed as linear functions of the applied (macro-) stresses in the fiber direction and perpendicular to the fiber direction, and shear stress. The proportional constants are named stress-partitioning coefficients. Using skin-layer strips cut parallel, perpendicular and 45° to the molding direction, the stress in the matrix was evaluated under the uniaxial applied stress and the stress-partitioning coefficients of the above equations were determined. Once the relations between the macrostress and matrix stress are established, the macrostress in SFRP can be evaluated from the measurements of the matrix stresses using X-rays.
- 7 May 2010
- Published by Japan Society of Spring Engineers in Transactions of Japan Society of Spring Engineers
- Vol. 2010 (55) , 19-24
Effect of Hardness and Shot Peening on Torsional Fatigue Strength of High Strength Spring Steel
- 7 May 2010
- Published by Japan Society of Spring Engineers in Transactions of Japan Society of Spring Engineers
- Vol. 2010 (55) , 19-24
Effect of Hardness and Shot Peening on Torsional Fatigue Strength of High Strength Spring Steel
- 4 January 2008
- Published by Springer Nature
- p. 1217-1218
Resistance-Curve Method for Predicting Fatigue Thresholds under Combined Loading
- 4 January 2008
- Published by Springer Nature
- p. 1217-1218
Resistance-Curve Method for Predicting Fatigue Thresholds under Combined Loading
- 1 January 2007
- Published by Japan Society of Mechanical Engineers in The proceedings of the JSME annual meeting
- Vol. 2007.1, 287-288
2229 Nanoscopic Analysis on Deformation and Fracture Behavior of Ultrafine-grained Cu Processed by ECAP
- 1 January 2007
- Published by Japan Society of Mechanical Engineers in The proceedings of the JSME annual meeting
- Vol. 2007.1, 287-288
2229 Nanoscopic Analysis on Deformation and Fracture Behavior of Ultrafine-grained Cu Processed by ECAP
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 72 (718) , 914-921
Fatigue Crack Propagation under Combined Cyclic Mechanical Loading and Electric Field in Piezoelectric Ceramics
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 72 (718) , 914-921
Fatigue Crack Propagation under Combined Cyclic Mechanical Loading and Electric Field in Piezoelectric Ceramics
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 72 (720) , 1137-1144
Resistance-Curve Method for Predicting Fatigue Thresholds in Holed Specimens under Combined Torsional-Axial Loading
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 72 (720) , 1137-1144
Resistance-Curve Method for Predicting Fatigue Thresholds in Holed Specimens under Combined Torsional-Axial Loading
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 72 (717) , 765-771
X-Ray Stress Measurement of Silicon Single Crystal Using Multiple Regression Analysis
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A
- Vol. 72 (717) , 765-771
X-Ray Stress Measurement of Silicon Single Crystal Using Multiple Regression Analysis
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in The proceedings of the JSME annual meeting
- Vol. 2006.1, 203-204
2737 Opening Behavior of Cyclic Fatigue Cracks in Porous Ceramics
- 1 January 2006
- Published by Japan Society of Mechanical Engineers in The proceedings of the JSME annual meeting
- Vol. 2006.1, 203-204
2737 Opening Behavior of Cyclic Fatigue Cracks in Porous Ceramics
- 1 January 2005
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Tokai Branch
- Vol. 2005.54, 115-116
417 Prediction of Mechanical Properties of Polycrystalline Thin Films with Fiber Texture by Finite Element Method
- 1 January 2005
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Tokai Branch
- Vol. 2005.54, 115-116
417 Prediction of Mechanical Properties of Polycrystalline Thin Films with Fiber Texture by Finite Element Method
- 1 January 2005
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Tokai Branch
- Vol. 2005.54, 117-118
418 Evalution of Thermal Residual Stresses for Polycrystalline Thin Films by Finite Element Method
- 1 January 2005
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Tokai Branch
- Vol. 2005.54, 117-118
418 Evalution of Thermal Residual Stresses for Polycrystalline Thin Films by Finite Element Method