Stig Stenström
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Stig Stenström has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Anders Holmqvist
Lund Univ, Dept Chem Engn, SE-22100 Lund, Sweden
3 shared publications - Catherine Bonazzi
Université Paris-Saclay, INRAE, AgroParisTech, UMR SayFood, 91300 Massy, France
2 shared publications - Fredrik Magnusson
Department of Automatic Control, Lund University, SE-221 00 Lund, Sweden
2 shared publications - Loïc Foucat
QuaPA (Research Unit for Quality of Animal Products) INRA, 63122 Saint Genes Champanelle, France
2 shared publications - Tobias Törndahl
Department of Materials Science and Engineering Solar Cell Technology Uppsala University Uppsala Sweden
2 shared publications André Holmberg
Department of Chemical Engineering, Lund University, Lund, Sweden
1 shared publication
Latest Publications
- Open Access
- 4 April 2019
- Published by Taylor & Francis in Drying Technology
- Vol. 38 (7) , 825-845
Drying of paper: A review 2000–2018
Drying of paper during 2000–2018 is reviewed. The review includes new drying processes, multi-cylinder dryers, tissue and impingement drying, TAD-drying, infrared drying and energy use for drying of paper. It includes general aspects of infrared dryers but not drying of coated papers. Paper quality aspects, paper shrinkage and paper isotherms are not included. Impingement drying has been the most successful new technology with several applications while others such as impulse drying has not been commercialized mainly due to problems with paper quality parameters. One promising development is the introduction of steel instead of cast iron cylinders with increased heat transfer reducing the number of cylinders. Future research should focus on modeling the internal transport phenomena and to couple these phenomena to paper shrinkage and quality parameters. The influence of the fabric for the drying process needs more attention, understanding the drying process for new components such as microfibrillar cellulose in the stock and reducing energy use and increasing the amount of renewable energies for drying of paper.
- 4 April 2019
- Published by Taylor & Francis in Drying Technology
- Vol. 38 (7) , 825-845
Open AccessDrying of paper: A review 2000–2018
Drying of paper during 2000–2018 is reviewed. The review includes new drying processes, multi-cylinder dryers, tissue and impingement drying, TAD-drying, infrared drying and energy use for drying of paper. It includes general aspects of infrared dryers but not drying of coated papers. Paper quality aspects, paper shrinkage and paper isotherms are not included. Impingement drying has been the most successful new technology with several applications while others such as impulse drying has not been commercialized mainly due to problems with paper quality parameters. One promising development is the introduction of steel instead of cast iron cylinders with increased heat transfer reducing the number of cylinders. Future research should focus on modeling the internal transport phenomena and to couple these phenomena to paper shrinkage and quality parameters. The influence of the fabric for the drying process needs more attention, understanding the drying process for new components such as microfibrillar cellulose in the stock and reducing energy use and increasing the amount of renewable energies for drying of paper.
- Open Access
- 22 July 2017
- Published by Springer Nature in Cellulose
- Vol. 24 (10) , 4139-4149
Measurement of the flexibility of wet cellulose fibres using atomic force microscopy
- 22 July 2017
- Published by Springer Nature in Cellulose
- Vol. 24 (10) , 4139-4149
Open AccessMeasurement of the flexibility of wet cellulose fibres using atomic force microscopy
- 11 November 2016
- Published by Taylor & Francis in Drying Technology
- Vol. 35 (10) , 1167-1181
Drying of biofuels from the forest—A review
The literature during 2000–2016 about drying of biofuels from the forest has been reviewed. Biofuels constitute a low-cost energy resource that is likely to continue to increase and the dryers for such products should be simple, robust, and easy to operate. In 1970s and 1980s, rotary dryers and flash dryers were the most common types, and in 1990s, superheated steam (SHS) dryers became common. Maintenance costs and use of medium pressure steam for the SHS dryers are important topics to consider and one drawback for the rotary dryers is that high-temperature heat sources are used. The development during the last 15 years has moved toward moving bed dryers because of the possibility to use cheap low-temperature energy sources, robust design, and direct capacity control that is achieved by controlling the air temperature in the dryer. A price for the dry biofuel of 15–20 Euro/MWh has been indicated to make a dryer installation profitable based on no cost for the thermal energy and 40 Euro/MWh as the cost for the electrical energy. Shrinkage and the internal transport of moisture and heat in large particles of biofuels will need more considerations in the future. Fractionation of the biofuels, codrying with other products, the total cost for the drying process, environmental issues, and development of drying processes operating at high dew points are the other things to consider.
