Masaharu Fukue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Masaharu Fukue has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Catherine N. Mulligan
Department of Building, Civil and Environmental Engineering, Concordia University, Montreal, Canada
4 shared publications - Zbigniew Lechowicz
Department of Geotechnical Engineering, Institute of Civil Engineering, Warsaw University of Life Sciences, Nowoursynowska 159, 02-776 Warsaw, Poland
4 shared publications - Yuichi Fujimori
Chubu Sokuchi Research Institute Co., 801-1 Konami, Suwa City 392-0131, Japan
3 shared publications - Kentaro Emori
Sanko Kaihatsu Co., Ltd., 1320 Gokanjima, Fuji City 416-0946, Japan
2 shared publications Y. Sato
Tokai University, Japan
2 shared publicationsYoshio Sato
Tokai University , Shizuoka , Japan
2 shared publications
Latest Publications
- Open Access
Properties and Behavior of Sandy Soils by a New Interpretation of MICP
Research on MICP technology for ground improvement began in the early 2000s, and since then, it has been considered as innovative research. The field of applications is showing signs of expanding from sandy soil stabilization to remediation. However, the research has not always progressed, because it is extremely difficult to evaluate the ability (viability rate) related to microorganisms and how to handle them quantitatively. In fact, this problem hinders the consensus of research results in terms of quantitative evaluation of microorganisms and the cross-comparison (evaluation) and use of MICP technology research. The crucial disadvantage of using bacteria is that their properties are not constant due to changes over time and in the surrounding environment. Therefore, for engineering purposes, we used the carbonate formation rate (CPR), instead of urease activity, as a function of the microbial mass (OD) with viable bacteria. Thus, the standard OD−CPR relationship was defined experimentally, and the estimation method of viability was established. The required amount of microorganisms for testing was given by OD*, and the relationship “OD = Rcv OD*” was defined to convert from OD* to OD. Rcv was defined as the viable bacterial rate. It was found that the Ca2+/OD ratio controls the inhibition behavior in MICP. At a Ca2+/OD ratio of >8.46 M, then inhibition occurs, while at Ca2+/OD = 8.46 M, CPR = 8.46 OD and the CPR is proportional to the viable OD, Rcv, and OD*. We show that it is possible to perform an experiment using OD* with aged bacteria, obtain Rcv from the standard OD−CPR and OD*−CPR relationships, convert OD* to OD and to perform a unified evaluation without actually determining the viability rate.
Open AccessProperties and Behavior of Sandy Soils by a New Interpretation of MICP
Research on MICP technology for ground improvement began in the early 2000s, and since then, it has been considered as innovative research. The field of applications is showing signs of expanding from sandy soil stabilization to remediation. However, the research has not always progressed, because it is extremely difficult to evaluate the ability (viability rate) related to microorganisms and how to handle them quantitatively. In fact, this problem hinders the consensus of research results in terms of quantitative evaluation of microorganisms and the cross-comparison (evaluation) and use of MICP technology research. The crucial disadvantage of using bacteria is that their properties are not constant due to changes over time and in the surrounding environment. Therefore, for engineering purposes, we used the carbonate formation rate (CPR), instead of urease activity, as a function of the microbial mass (OD) with viable bacteria. Thus, the standard OD−CPR relationship was defined experimentally, and the estimation method of viability was established. The required amount of microorganisms for testing was given by OD*, and the relationship “OD = Rcv OD*” was defined to convert from OD* to OD. Rcv was defined as the viable bacterial rate. It was found that the Ca2+/OD ratio controls the inhibition behavior in MICP. At a Ca2+/OD ratio of >8.46 M, then inhibition occurs, while at Ca2+/OD = 8.46 M, CPR = 8.46 OD and the CPR is proportional to the viable OD, Rcv, and OD*. We show that it is possible to perform an experiment using OD* with aged bacteria, obtain Rcv from the standard OD−CPR and OD*−CPR relationships, convert OD* to OD and to perform a unified evaluation without actually determining the viability rate.
- Open Access
Inhibited and Retarded Behavior by Ca2+ and Ca2+/OD Loading Rate on Ureolytic Bacteria in MICP Process
The estimation of optical density (OD) with viable cells is challenging for engineering purposes. In this study, the OD conversion based on previous study was used. The inhibited and retarded behavior of the microbially induced carbonate precipitation (MICP) process was examined. The experimental results showed that high Ca2+ drastically influences the inhibited and retarded behavior on MICP processes. The analysis showed that the inhibition and retardation effects occurred when the Ca2+/OD loading rate exceeded 8.46 M. The critical value was equal to the proportional constant for obtaining carbonate precipitation rate (CPR) from OD. Due to this, the blending design of materials became possible, with no risk of inhibition. In conclusion, the inhibition and retardation of the MICP process are governed by the Ca2+ load and the linear standard line (LSL), which may be attributed to the capacity or tolerance of viable cells, i.e., CPR/OD = 8.46 M or Ca2+/OD = 8.46 M.
