Raman P. Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Raman P. Singh has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Bhavesh G. Kumar
Department of Mechanical Engineering, State University of New York, Stony Brook, NY 11794, USA
1 shared publication- Engin Ozcivici
İzmir Institute of Technology
1 shared publication P. Dyjak
Mechanics of Advanced Materials Laboratory, Department of Mechanical Engineering, Stony Brook University, Stony Brook, USA
1 shared publicationR. Sriraman
John F Welch Technology Center, GE India Technology Center Pvt. Ltd., Bangalore, India
1 shared publicationS. C. Zunjarrao
Mechanics of Advanced Materials Laboratory, Department of Mechanical Engineering, State University of New York at Stony Brook, Stony Brook, USA
1 shared publicationToshio Nakamura
Department of Mechanical Engineering, State University of New York, Stony Brook, NY 11794, USA
1 shared publication
Latest Publications
- 1 April 2006
- Published by Springer Nature in Journal of Materials Science
- Vol. 41 (8) , 2219-2228
Effect of processing parameters and clay volume fraction on the mechanical properties of epoxy-clay nanocomposites
- 1 April 2006
- Published by Springer Nature in Journal of Materials Science
- Vol. 41 (8) , 2219-2228
Effect of processing parameters and clay volume fraction on the mechanical properties of epoxy-clay nanocomposites
- 27 March 2006
- Published by Springer Nature in Experimental Mechanics
- Vol. 46 (3) , 333-345
Acoustic Emission Analysis of Nanoindentation-Induced Fracture Events
- 27 March 2006
- Published by Springer Nature in Experimental Mechanics
- Vol. 46 (3) , 333-345
Acoustic Emission Analysis of Nanoindentation-Induced Fracture Events
- 19 August 2005
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 88 (12) , 3338-3345
Fabrication and Characterization of Ceramic Foams Based on Silicon Carbide Matrix and Hollow Alumino‐Silicate Spheres
Closed‐cell foams were fabricated by incorporating two different grades of hollow alumino‐silicate spheres (cenospheres) into a silicon carbide matrix. The matrix was formed by the pyrolysis of a preceramic polymer, and multiple polymer infiltration and pyrolysis (PIP) cycles were employed to minimize the open voids in the material. The physical, mechanical and thermal properties of the fabricated foams were characterized as functions of the number of reinfiltration cycles. The open‐ and closed‐void volume fractions were determined by measurements of bulk and skeletal densities. Mechanical properties, including strength and modulus, were evaluated using four‐point bend and compression tests. Finally, thermal properties of the material, including the coefficient of thermal expansion and the thermal conductivity, were determined using dilatometry and the laser‐flash technique, respectively. This processing technique results in closed‐cell syntactic foams with minimal porosity (∼2–4%), reasonable mechanical strength (∼30 MPa) and very low thermal conductivity (≤1 W/m·K). In this manner, this process can be used for the low‐cost and net‐shape fabrication of closed‐cell silicon carbide‐based syntactic foams for high‐temperature applications.
- 19 August 2005
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 88 (12) , 3338-3345
Fabrication and Characterization of Ceramic Foams Based on Silicon Carbide Matrix and Hollow Alumino‐Silicate Spheres
Closed‐cell foams were fabricated by incorporating two different grades of hollow alumino‐silicate spheres (cenospheres) into a silicon carbide matrix. The matrix was formed by the pyrolysis of a preceramic polymer, and multiple polymer infiltration and pyrolysis (PIP) cycles were employed to minimize the open voids in the material. The physical, mechanical and thermal properties of the fabricated foams were characterized as functions of the number of reinfiltration cycles. The open‐ and closed‐void volume fractions were determined by measurements of bulk and skeletal densities. Mechanical properties, including strength and modulus, were evaluated using four‐point bend and compression tests. Finally, thermal properties of the material, including the coefficient of thermal expansion and the thermal conductivity, were determined using dilatometry and the laser‐flash technique, respectively. This processing technique results in closed‐cell syntactic foams with minimal porosity (∼2–4%), reasonable mechanical strength (∼30 MPa) and very low thermal conductivity (≤1 W/m·K). In this manner, this process can be used for the low‐cost and net‐shape fabrication of closed‐cell silicon carbide‐based syntactic foams for high‐temperature applications.
- 1 December 2002
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 36 (24) , 2713-2733
Degradation of Carbon Fiber-Reinforced Epoxy Composites by Ultraviolet Radiation and Condensation
The degradation of an IM7/997 carbon fiber-reinforced epoxy exposed to ultraviolet radiation and/or condensation has been characterized. Based on observations of physical and chemical degradation it has been established that these environments operate in a synergistic manner that causes extensive erosion of the epoxy matrix, resulting in a reduction in mechanical properties. Matrix dominated properties are affected the most, with the transverse tensile strength decreasing by 29% after only 1000 h of cyclic exposure to UV radiation and condensation. While, the longitudinal fiber-dominated properties are not affected for the exposure durations investigated, it has been noted that extensive matrix erosion would ultimately limit effective load transfer to the reinforcing fibers and lead to the deterioration of mechanical properties even along the fiber dominated material direction.
- 1 December 2002
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 36 (24) , 2713-2733
Degradation of Carbon Fiber-Reinforced Epoxy Composites by Ultraviolet Radiation and Condensation
The degradation of an IM7/997 carbon fiber-reinforced epoxy exposed to ultraviolet radiation and/or condensation has been characterized. Based on observations of physical and chemical degradation it has been established that these environments operate in a synergistic manner that causes extensive erosion of the epoxy matrix, resulting in a reduction in mechanical properties. Matrix dominated properties are affected the most, with the transverse tensile strength decreasing by 29% after only 1000 h of cyclic exposure to UV radiation and condensation. While, the longitudinal fiber-dominated properties are not affected for the exposure durations investigated, it has been noted that extensive matrix erosion would ultimately limit effective load transfer to the reinforcing fibers and lead to the deterioration of mechanical properties even along the fiber dominated material direction.