- 11 November 2016
- Published by Taylor & Francis in Drying Technology
- Vol. 35 (10) , 1167-1181
Drying of biofuels from the forest—A review
The literature during 2000–2016 about drying of biofuels from the forest has been reviewed. Biofuels constitute a low-cost energy resource that is likely to continue to increase and the dryers for such products should be simple, robust, and easy to operate. In 1970s and 1980s, rotary dryers and flash dryers were the most common types, and in 1990s, superheated steam (SHS) dryers became common. Maintenance costs and use of medium pressure steam for the SHS dryers are important topics to consider and one drawback for the rotary dryers is that high-temperature heat sources are used. The development during the last 15 years has moved toward moving bed dryers because of the possibility to use cheap low-temperature energy sources, robust design, and direct capacity control that is achieved by controlling the air temperature in the dryer. A price for the dry biofuel of 15–20 Euro/MWh has been indicated to make a dryer installation profitable based on no cost for the thermal energy and 40 Euro/MWh as the cost for the electrical energy. Shrinkage and the internal transport of moisture and heat in large particles of biofuels will need more considerations in the future. Fractionation of the biofuels, codrying with other products, the total cost for the drying process, environmental issues, and development of drying processes operating at high dew points are the other things to consider.
- 22 March 2016
- Published by Taylor & Francis in Drying Technology
- Vol. 35 (1) , 97-107
Modeling fixed-bed drying of bark
A model for fixed-bed drying of bark has been developed. The model takes heat and mass transfer between the air and bark into account and the volumetric heat transfer coefficient was used as fitting parameter in the model. The assumption of adiabatic saturation of the air leads to too high drying rates but a model with three size fractions shows good agreement both between experimental laboratory data and data from an industrial dryer. A sensitivity analysis for different air temperatures, air velocities, and bed heights show how the dryer capacity depends on these parameters.
- 22 March 2016
- Published by Taylor & Francis in Drying Technology
- Vol. 35 (1) , 97-107
Modeling fixed-bed drying of bark
A model for fixed-bed drying of bark has been developed. The model takes heat and mass transfer between the air and bark into account and the volumetric heat transfer coefficient was used as fitting parameter in the model. The assumption of adiabatic saturation of the air leads to too high drying rates but a model with three size fractions shows good agreement both between experimental laboratory data and data from an industrial dryer. A sensitivity analysis for different air temperatures, air velocities, and bed heights show how the dryer capacity depends on these parameters.