Open AccessInhibited and Retarded Behavior by Ca2+ and Ca2+/OD Loading Rate on Ureolytic Bacteria in MICP Process
The estimation of optical density (OD) with viable cells is challenging for engineering purposes. In this study, the OD conversion based on previous study was used. The inhibited and retarded behavior of the microbially induced carbonate precipitation (MICP) process was examined. The experimental results showed that high Ca2+ drastically influences the inhibited and retarded behavior on MICP processes. The analysis showed that the inhibition and retardation effects occurred when the Ca2+/OD loading rate exceeded 8.46 M. The critical value was equal to the proportional constant for obtaining carbonate precipitation rate (CPR) from OD. Due to this, the blending design of materials became possible, with no risk of inhibition. In conclusion, the inhibition and retardation of the MICP process are governed by the Ca2+ load and the linear standard line (LSL), which may be attributed to the capacity or tolerance of viable cells, i.e., CPR/OD = 8.46 M or Ca2+/OD = 8.46 M.
- Open Access
Incorporation of Optical Density into the Blending Design for a Biocement Solution
The engineering practices for applying the microbial precipitation of carbonates require a design of the blending biocement solution (BCS). The BCS is usually blended with concentrated strains NO-A10, reaction media, such as urea and CaCl2, and a solvent, i.e., water or seawater. To characterize the BCS, the unknown microbial characteristics, such as the cell viability, are complex factors. Therefore, the optical density (OD) was redefined as Rcv OD*, in which OD* was the tentative OD of the BCS used and Rcv was the conversion rate concerning the cell viability. To determine Rcv values, a standard precipitation curve based on the precipitation rate at 24 h was determined. It was found that the curve was expressed by λ1 OD+ λ2 OD2, in which λ1 and λ2 were 8.46 M and −17.633 M, respectively. With this, the Rcv and OD values of unknown BCS were estimated from the results of precipitation tests using arbitrary OD* values. By extending the testing time, the second order term of OD or OD* was negligible. Accordingly, the precipitation amount is expressed as 8.46 OD, in which the OD can be estimated by precipitation tests using arbitrary OD* values of BCSs. Unless the Ca2+ value is dominant, the optimum blending of BCS can be determined by OD. Thus, it is concluded that the blending design of BCS is achieved using 8.46 OD, or 8.46 Rcv OD*, and the standard precipitation curve was defined in this study.
Open AccessIncorporation of Optical Density into the Blending Design for a Biocement Solution
The engineering practices for applying the microbial precipitation of carbonates require a design of the blending biocement solution (BCS). The BCS is usually blended with concentrated strains NO-A10, reaction media, such as urea and CaCl2, and a solvent, i.e., water or seawater. To characterize the BCS, the unknown microbial characteristics, such as the cell viability, are complex factors. Therefore, the optical density (OD) was redefined as Rcv OD*, in which OD* was the tentative OD of the BCS used and Rcv was the conversion rate concerning the cell viability. To determine Rcv values, a standard precipitation curve based on the precipitation rate at 24 h was determined. It was found that the curve was expressed by λ1 OD+ λ2 OD2, in which λ1 and λ2 were 8.46 M and −17.633 M, respectively. With this, the Rcv and OD values of unknown BCS were estimated from the results of precipitation tests using arbitrary OD* values. By extending the testing time, the second order term of OD or OD* was negligible. Accordingly, the precipitation amount is expressed as 8.46 OD, in which the OD can be estimated by precipitation tests using arbitrary OD* values of BCSs. Unless the Ca2+ value is dominant, the optimum blending of BCS can be determined by OD. Thus, it is concluded that the blending design of BCS is achieved using 8.46 OD, or 8.46 Rcv OD*, and the standard precipitation curve was defined in this study.
- Open Access
- 17 August 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (8) , 1395
Evaluation of the Undrained Shear Strength of Organic Soils from a Dilatometer Test Using Artificial Neural Networks
The undrained shear strength of organic soils can be evaluated based on measurements obtained from the dilatometer test using single- and multi-factor empirical correlations presented in the literature. However, the empirical methods may sometimes show relatively high values of maximum relative error. Therefore, a method for evaluating the undrained shear strength of organic soils using artificial neural networks based on data obtained from a dilatometer test and organic soil properties is presented in this study. The presented neural network, with an architecture of 5-4-1, predicts the normalized undrained shear strength based on five independent variables: the normalized net value of a corrected first pressure reading (po − uo)/σ′v, the normalized net value of a corrected second pressure reading (p1 − uo)/σ′v, the organic content Iom, the void ratio e, and the stress history indictor (oc or nc). The neural model presented in this study provided a more reliable prediction of the undrained shear strength in comparison to the empirical methods, with a maximum relative error of ±10%.
- 17 August 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (8) , 1395
Open AccessEvaluation of the Undrained Shear Strength of Organic Soils from a Dilatometer Test Using Artificial Neural Networks
The undrained shear strength of organic soils can be evaluated based on measurements obtained from the dilatometer test using single- and multi-factor empirical correlations presented in the literature. However, the empirical methods may sometimes show relatively high values of maximum relative error. Therefore, a method for evaluating the undrained shear strength of organic soils using artificial neural networks based on data obtained from a dilatometer test and organic soil properties is presented in this study. The presented neural network, with an architecture of 5-4-1, predicts the normalized undrained shear strength based on five independent variables: the normalized net value of a corrected first pressure reading (po − uo)/σ′v, the normalized net value of a corrected second pressure reading (p1 − uo)/σ′v, the organic content Iom, the void ratio e, and the stress history indictor (oc or nc). The neural model presented in this study provided a more reliable prediction of the undrained shear strength in comparison to the empirical methods, with a maximum relative error of ±10%.