- 1 September 2014
- Published by Elsevier in Chemical Engineering Science
- Vol. 117, 301-317
Scale-up analysis of continuous cross-flow atomic layer deposition reactor designs
- 1 September 2014
- Published by Elsevier in Chemical Engineering Science
- Vol. 117, 301-317
Scale-up analysis of continuous cross-flow atomic layer deposition reactor designs
- 1 May 2014
- Published by Elsevier in Chemical Engineering Science
- Vol. 111, 15-33
Dynamic parameter estimation of atomic layer deposition kinetics applied to in situ quartz crystal microbalance diagnostics
- 1 May 2014
- Published by Elsevier in Chemical Engineering Science
- Vol. 111, 15-33
Dynamic parameter estimation of atomic layer deposition kinetics applied to in situ quartz crystal microbalance diagnostics
- 12 February 2014
- Published by Wiley
- p. 91-142
Magnetic Resonance Imaging for Determination of Moisture Profiles and Drying Curves
- 12 February 2014
- Published by Wiley
- p. 91-142
Magnetic Resonance Imaging for Determination of Moisture Profiles and Drying Curves
- 17 December 2008
- Published by Wiley
- p. 91-142
Magnetic Resonance Imaging for Determination of Moisture Profiles and Drying Curves
- 17 December 2008
- Published by Wiley
- p. 91-142
Magnetic Resonance Imaging for Determination of Moisture Profiles and Drying Curves
- 12 May 2008
- Published by Taylor & Francis in Drying Technology
- Vol. 26 (6) , 776-785
Modeling Drying and Energy Performance of Industrial Through-Dryers
A model of an industrial through-dryer for production of tissue paper was developed. The model can be used to predict the performance of a dryer section of an industrial through-drying machine consisting of one or more through-drying rolls separated by free draw sections. Roll diameters, wrap angles, machine speed, basis weight, initial paper moisture ratio, operating pressure differentials, drying air temperatures, and drying air humidity are input parameters to the model. Based on the input information, the model predicts paper drying rate, paper moisture ratio, paper temperature, exhaust air humidity, exhaust air temperature, and air flow rate as a function of time, which at a given machine speed is equivalent to a certain position in the machine direction of the dryer. The model also includes a description of the fabric and along with the paper properties the model also predicts fabric drying rate, fabric moisture ratio, fabric temperature, and fabric air humidity as a function of time (or position). Air, vapor, and enthalpy fluxes were integrated over the residence time of each through-drying roll in order to retrieve the average flow rate and air properties of the air leaving each roll. These data were then used in a steady-state description of the air system of each roll, which means that, for given drying conditions, natural gas consumption in the burners and the fan power associated with each roll can be predicted. The model was used to study how the different operating conditions affect the energy demand and economics of the through-drying process. The simulation results indicate small differences in total drying cost for different operating conditions. Reduction of fabric water was shown to have a relatively large impact on overall drying cost. Reducing the initial fabric moisture ratio from 0.019 to 0.012 kg water/kg dry solids reduced total operating costs by approximately 3.3%.
- 12 May 2008
- Published by Taylor & Francis in Drying Technology
- Vol. 26 (6) , 776-785
Modeling Drying and Energy Performance of Industrial Through-Dryers
A model of an industrial through-dryer for production of tissue paper was developed. The model can be used to predict the performance of a dryer section of an industrial through-drying machine consisting of one or more through-drying rolls separated by free draw sections. Roll diameters, wrap angles, machine speed, basis weight, initial paper moisture ratio, operating pressure differentials, drying air temperatures, and drying air humidity are input parameters to the model. Based on the input information, the model predicts paper drying rate, paper moisture ratio, paper temperature, exhaust air humidity, exhaust air temperature, and air flow rate as a function of time, which at a given machine speed is equivalent to a certain position in the machine direction of the dryer. The model also includes a description of the fabric and along with the paper properties the model also predicts fabric drying rate, fabric moisture ratio, fabric temperature, and fabric air humidity as a function of time (or position). Air, vapor, and enthalpy fluxes were integrated over the residence time of each through-drying roll in order to retrieve the average flow rate and air properties of the air leaving each roll. These data were then used in a steady-state description of the air system of each roll, which means that, for given drying conditions, natural gas consumption in the burners and the fan power associated with each roll can be predicted. The model was used to study how the different operating conditions affect the energy demand and economics of the through-drying process. The simulation results indicate small differences in total drying cost for different operating conditions. Reduction of fabric water was shown to have a relatively large impact on overall drying cost. Reducing the initial fabric moisture ratio from 0.019 to 0.012 kg water/kg dry solids reduced total operating costs by approximately 3.3%.