- 16 May 2012
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 30 (3) , 222-233
Re-Suspension Technique for Improving Organic Rich Sediment-Water Quality in a Shallow Sea Area
The re-suspension method consists of (1) dispersion of the sediment by air-water jets, (2) pumping of the suspension (small particles and organic matter), (3) settlement in a tank, (4) filtration and (5) disposal of solids (followed by incineration in this case). The pilot test was performed to clean up an area of 3000 m2. The dispersed depth of the bottom was approximately 50 cm. The time spent for the work was two weeks. The amount of re-suspended solid removed from the bottom was about 8 tonnes in dry mass. Since the solids contain high concentrations of chemical oxygen demand (COD), total phosphorous (T-P), total nitrogen (T-N) and sulfides, the remaining sediment was considerably improved. Quantitative analyses showed that the full-scale implementation would enable the removal of about 10% of the re-suspended solids, and reduce COD by 95%, T-P by 50%, T-N by 100% and sulfide by 75% for re-deposited sediments in comparison to the original sediments.
- 16 May 2012
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 30 (3) , 222-233
Re-Suspension Technique for Improving Organic Rich Sediment-Water Quality in a Shallow Sea Area
The re-suspension method consists of (1) dispersion of the sediment by air-water jets, (2) pumping of the suspension (small particles and organic matter), (3) settlement in a tank, (4) filtration and (5) disposal of solids (followed by incineration in this case). The pilot test was performed to clean up an area of 3000 m2. The dispersed depth of the bottom was approximately 50 cm. The time spent for the work was two weeks. The amount of re-suspended solid removed from the bottom was about 8 tonnes in dry mass. Since the solids contain high concentrations of chemical oxygen demand (COD), total phosphorous (T-P), total nitrogen (T-N) and sulfides, the remaining sediment was considerably improved. Quantitative analyses showed that the full-scale implementation would enable the removal of about 10% of the re-suspended solids, and reduce COD by 95%, T-P by 50%, T-N by 100% and sulfide by 75% for re-deposited sediments in comparison to the original sediments.
- 29 March 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 4050-4059
Improvement of Sediment-Water Quality by Resuspension
Heavy eutrophication was found in a canal located in the central part of Fukuyama City, Japan due to a high organic content (30 percent loss on ignition). As a result, hydrogen sulfide production often occurred, mostly from spring to autumn. Therefore, Fukuyama City decided to investigate the possibility of cleaning up the bottom of the canal using a resuspension technique. The pilot test was evaluated for an area of 3000 m2. The amount of wet resuspended solids removed from the bottom of the water column was about 11 tonnes. The ORP of the surface sediments was initially -150 mV but increased to above +70 mV after redeposition. In comparison to the original sediments, quantitative analyses showed that full scale implementation would enable the removal of about 10 % of the resuspended solids, and reduce COD by 95 %, T-P by 50 %, T-N by 100 % and sulfide by 75 % for redeposited sediments.
- 29 March 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 4050-4059
Improvement of Sediment-Water Quality by Resuspension
Heavy eutrophication was found in a canal located in the central part of Fukuyama City, Japan due to a high organic content (30 percent loss on ignition). As a result, hydrogen sulfide production often occurred, mostly from spring to autumn. Therefore, Fukuyama City decided to investigate the possibility of cleaning up the bottom of the canal using a resuspension technique. The pilot test was evaluated for an area of 3000 m2. The amount of wet resuspended solids removed from the bottom of the water column was about 11 tonnes. The ORP of the surface sediments was initially -150 mV but increased to above +70 mV after redeposition. In comparison to the original sediments, quantitative analyses showed that full scale implementation would enable the removal of about 10 % of the resuspended solids, and reduce COD by 95 %, T-P by 50 %, T-N by 100 % and sulfide by 75 % for redeposited sediments.
- 31 January 2010
- Published by Elsevier in Applied Clay Science
- Vol. 47 (1-2) , 133-138
Evidence of the production and dissolution of carbonate phases in bentonite formations
- 31 January 2010
- Published by Elsevier in Applied Clay Science
- Vol. 47 (1-2) , 133-138
Evidence of the production and dissolution of carbonate phases in bentonite formations
- 1 August 2006
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 136 (1) , 111-119
Background values for evaluation of heavy metal contamination in sediments
- 1 August 2006
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 136 (1) , 111-119
Background values for evaluation of heavy metal contamination in sediments
- 18 July 2003
- Published by Elsevier in Applied Clay Science
- Vol. 23 (1-4) , 169-177
Change in microstructure of soils due to natural mineralization
- 18 July 2003
- Published by Elsevier in Applied Clay Science
- Vol. 23 (1-4) , 169-177
Change in microstructure of soils due to natural mineralization